期刊文献+

KDP晶体飞刀铣削加工参数对表面质量影响的实验研究 被引量:3

Experimental Investigation of Processing Technology for Surface Quality of KDP Crystal Machined by Single Point Diamond Turning
原文传递
导出
摘要 本文通过实验研究了刀具前角、背吃刀量及进给量对KDP晶体表面粗糙度及表面波纹度的影响规律。研究结果表明,采用单点金刚石飞刀铣削方法加工KDP晶体光学元件的最佳刀具前角为-45°;背吃刀量对已加工表面的粗糙度影响不大;表面粗糙度随进给量增加而增大;已加工表面的波纹度与机床的工作状态有关,需采用合理的加工参数组合来保证。 The relationships of roughness and waveness with rake, cutting depth and feed are well investigated to KDP(potassinm dihydengen phosphate) crystals.The research result indicates that using single point diamond turning method the best rake of cutter to machine KDP crystal optical element is-45°;the cutting depth has just a little effect to the roughness of the finished surface;the roughness increases as the feed growing;the waveness of the finished surface is related with the working condition of the machine, and a better waveness needs to be obtained by an appropriate combination of the processing parameters.
出处 《航空精密制造技术》 2009年第5期4-7,共4页 Aviation Precision Manufacturing Technology
关键词 KDP晶体 惯性约束核聚变 单点金刚石飞刀铣削 potassinm dihydengen phosphate crystal inertial confinement fusion single point diamond turning
  • 相关文献

参考文献6

二级参考文献48

  • 1Chol K S, John S T. Diamond turning:Optimum machining of opticals[J]. Mechanical Engineering, 1991, (4):68--72.
  • 2Kozlowski M R, Thomas I, Edwards G, et al. Influence of diamond turning and surface cleaning processes on the degradation of KDP crystal surfaces[J]. Proceedings of SPIE, 1561 :59--69.
  • 3Rigatti A L, Smith D J. Moisture barrier coatiogs to prevent environmental degradation of KDP crystal [ J ]. Proceedings of SPIE,2000,4347:139.
  • 4Viktor I. BESPALOV,Vladimir I. BREDIKHIN,V. P. ERSHOV,et al. Effective technology of fabricating KDP, DKDP crystals to be used in high-energy lasers[J]. SPIE,1997,2633:732-739.
  • 5FISCHER-CRIPPS A C,LAWN B R. Symmetry. Indentation stress-strain curves for "quasi-ductile" ceramics[J]. Acta Metallurgica et Materialia,1996,44(2):519-527.
  • 6BLAKE P N,SCATTERGOOD R O. Ductile-regime machining of germanium and silicon[J]. J.Am.Ceram.Soc,1990,73(4):949-957.
  • 7Baruch A. FUCHS,P. Paul HED,Phillip C. BAKER. Fine diamond turning of KDP crystals[J]. Applied Optics,1986,25(11):1733-1735.
  • 8Liang Y, Moronuki N, Furukawa Y. Calculations of the effect of material anisotropy on microcutting processes. Precision Engineering, April 1994, Vol. 16(2): 132- 138.
  • 9Furukawa Y, Nobuyuki M. Effect of material properties on ultra-precision cutting processes. Annals of the CIRP, 1988, 37:113.
  • 10Moronuki N, Liang Y, Fumkawa Y. Experiments on the effect of material properties on micro-cutting processes. Precision Engineering, 1994, 16:124.

共引文献56

同被引文献24

引证文献3

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部