期刊文献+

超音速火焰喷涂WC-12Co涂层的磨粒磨损行为研究

Study on Abrasive Wear Behavior of HVOF Deposited WC-12Co Coating
下载PDF
导出
摘要 对超音速火焰WC-12Co涂层进行了密粒磨损试验,研究了磨粒磨损试验参数对涂层性能的影响,并通过SEM对涂层表面的显微形貌进行了观察分析,探讨了WC-12Co涂层的磨粒磨损失效机制。结果表明:涂层的失重随试验载荷及磨料直径的增加而增加:在载荷或磨料粒度较大时,涂层的磨损失效形式为晶粒剥落及犁沟切削相结合;当栽荷或磨料粒度较小时,其失效形式主要为晶粒剥落方式。 The abrasive wear performance has been investigated of high velocity oxy-fuel(HVOF)sprayed WC-12Co coating.The influences with different load size and abrasive properties of the wear performance have been investigated.The microscopic morphology has been observed by SEM method,and the failure mechanisms of WC-12Co abrasive coating have been discussed.The results show that the coating weight loss with the load and abrasive diameter increases;In the larger load or abrasive size,the coating wear failure for plo...
出处 《太原科技》 2008年第2期75-76,79,共3页 Taiyuan Science and Technology
关键词 超音速火焰喷涂 WC-12CO 磨粒磨损 high velocity oxy-fuel spraying WC-12Co abrasive wear
  • 相关文献

参考文献2

二级参考文献9

  • 1徐滨士,第八届全国焊接年会论文集,1997年,148页
  • 2Dong F,Wear,1995年,180卷,35页
  • 3Ohmari A,Thin Solid Films,1991年,201卷,241页
  • 4Arata Y,Trans JWRI,1986年,15卷,2期,339页
  • 5Vuoristo P,Niemi k,Makela A et al.Abrasion and Erosion Wear Resistance of Cr3 C2-NiCr Coatings Prepared by Detonation and High Velocity Oxy-Fuel Spraying[].Proceedings of the th National Thermal Spray Conference Boston Massachusetts:.1994
  • 6Fukuda Y,Kumon M.Application of High Velocity Flame Spraying for the Heat Exchanger Tubes in Coal Fired Boilers[].Proc of the th ITSCKobe:.1995
  • 7Zhou K S,Yang D J,Zeng A Q et al.WC-Cr-Co Coating for Mandrel of Precision Forging Machine[].Proc of the th ITSC Orlando Florida:.1992
  • 8Lugscheider E,Remer P,Herbst C et al.NiCr-Cr3 C2 and NiCr-TiC-High Wear Resistant Coatings for Protective Applications in Steam Turbines[].Proc of the th ITSC Kobe:.1995
  • 9Knight R,Smith R W.HVOF Sprayed 80/20NiCr Coatings-Process Influence Trends[].Proc of the th ITSC Orlando Florida :.1992

共引文献22

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部