期刊文献+

THE MICROSTRUCTURAL BANDING IN THE CENTER OF HOT ROLLLNG STRIP 被引量:4

下载PDF
导出
摘要 The microstructural banding in steels is often found in hot rolling strips, which plays a very important role in mechanical properties. Much work has been done to investigate how the microstructural banding is formed during hot rolling. In the present study, the microstructure of hot rolling strips was examined in term of optical microscopy and transmission electron microscopy. Electron probe microanalysis was also used to decide the distribution of microchemical bands, by this means, the phases in these strips were found to be ferrite and pearlite. The average distance between the carbon lamellas in pearlite is about 0.06-0.1μm. It is also shown that microstructural banding in hot rolled carbon steel was closely related to the segregation of manganese and silicon into those bands. Based on the transformation kinetic, the simulated results pointed out that the thermodynamic stability of austenite would increase with the increasing of Mn, which led to a decrease of ferrite growth rate. The effect of Mn on the decomposition of austenite is attributed to segregation of Mn atoms along the ferrite/austenite phase boundary which causes a strong solute drag effect. The addition of Mn to steel decreases the activity of austenite, thereby it is beneficial to the formation of non-equilibrium phase, such as degenerate pearlite. The formation of banded structure on the hot rolled process was discussed. The microstructural banding in steels is often found in hot rolling strips, which plays a very important role in mechanical properties. Much work has been done to investigate how the microstructural banding is formed during hot rolling. In the present study, the microstructure of hot rolling strips was examined in term of optical microscopy and transmission electron microscopy. Electron probe microanalysis was also used to decide the distribution of microchemical bands, by this means, the phases in these strips were found to be ferrite and pearlite. The average distance between the carbon lamellas in pearlite is about 0.06-0.1μm. It is also shown that microstructural banding in hot rolled carbon steel was closely related to the segregation of manganese and silicon into those bands. Based on the transformation kinetic, the simulated results pointed out that the thermodynamic stability of austenite would increase with the increasing of Mn, which led to a decrease of ferrite growth rate. The effect of Mn on the decomposition of austenite is attributed to segregation of Mn atoms along the ferrite/austenite phase boundary which causes a strong solute drag effect. The addition of Mn to steel decreases the activity of austenite, thereby it is beneficial to the formation of non-equilibrium phase, such as degenerate pearlite. The formation of banded structure on the hot rolled process was discussed.
出处 《Acta Metallurgica Sinica(English Letters)》 SCIE EI CAS CSCD 2005年第5期664-668,共5页 金属学报(英文版)
基金 This work was supported by the National High Technical Reasearch and Development Programme of China(No.2001AA339030) Shenyang Ligong University Foundation(No.3200903).
关键词 PEARLITE FERRITE microstructural banding hot rolling strip pearlite, ferrite, microstructural banding, hot rolling strip
  • 相关文献

参考文献10

  • 1M. Thompon, M. Ferry and P.A. Manohar, ISIJ41 (2001) 891.
  • 2F.A. Khalid, M. Farooque and A. Ulhaq, MST 15 (1999) 1209.
  • 3T.A. Kop, J. Sietsma and S. Van der Zwaag, MST 17 (2001) 1569.
  • 4R. Grobterlinden, R. Kawalla, U. Lotter and H. Pircher, Steel Research 63 (1992) 331.
  • 5M. Thompon, M. Ferry and P.A. Manohar, ISIJ41 (2001) 891.
  • 6F.A. Khalid, M. Farooque and A. Ulhaq, MST 15 (1999) 1209.
  • 7T.A. Kop, J. Sietsma and S. Van der Zwaag, MST 17 (2001) 1569.
  • 8S.W. Thompson and P.R. Howell, MST 8 (1992) 777.
  • 9M. Hillert and L.I. Staffansson, Acta Chem. Scan. 24 (1970)3618.
  • 10B. Sundmanand J. Agren, J. Phys. Chem. Solid. 42 (1981) 297.

同被引文献33

引证文献4

二级引证文献65

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部