期刊文献+

共注成型芯壳层熔体粘度对芯壳层界面和移动前沿形貌的影响 被引量:18

EFFECT OF CORE-SKIN VISCOSITY RATIO ON THE FORMATION OF LAYER INTERFACE AND MOVING MELT FRONTS DURING MOLDING FILLING OF CO-INJECTION
下载PDF
导出
摘要  建立了共注成型充模流动的有限元模型,并利用Matlab与VisualC++6.0混合编程技术开发了模拟软件,利用该软件对芯壳层熔体的粘度与芯壳层界面和移动前沿形貌之间的关系进行了数值模拟,并提出了确定关键成型工艺参数的指导原则。模拟研究结果与一些文献的实验结果相吻合。 A finite-element model is established for the mold filling of co-injection, and a software package of numerical simulation was developed by means of Matlab and Visual C++ 6.0. The numerical simulation of the relation was implemented between the core-skin-viscosity ratio and the formations of layer interface and moving melt fronts, and then a set of principles to guide the selection of the key molding parameters was put forward. The result of case study of numerical simulation is in good agreement with the experimental result given in some literature.
出处 《复合材料学报》 EI CAS CSCD 北大核心 2004年第4期24-28,共5页 Acta Materiae Compositae Sinica
基金 国家自然科学基金(20274016) 国家留学归国人员科研启动基金 江西省自然科学基金 江西省教委科技计划 江西省主要学科跨世纪学术带头人培养计划资助项目
关键词 共注成型 充模 多相分层流动 数值模拟 Computer simulation Finite element method Mathematical models Viscosity
  • 相关文献

参考文献8

  • 1Johnson C, Pitkaranta J. An analysis of the discontinuous Galerkin method for a scalar hyperbolic equation [J ].Mathematics of Computation, 19 8 6, 4 6 ( 17 3) : 1 - 2 6.
  • 2Lanvers A, Galuschka S, Tietz W. Injection moulding made transparent-new developments in process simulation [A].In: 16th Colloquium of the German Institute of Rubber Processing (IKV)[C]. Aachen: The German Institute of Rubber Processing, 1992. 6-12.
  • 3Somnuk P, Smith G F. Experiment study of simultaneous coinjection moulding process [A]. In: Proceedings of Annual Technical Conference (Vol. 1): Processing [C]. Boston: The Society of Plastics Engineers, 1995. 760- 764.
  • 4Ilinca F, Derdouri A. Numerical simulation and experimental validation of the filling stage in the co-injection molding process [A]. In: Proceedings of Annual Technical Conference (Vol. 1): Processing [C]. Nashville: The Society of Plastics Engineers, 200
  • 5Li C J, Lee D J, Isayev A Ⅰ. Interface development and encapsulation in simultaneous coinjection molding of disk (Ⅱ): Two-dimensional simulation and experiment [J].Journal of Applied Polymer Science, 2003, 88 (9): 2310 -2318.
  • 6江顺亮.RTM加工工艺充模过程的计算机模拟[J].复合材料学报,2002,19(2):13-17. 被引量:34
  • 7江顺亮.树脂传递成型加工注射口位置的快速优化法[J].复合材料学报,2002,19(4):18-24. 被引量:5
  • 8王利霞,申长雨,陈静波,刘春太.注塑充模过程中温度场的数值分析[J].中国塑料,2001,15(6):55-59. 被引量:6

二级参考文献6

共引文献41

同被引文献105

引证文献18

二级引证文献42

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部