期刊文献+

基于有限差分法的动压气体止推轴承静态特性分析 被引量:12

Static Characteristic Analysis of Aerodynamic Gas Thrust Bearing Based on Finite Difference Method
下载PDF
导出
摘要 利用有限差分法对刚性表面和柔性表面两种动压气体轴承的无量纲控制方程进行分析求解,得到了两种轴承在理想支承条件下的压力分布,并由压力分布计算了承载力和摩擦力矩;分析了结构参数对两种轴承静态特性参数的影响。理论分析结果表明:相对于刚性表面气体止推轴承,柔性表面气体止推轴承平台区域的压力分布更加平缓;当柔度较小时,柔性表面动压气体轴承的承载力与刚性表面相当;选取适当的结构参数,可得到理论上的最大承载力以及较小的摩擦力矩。 Finite difference method (FDM) was used to analyze rigid surface gas thrust bearing and compliant surface gas thrust bearing. Pressure distribution for these two bearings was obtained by solving dimensionless governing equations, beating capacity and friction moment were calculated according to the pressure distribution. Effect of structure parameters on static characteristic was discussed. Results of theoretic analysis show that the pressure distribution on plat plane of compliant surface gas thrust bearing is gentler than that of rigid surface gas thrust bearing. If compliance of gas thrust bearing is rather small, the bearing capacity of compliant surface gas thrust bearing equals to that of rigid surface gas thrust bearing. The maximum bearing capacity and smaller friction moment could be obtained with suitable structure parameters.
出处 《润滑与密封》 CAS CSCD 北大核心 2009年第8期6-9,共4页 Lubrication Engineering
基金 新世纪优秀人才支持计划资助项目(NCET-05-0834) 长江学者和创新团队发展计划资助项目(IRT0746)
关键词 气体润滑 止推轴承 承载力 摩擦力矩 有限差分法 gas lubrication thrust bearing bearing capacity friction moment finite difference method
  • 相关文献

参考文献9

  • 1陈纯正 夏祥祖.透平膨胀机的多排切向小孔供气静压气体轴承.西安交通大学学报,1983,17(4):1-7.
  • 2Gray S. Compliant, hydrodynamic bearing with tubular support element :U S,4,213,657 [ P]. 1980.
  • 3Heshmat H. Advanced development of air lubricated foil thrust bearing[ J ]. Lubr Eng, 1984,40 ( 1 ) :21 - 26.
  • 4Heshmat C, Xu D, Heshmat H. Analysis of gas lubricated foil thrust bearing using coupled finite element and finite difference methods [ J]. J Tribol Trans ASME,2000,122 : 199 - 204.
  • 5Teo C J,Spakovszky Z S. Modeling and experimental investigation of mlcro-hydrostatic gas thrust bearings for micro-turbomachines [ J ]. Journal of Turbomachinery, 2006,128 ( 4 ) : 597 - 605.
  • 6Hashimoto H, Ochiai M. Theoretical analysis and optimum design of high speed gas film thrust bearings [ J ]. Transactions of the Japan Society of Mechanical Engineers, 2006,72 (4) :1311 - 1328.
  • 7侯予,赵祥雄,赵红利,陈纯正.弹性支承箔片动压气体径向轴承理论模型的研究[J].润滑与密封,2008,33(6):1-5. 被引量:9
  • 8熊联友,陈纯正,王瑾.平箔动压止推气体轴承的试验研究[J].润滑与密封,2002,27(1):36-37. 被引量:2
  • 9林韶宁,李军,朱朝辉,侯予,陈纯正.新型弹性箔片动压气体止推轴承的试验研究[J].西安交通大学学报,2005,39(7):701-705. 被引量:4

二级参考文献22

  • 1熊联友.新型箔片动压气体推力轴承的研究及其在低温透平膨胀机上的应用,西安交通大学博士学位论文[M].,1998.4.
  • 2柯婉贞 董卫华.新型挠性气体推力轴承研究.第四届全国气体润滑技术交流会论文集[M].,1988..
  • 3[2]H Blok,J J Van Rossum.The foil bearing-a new departure in hydrodynamic lubrication[J].Lubrication Engineering,1993,9 (6):316-320.
  • 4[3]S Gray,H Heshmat,B Bhushan.Technology progress on compliant foil air bearing systems for commercial applications[C].Eighth International Gas Bearing Symposium,Leicester Polytechnic,BHRA Fluid Engineering,Cranfield,Bedford,England,Paper 6,1981:69-97.
  • 5[4]V Castelli,J Pirvics.Review of numerical methods in gas bearing film analysis[J].ASME J Lubr Tech Trans,1969,91:777 -792.
  • 6[5]H Heshmat,J Walowit,O Pinkus.Analysis gas-lubricated compliant journal bearings[J].ASME J Lubr Tech Trans,1983,105 (4):647-655.
  • 7[6]C A Heshmat,H Heshmat.An analysis of gas lubricated multileaf foil journal bearings with backing spring[J].ASME J Lubr Tech Trans,1995,117:437 -443.
  • 8[7]C P Roger Ku,H Heshmat.Structural stiffness and coulomb damping in compliant foil journal bearing:parametric studies[J].STLE Tribol Trans,1994,37 (3):455-462.
  • 9[8]C P Roger Ku,H Heshmat.Structural stiffness and coulomb damping in compliant foil journal bearing:theoretical considerations[J].STLE Tribol Trans,1994,37 (3):525 -533.
  • 10[9]M J Braun,et al.Two-dimensional dynamic simulation of a contianous foil bearing[J].Tribol Int,1996,29:61-68.

共引文献12

同被引文献89

引证文献12

二级引证文献47

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部