期刊文献+

电容层析成像系统三维电场分析及阵列电极优化 被引量:8

Three-Dimensional Electric Field Simulation and Electrode Array Optimization in Electrical Capacitance Tomography System
下载PDF
导出
摘要 通过电磁场有限元软件ANSYS仿真,构建电容层析成像(ECT)系统敏感阵列电极三维模型,分析ECT敏感场的"软场"效应,推导计算灵敏度矩阵,并分析敏感阵列电极结构参数对ECT电场灵敏度的影响,进而优化阵列电极结构.实验结果表明,利用优化的阵列电极可获得较均匀的敏感场分布及较高的检测灵敏度,并重构出较满意的图像. By using ANSYS for formulation and solution of the finite element, a three- dimensional model of electrical capacitance tomography (ECT) electrode array was constructed. Based on this model, the 'soft-field' effect in sensing field affected by distribution of the object was considered, sensitivity matrix was calculated and the effect of structural parameters of sensing electrode array on sensitivity response was analyzed. And thereby the optimum configuration of the electrode array was obtained. The test results indicate that with the optimized electrode array the homogeneous sensitive field distribution, high measurement sensitivity and reconstructed image can be obtained.
出处 《天津大学学报》 EI CAS CSCD 北大核心 2007年第9期1041-1047,共7页 Journal of Tianjin University(Science and Technology)
基金 国家自然科学基金资助项目(60532020 60301008 50337020 60472077) 国家高技术研究发展计划专项经费资助项目(2006BAI03A00) 河南省自然科学基金资助项目(0511012100.)
关键词 电容层析成像 阵列电极 '软场'效应 ANSYS 三维电场仿真 electrical capacitance tomography electrode array "soft-field" effect ANSYS three-dimensional electric field simulation
  • 相关文献

参考文献8

  • 1Jaworskvi A J,Bolton G T.The design of an electrical capacitance tomography sensor for use with media of high dielectric permittivity[ J ].Measurement Science and Technology,2000,11 (6):743-757.
  • 2王化祥,朱学明,张立峰.用于电容层析成像技术的共轭梯度算法[J].天津大学学报(自然科学与工程技术版),2005,38(1):1-4. 被引量:38
  • 3Yang W Q.Hardware design of electrical capacitance tomography systems[ J ].Measurement Science and Technology,1996 (7):225-232.
  • 4Xie C G,Huang S M,Hoyle B S,et al.Electrical capacitance tomography for flow imaging:System model for development of image reconstruction algorithms and design of primary sensors[J].IEE Proceedings,1992,139 (1):89-98.
  • 5Walman R,Mazurklewicz L,Banasiak R,et al.Numerical calculation of forward problem for 3D capacitance tomography[ C ]//4th World Congress on Industrial Process Tomography.Aizu,Japan,2005:588-593.
  • 6Xie C G,Stott A L,Plaskowski A.Design of capacitance electrodes for concentration measurement of two phase flow[ J ].Measurement Science and Technology,1991,1(1):65-78.
  • 7王化祥,张立峰,朱学明.电容层析成像系统阵列电极的优化设计[J].天津大学学报(自然科学与工程技术版),2003,36(3):307-310. 被引量:30
  • 8Yang W Q,Peng Lihui.Image reconstruction algorithms for electrical capacitance tomography[ J ].Measurement Science and Technology,2003,14 (1):R1-R13.

二级参考文献9

  • 1南京大学数学系.计算数学专业:最优化方法[M].北京:科学出版社,1978..
  • 2Xie C G, Stott A L, Plaskowski A et al. Design of capacitance electrodes for concentration measurement of two-phase flow [ J ]. Measurement Science and Technology, 1990, 1( 1 ) :65-78.
  • 3Xie C G, Huang S M, Hoyle B S et al. Electrical capacitance tomography for flow imaging: system model for development of image reconstruction algorithms and design of primary sensors[J]. IEEE Proc G, 1992, 139(1):89-98.
  • 4Xie C G. Mass flow measurement of solid in a gravity drop conveyor using capacitance transducer[ D]. U K : University of Manchester, 1988.
  • 5Xie Chenggang, Huang Songming, Hoyle B S, et al. Electrical capacitance tomography for flow imaging:System model for development of image reconstruction algorithms and design of primal" sensors [ J ]. IEEE Proc G, 1992, 139 ( 1 ) :89--98.
  • 6Yang Wuqiang, Peng Lihui. Image reconstruction algorithms for electrical capacitance tomography [J]. Measurement Science and Technology,2003, 14 : 1-13.
  • 7Liu Shi, Fu Li, Yang Wuqiang. Optimization of an iterative image reconstruction algorithm for electrical capacitance tomography[ J ]. Measure Science and Technology, 1999,10 :37--39.
  • 8王化祥,杨五强.电容过程成像技术的进展[J].仪器仪表学报,2000,21(1):4-7. 被引量:36
  • 9张宝芬,焦清,黄松明.电容式两相流相浓度传感器的仿真及优化[J].清华大学学报(自然科学版),1992,32(1):25-31. 被引量:13

共引文献60

同被引文献79

引证文献8

二级引证文献21

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部