期刊文献+

锐角模具通道等径角挤压有限元分析 被引量:5

Finite Element Analysis on Equal Channel Angular Pressing with Acute Die Channel Angle
下载PDF
导出
摘要 采用有限元模拟研究了1100Al锐角模具通道(准=60°)等径角挤压时的坯料流动、等效应变、挤压应力以及速度分布。与准=90°模具等径角挤压坯料相比,锐角模具通道等径角挤压可以在坯料内产生更大的等效应变,有助于提高挤压的效率;但挤压过程中在两通道相交外侧尖角处出现死区,由于死区的影响,坯料横截面上等效应变分布不均匀,挤出坯料下表面区域等效应变明显高于其他区域,同时,由于挤压应力明显上升,对挤压设备以及工模具提出更高的要求。因此,锐角模具通道等径角挤压比较适合于塑性较好、强度较低的材料。 The billet flow, effective strain, extrusion stress and velocity distribution of 1100Al was investigated using finite element simulation in acute die channel angle. Compared with φ=90° die channel angle, the higher effective strain was introduced into the billet through acute die channel angle. It was helpful for improving the production efficiency. But the dead zone was found in the outer sharp comer of two channels intersection, which caused non-uniform distribution of effective strain along the cross-section of the pressed billet. The magnitude of effective strain near the bottom of the pressed billet was obviously higher than other zones. At the same time, as a result of the extrusion stress increased obviously, the requirement for extrusion equipment and tools was raised. So equal channel angular pressing with acute die channel angle is relatively fit for the materials with better plasticity and lower strength.
出处 《热加工工艺》 CSCD 北大核心 2008年第15期61-64,共4页 Hot Working Technology
基金 国家自然科学基金资助项目(50575097)
关键词 锐角模具通道 等径角挤压 有限元分析 等效应变 挤压应力 acute die channel angle equal channel angular pressing finite element analysis effective strain extrusion stress
  • 相关文献

参考文献11

  • 1Segal V M,Reznikov V I,Drobyshevkiy A E, et rd. Plastic working of metals by simple shear [J]. Russian Metallurgy, 1981, (1):99-115.
  • 2Shin D H,ParkKT. Ultrafine grained steels processod by equal channel angular pressing [J]. Materials Science and Engineering,2005 ,A410-411 : 299-302.
  • 3石凤健,王雷刚,王海龙,汪建敏.等径角挤压工艺对固溶状态CuCrZr合金性能的影响[J].金属热处理,2007,32(1):81-83. 被引量:4
  • 4石凤健,汪建敏,许晓静.ECAP法制备超细晶铜的再结晶行为研究[J].热加工工艺,2005,34(12):24-26. 被引量:15
  • 5Valiev R Z, Langdon T G. Principles of equal-channel angular pressing as a processing tool for grain refinement[J]. Progress in Materials Science, 2006, 51 : 881-981.
  • 6Furuno K,Akamatsu H, Ohishi K, et al. Microstructural development in equal-channel angular pressing using a 60° die [J]. Acta Materialia, 2004,52(9): 2497-2507.
  • 7Kim H S, Seo M H,Hong S I. Onthediecomcr gap formation in equal channel angular pressing[J]. Materials Science and Engineering, 2000, A 291 : 86-90.
  • 8徐淑波,赵国群.等通道弯角挤压变形机理模拟与工艺参数优化[J].塑性工程学报,2004,11(3):22-26. 被引量:13
  • 9Kim H S. On the effect of acute angles on deformation homogeneity in equal channel angular pressing [J]. Materials Science and Engineering, 2006, A 430: 346-349.
  • 10Nagasekhar A V,Tick-Hon Y, Li S, et al. Effect of acute tool-angles on equal channel angular extrusion/pressing [J]. Materials Science and Engineering, 2005, A410-411 : 269-272.

二级参考文献21

  • 1汪建敏,许晓静,石凤健,姜银方,陈康敏.等径角挤压获得超细晶铜的研究[J].热加工工艺,2004,33(7):6-7. 被引量:25
  • 2李伟,刘平,苏娟华,刘勇,康布熙,田保红.时效与形变对Cu-Cr-Zr合金性能的影响[J].特种铸造及有色合金,2004,24(6):25-26. 被引量:22
  • 3V M Segal, V I Reznikov, A E Drobyshevkiy, et al. Plastic working of metals by simple shear, Russa. Metal. 1981, 115
  • 4Minoru Furukawa, Zenji Horita, Minoru Nemoto.The use of severe plastic deformation for microstructural control, Material Science and Engineering A324, 2002, 82-89
  • 5Y Iwahashi, J Wang, Z Horita, et al. Principle of equal channel-angular ressing for the processing of ultra-fine grained materials, Scripta Metall. 1996,(35): 143-146
  • 6T Altan, Soo-lk Oh, Harold L Gegel, Fasm, Metal forming fundamentals and applications, ASFM,1983, 55-71
  • 7赵国群 马新武.金属塑性成形过程数值模拟软件CASFORM用户使用手册[Z].山东大学,2002..
  • 8Segal V M,Rexnikov V I,Drobyshevskiy A E,et al.Plastic metal working by Simple Shear[J].Russ Metal.,1981,(1):99-105.
  • 9Iwahashi y,Wang J,Horita Z,et al.Principle of equal-channel angular pressing for the processing of ultra-fine grained materials [J].Scripta materialia,1996,35:143.
  • 10Iwahashi Y,Horita Z.Process of grain refinement in equal-channel angular pressing[J].Acta Materilia,1998,46:3317.

共引文献29

同被引文献63

引证文献5

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部