期刊文献+

基于差速拧紧的装载机主动锥齿轮预紧力测量方法 被引量:7

Measuring methods of pre-tightening force of loader driving bevel gear based on differential tightening
下载PDF
导出
摘要 该文针对装载机主传动器中主动锥齿轮的预紧问题,研究了主动锥齿轮轴承轴向预紧力与内、外圈轴向相对位移以及预紧力矩的关系,提出以测量容易实现、精度较高的轴承启动摩擦力矩来替代测量较难实现的轴向预紧力,并研制成功了轴承启动摩擦力矩测量的设备。该设备主传动器中锁紧螺母转速比主动锥齿轮略快,利用这一差速拧紧锁紧螺母,逐步地预紧轴承,在对主动锥齿轮进行自动装配的同时,具有自动测量预紧力矩和启动摩擦力矩功能,使主动锥齿轮得到合适的预紧。设备在青岛卡罗拉传动有限公司运行两年多来,降低了工人劳动强度,提高了主传动器的装配质量和效率。 Aiming at the pre-tightening problems of the driving bevel gear of the main transmission device of the loader,the relationship among the bearing axial pre-tightening force of driving bevel gear,the axial relative displacement of the bearing inner and outer ring and the pre-tightening moment,was analyzed.The paper suggested measuring bearing start friction moment,which was easy to achieve and had highly precise,instead of measuring the axial pre-tightening force,which was hard to achieve.The equipment which realized the measuring of the bearing start friction torque had been developed successfully. It could make the rotational speed of the lock nut in the main transmission device a little faster than that of the driving bevel gear, and the differential speed was used to tighten the lock nut and the bearings gradually. It had the function of measuring the pre-tightening moment and the start friction moment automatically at the same time, the driving bevel gear was assembled automatically. The equipment has been put into operation for more than two years, and can relieve the labor intensity and improve the assembling quality and efficiency of the main transmission device.
出处 《农业工程学报》 EI CAS CSCD 北大核心 2009年第9期105-110,共6页 Transactions of the Chinese Society of Agricultural Engineering
基金 安徽省教育厅自然基金(2008AJZR0145)
关键词 锥齿轮 装载机 轴承 预紧力 差速拧紧 bevel gears loaders bearings pre-tightening force differential tightening
  • 相关文献

参考文献19

二级参考文献12

  • 1贾群义.角接触球轴承预紧量的计算及选择[J].轴承,1996(1):5-7. 被引量:9
  • 2杨锦斌,许显存,杨维平,扎西东智,才旦扎西.主轴轴承的预紧及螺母旋紧转矩的实用计算[J].制造技术与机床,2006(9):111-112. 被引量:10
  • 3万长森.滚动轴承的分析方法[M].机械工业出版社,1985..
  • 4黄永录.国外机床主轴轴承[C].洛阳:洛阳轴承研究所,1996..
  • 5戴曙.金属切削机床设计[M].北京:机械工业出版社,1999..
  • 6山田典男等.低力矩圆锥滚子轴承[C].国外汽车轴承,洛阳:洛阳轴承研究所,1992:181—187.
  • 7国家质量技术监督局.静态扭矩测量仪检定规程(JJG995-2005).北京:中国计量出版社,2005
  • 8山洪典男.低力矩圆锥滚子轴承[A].杨金容,译.国外汽车轴承专辑[C].洛阳:洛阳轴承研究所,1992.
  • 9林延中等,掘进机械化设备使用与维护,煤炭工业出版社,1993
  • 10FAG滚动轴承样本(WL41520/3chA).北京:FAG中国有限公司,2002.

共引文献108

同被引文献97

引证文献7

二级引证文献29

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部