期刊文献+

热压原位合成TiC-xNi复合材料的组织与性能 被引量:1

Microstructure and properties of in-situ TiC-xNi composites synthesized by hot-pressing
原文传递
导出
摘要 以钛粉、石墨、钼粉和镍粉为原料,热压原位合成TiC-xNi复合材料。研究碳钛比及镍含量对热压原位合成TiC-xNi复合材料的组织和力学性能的影响。用扫描电镜和X射线衍射仪对复合材料的组织和物相组成进行分析,测试复合材料的致密度、硬度和抗弯强度。结果表明,热压原位合成的碳化物颗粒比较细小,尺寸为0.5-4μm。碳钛比及镍含量对最终产物的相组成没有影响。随碳钛比的增大(从0.9增大到1.0),热压合成TiC-xNi复合材料的组织变得复杂,出现了亮环形组织、亮核/环形结构组织和灰核/环形结构组织,且碳化物颗粒和粘结相的边界平直化。随着镍含量的增加,复合材料的致密度、硬度和抗弯强度都有所降低,碳钛比对复合材料的致密度和硬度影响不大,但抗弯强度随碳钛比的增大明显减小。热压原位合成TiC—xNi复合材料的弯曲断口以沿晶断裂为主,40vol%TiC—Ni复合材料的断口中还出现了一些撕裂棱。 TiC-xNi composites were in-situ synthesized by hot pressing from mixed titanium,graphite,molybdenum and nickel powders.The effects of carbon-titanium ratio and nickel content on microstructure and mechanical properties of TiC-xNi composites were investigated.Microstructure and phases composition of the composites were analyzed by scanning electron microscopy and X-ray diffraction respectively.Relative density,hardness and bending strength were measured.The results show that fine carbide grains with 0.5-4.0 μm are in-situ synthesized by hot pressing.The carbon-titanium ratio and the amount of nickel do not influence the presence of phases in the final products.As the carbon-titanium ratio increases(from 0.9 to 1.0),the microstructure of TiC-xNi becomes complex with bright rims,bright core/rim structure and grey core/rim structure present,moreover,the boundary morphology between the carbide grains and the binder phases changes from an almost rounded shape to an angular shape.Furthermore,the increase of nickel content results in the decrease of relative density,hardness and bending strength.The carbon-titanium ratio has little effect on the relative density and hardness of the composites,while the bending strength decreases with increase of carbon-titanium ratio.The fracture surfaces of the composites are mainly intergranular fracture and some trace of tear ridges can also be found on the fracture surface of 40vol%TiC-Ni composites.
出处 《金属热处理》 CAS CSCD 北大核心 2010年第1期37-42,共6页 Heat Treatment of Metals
基金 国家自然科学基金(10772066) 教育部创新团队项目(IRT0720)
关键词 热压 原位合成 TiC-xNi复合材料 组织 力学性能 hot-pressing in-situ synthesis TiC-xNi composites microstructure mechanical properties
  • 相关文献

参考文献11

  • 1夏明星,胡锐,李金山,薛祥义,王一川,周廉.自生TiC颗粒增强钛基复合材料的研究进展[J].材料导报,2007,21(F05):424-427. 被引量:4
  • 2王子红,,范群成,,顾美转,,肖国庆,,孙巧艳,.Ti2AlC可加工陶瓷自蔓延高温合成中的显微组织演变[J].中国有色金属学报,2004,14(6):990-995. 被引量:10
  • 3栾振涛,周丽,殷凤仕,李树军.SHS-PHIP法制备TiC-Ni(Mo)金属陶瓷[J].热加工工艺,2003,32(6):35-36. 被引量:8
  • 4Yang Y F,Wang H Y,Zhao R Y,et al. Effects of C particle size on the ignition and combustion characteristics of the SHS reaction in the 20wt. % Ni-Ti-C system[ J]. Journal of Alloys and Componds,2008,460 (1/2) :276-282.
  • 5Radhakrishna Bhat B V, Subramanyam J, BhanuPrasad V V. Preparation of Ti-TiB-TiC & Ti- TiB composites by in-situ reaction hot pressing[ J]. Materials Science and Engineering A,2002,325 ( 1/2 ) : 126-130.
  • 6Ni D R, Geng L, Zhang J, et al. TEM characterization of symbiosis structure of in situ TiC and TiB prepared by reactive processing of Ti-B4C[ J]. Materials Letters,2008,62(4/5) :686-688.
  • 7Peng L M, Li Z, Li H, et al. Microstructural characterization and mechanical properties of TiAl-Al2 Ti4 C2 -Al2O3 -TiC in situ composites by hot-press-aided reaction synthesis [ J ]. Journal of Alloys and Compounds ,2006,414(1/2) : 100-106.
  • 8冯志云,黄继华.共沉降-热压法原位反应合成TiC/Ni连续梯度材料[J].粉末冶金技术,2002,20(2):86-89. 被引量:6
  • 9Liu N, Xu Y D, Li Z H, et al. Influence of molybdenum addition on the microstructure and mechanical properties of TiC-based cermets with nano-TiN modification [ J ]. Ceramics International, 2003,29 ( 8 ) : 919- 925.
  • 10何林,黄传真,黄勤,宋世学,王随莲,艾兴.Mo_2C含量对Ti(C,N)基陶瓷力学性能和显微结构的影响[J].材料科学与工程学报,2003,21(2):238-241. 被引量:10

二级参考文献44

共引文献30

同被引文献6

引证文献1

二级引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部