期刊文献+

工艺参数对铝合金双脉冲MIG焊焊缝成形的影响 被引量:49

Influence of processing parameters on weld forming in double-pulse MIG welding of aluminum alloy
下载PDF
导出
摘要 双脉冲MIG焊在进行高效铝焊接的同时可获得美观的鱼鳞纹焊缝表面.在单脉冲稳定焊接的基础上,针对自行开发的双脉冲MIG焊逆变电源,分别改变电流、高频频率、低频频率、焊接速度,进行双脉冲焊接铝合金的试验研究.结果表明,强弱脉冲峰值电流和高频频率对焊接过程的稳定性和飞溅有较大的影响,强弱脉冲峰值电流相差40A,高频频率250Hz时焊缝成形好.在一定范围内,焊缝鱼鳞纹宽度与低频频率、焊接速度直接相关.具体而言,焊缝鱼鳞纹宽度随着低频频率的提高而减小,随着焊接速度的提高而增大,并根据统计规律得出了一个经验公式,用以定量反映这种变动关系.当焊接速度与低频频率比值为0.19~0.30时,鱼鳞纹宽度在2-3mm之间,焊接效果较好. Double-pulse MIG welding of aluminum alloy can improve the efficiency of welding and meanwhile get beautiful weld surface with scaly figures.Based on single-pulse welding,the experiments of double-pulse MIG welding of aluminum alloy were carried out by changing the current,high-frequency,low-frequency and welding velocity of the power which is the self-developed double-pulse MIG welding inverter power.Tests shows that strong/weak pulse peak current and high-frequency have great influence on the stability of welding process and spatters.When the difference between strong and weak pulse peak current is 40 A and high-frequency is 250 Hz,the weld forming is good.To a certain extent,the width of the scaly figure on the weld surface is directly related to low-frequency and welding velocity: the width of the scaly figure will decrease with the improvement of low-frequency and widen with acceleration of welding velocity.An empirical formula reflecting the relationship between low-frequency,welding velocity and the width of the scaly figure through statistical methods is obtained,and the results show that when the ratio of welding velocity to low-frequency is from 0.19 to 0.30,the width of the scaly figure is from 2 to 3 mm,which means good welding performance.
出处 《焊接学报》 EI CAS CSCD 北大核心 2009年第3期69-72,共4页 Transactions of The China Welding Institution
基金 国家自然科学基金资助项目(50875088) 广东省科技计划基金资助项目(2008B010400006)
关键词 双脉冲焊 高频频率 低频频率 焊接速度 鱼鳞纹宽度 double-pulse MIG welding high-frequency low-frequency welding velocity width of the scaly figure
  • 相关文献

参考文献6

  • 1Hirata Y. Pulse arc welding [ J ]. Journal of Japan Welding Society, 2002, 71(3): 115- 130.
  • 2Kuagais M. Recent technological developments in welding of aluminittm and its alloys [J]. Journal of Japan Welding Society, 2002, 71(5): 109 - 114.
  • 3仝红军,上山智之.低频调制型脉冲MIG焊接方法的工艺特点[J].焊接,2001(11):33-35. 被引量:35
  • 4Mendes da Silva C L. Evaluation of the thermal pulsation technique in aluminum welding [ D ]. Brazil: Federal University of Uberlandia, 2003 (in Portuguese).
  • 5Mendes da Silva C L, Scotti A. Theinfluence of doublepulse on porosity formation in aluminum GMAW [ J ]. Journal of Materials Processing Technology 2006, 171 : 366 - 372.
  • 6国旭明,钱百年,杨成刚,等.高强Al-Cu合金脉冲MIG焊工艺研究[C]//熔焊新技术及应用研讨会.江苏无锡,2003:254-258.

共引文献34

同被引文献326

引证文献49

二级引证文献243

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部