期刊文献+

带鳍状凸肩结构汽轮机叶片的接触分析 被引量:2

Contact Analysis of Steam Turbine Blades With Fin Heaves
下载PDF
导出
摘要 为了研究大型汽轮机叶片旋转过程中鳍状凸肩间的接触状态,利用拉格朗日增广算法,采用三维有限元模型,计算了考虑摩擦情况下的凸肩间接触压力的变化情况,得出了接触压力与转速之间的关系,并计算了3000r/min下整圈叶片的固有频率.计算表明:当叶片转速达到400r/min时,鳍状凸肩开始接触,此后随着转速的增加,鳍状凸肩间的接触压力逐渐增大,接触面积不断扩大;当转速为1825r/min时,接触压力增加程度明显趋缓;转速为3000r/min时接触压力最大(700MPa),鳍状凸肩间的实际接触面积为设计接触面积的1/4左右. For rotating blades with fin heaves used in steam turbines, large deflection and contact effects must be taken into account. By using 3-D finite element model and the augmented Lagrangian formulation, contact pressure between fin heaves is analyzed. Contact friction considered, the relation curve of the contact pressure vs. rotating speed is obtained and intrinsic frequencies of blades at 3 000 r/min are calculated. Calculating resuits show that two neighbored fin heaves become to contact at rotating speed of 400 r/min. After this, contact pressure increases steadily as the rotating speed increases. However, as the speed reaches 1 825 r/min, increasing of the contact pressure becomes to slow down apparently. At 3 000 r/min, the contact pressure reaches its maximum of 700 MPa and the contact area is about 1/4 of the design contact area.
出处 《北京工业大学学报》 CAS CSCD 北大核心 2005年第6期566-569,共4页 Journal of Beijing University of Technology
关键词 汽轮机叶片 鳍状凸肩 接触分析 有限元方法 steam blades fin heaves contact analysis finite element method (FEM)
  • 相关文献

参考文献9

  • 1李辛毅,季葆华,孟庆集.采用整体围带或翅翼形凸肩提供摩擦阻尼的叶片典型结构[J].汽轮机技术,1996,38(4):217-220. 被引量:5
  • 2SANO N A. A penalty function type of virtual work principle for impact contact problem of two bodies [J]. Bull JSME,1986, 29(257): 3701-3709.
  • 3HUGHES T J, TAYLOR R L, SACKMAN J L, et al. A finite element method for a class of contact-impact problems [J].Comput Meth Appl Mech Engng, 1976, 8(3): 249-276.
  • 4WRIGGERS P, VAN T, STEIN E. Finite dement formulation of large deformation impact-contact problems with friction[J].Computers & Structures, 1990, 37(3): 319-331.
  • 5PERIC D, OWEN D R J. Computational model for 3-D contact problems with friction based on the penalty method [J]. Int J Num Methods Engng, 1992, 35(6): 1289-1309.
  • 6BERTSEKAS D P. Constrained Optimization and Lagrange Multiplier Methods [M]. New York: Academic Press, 1969.
  • 7PAPDOPOULOS P, SOLBERG J M. A Lagrangian multiplier method for the finite element solution of frictionless contact problems [J]. Math Comput Modelling, 1998, 28(4-8): 373-384.
  • 8JIANG Lei, ROGERS R J. Combined Lagrangian multiplier and penalty function finite element technique for elastic impact analysis[J]. Computers & Structures, 1988, 30(6): 1219-1229.
  • 9SIMO J C, LAURSEN T A. An augmented Lagrangian treatment of contact problems involving friction[J]. Computers & Structures, 1992, 42(1): 97-116.

二级参考文献2

共引文献4

同被引文献40

引证文献2

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部