期刊文献+

新型防护壁板钢极限拉深系数的预估和试验验证 被引量:1

Pre-evaluation and Test Validation for the Minimum Drawing Coefficient of the New Type Protection Wall Plate Iron
下载PDF
导出
摘要 为了解决某防护壁板拉深成形时的拉裂问题,提出了预估极限拉深系数的理论和试验方法。首先分析了拉深过程中危险断面的位置及变薄规律,然后根据筒壁传力区的最大拉力应当小于危险断面的抗拉强度计算得到极限拉深系数。为测定壁板材料的拉深性能,进行了工艺试验,初步预估了材料的极限拉深系数、拉深力、压边力等参数。利用试验方法对预估的数值进行了验证。结果表明,利用本方法可以较准确地得到材料的极限拉深系数,对于解决新型材料复杂形状拉深件的拉深缺陷问题具有参考作用。 In order to solve the fracture defect when drawing a certain type protection wall plate iron, a pre-evaluation and test validation method for the minimum drawing coefficient has been proposed.First ,the location of hazard section and the thinning rule has been analyzed when drawing.Then ,the minimum drawing coefficient has been deduced according to the fact that the maximum tensile strength at the force-transition area should be less than that at the hazard section.For testing the drawing performance of the plate material, the processing test has been executed, and the minimum drawing coefficient, drawing force and the pressure force have been calculated. These values have been validated by test method.The results show that this method can obtain the minimum drawing coefficient accurately, and it can be referred for solving the drawing problem of new type of material and complicated products.
作者 翁黎清
出处 《锻压装备与制造技术》 2008年第1期66-68,共3页 China Metalforming Equipment & Manufacturing Technology
基金 福建省自然科学基金资助项目(2007J0355) 福建省教育厅科技计划项目(JA04251)
关键词 机械制造 估算 拉深系数 拉深 防护壁板 Pre-evaiuation Drawing coefficient Protection wall plate iron
  • 相关文献

参考文献6

  • 1王孝培.冲压手册[M].北京:机械工业出版社,2004.
  • 2刘琼,黎文峰.汽车前翼子板拉深成形模拟中两种工艺方案比较[J].锻压装备与制造技术,2007,42(2):62-65. 被引量:3
  • 3Fuh-Kuo Chen,Yeu-Ching Liao.Analysis of draw-wall wrinkling in the stamping of a motorcycle oil tank [J].Journal of Materials Processing Technology.2007,192/193 ( 1-3 ) :200-203.
  • 4黄跃东,邱晓刚,陈文龙.板料成形模拟坯料网格尺寸的控制[J].锻压装备与制造技术,2007,42(4):63-65. 被引量:3
  • 5R.Padmanabhan,M.C.Oliveira,L.F.Menezes.Deep drawing of aluminium-steel tailor-welded blanks[J].Materials & Design ,2008,29 (1):154-160.
  • 6Z.Tourki,K.Sai.Design and loading parameter optimisation in deep drawing process [J].Intertional Journal of Vehicle Design.2005,39 ( 1/2):25-37.

二级参考文献13

共引文献41

同被引文献6

  • 1刘琼,黎文峰.汽车前翼子板拉深成形模拟中两种工艺方案比较[J].锻压装备与制造技术,2007,42(2):62-65. 被引量:3
  • 2Lihui Lang, Joachim Danckert, Karl Brian Nielsen.Investigation into hydrodynamic deep drawing assisted by radial pressure: Part Ⅱ.Numerical analysis of the drawing mechanism and the process parameters [J].Joumal of Materials Processing Technology, 2005,166 ( 1 ): 150-161.
  • 3J.Tirosh,A.Shirizly,D.Ben-David,et al.Hydro-rim deep-drawing processes of hardening and rate-sensitive materials[J].Intemational Journal of Mechanical Sciences, 2000,42( 6 ): 1049-1067.
  • 4Halil.Ibrahim Demirci,Cemal Esner, Mustafa Yasar. Effect of the blank holder force on drawing of aluminum alloy square cup: Theoretical and experimental investigation [J].Journal of Materials Processing Technology, 2008,206( 1-3 ): 152-160.
  • 5Swadesh Kumar Singh, D.Ravi Kumar. Effect of process parameters on product surface finish and thickness variation in hydro-mechanical deep drawing [J].Journal of Materials Processing Technology, 2008,204( 1-3):169-178.
  • 6M.Khelifa, M.Oudjene. Numerical damage prediction in deep-drawing of sheet metals [J].Journal of Materials Processing Technology, 2008,200( 1-3 ):71-76.

引证文献1

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部