期刊文献+

低中碳高硼铸钢组织和性能的对比研究 被引量:5

Microstructure and Properties of Low and Medium Carbon of High-boron Cast Steel
下载PDF
导出
摘要 借助光学显微镜、透射电镜和X衍射分析仪研究了热处理前后低碳高硼铸钢和中碳高硼铸钢的组织变化;采用一次性摆锤式冲击试验机和ML-10型销盘磨损试验机,将热处理前后的高硼铸钢和高铬铸铁的硬度、冲击韧度和耐磨性进行了对比实验。结果表明,950℃淬火加200℃回火热处理后低碳和中碳高硼铸钢的基体组织转变为板条马氏体,低碳高硼钢硼化物的形态没有明显变化,中碳高硼钢的硼化物发生了断网;热处理后中碳高硼铸钢和低碳高硼铸钢的耐磨性能都有所提高,中碳高硼铸钢热处理后的耐磨性要好于高铬铸铁,低碳高硼铸钢的耐磨性则不如高铬铸铁。 In order to investigate the variety of low carbon high-boron cast steel (LHBS) and medium carbon high-boron cast steel (MHBS) before and after heat treatment, the optical microscopy (OM), transmission electron microscope (TEM) and the X-ray diffraction (XRD) were used in experiment; also rockwell hardness tester, pendulum impact testing machine and ML-10 disk wear testing machine were utilized in this study for testing of corresponding properties. It was found that after water quenched at 950℃ and tempered at 200 ℃, both of MHBS and LHBS's matrix microstructure transform to lath martensite, but the boride form of LHBS does't change significantly and the boride network of MHBS breaks. The wear resistance of both MHBS and LHBS improves remarkably after heat treatment. The wear resistance of MHBS after heat treatment are better than high chromium cast iron, but the wear resistance of LHBS after heat treatment inferior to high chromium cast iron.
出处 《铸造技术》 CAS 北大核心 2010年第1期40-43,共4页 Foundry Technology
关键词 高硼钢 硼化物 热处理 耐磨性 High-boron steel Boride Heat treatment Wear resistance
  • 相关文献

参考文献5

二级参考文献43

  • 1C.S. Liu, S. Y. Chen, Z. T. Wang, B. Yu and Q.K. Cai School of Materials and Metallurgy, Northeastern University, Shenyang 110006, China.MICROSTRUCTURE AND PROPERTIES OF HIGH BORON BEARING STEEL[J].Acta Metallurgica Sinica(English Letters),2002,15(2):248-252. 被引量:8
  • 2符寒光.铸造Fe-B-C合金组织和性能的基础研究[J].铸造,2005,54(9):859-863. 被引量:25
  • 3符寒光,蒋志强.耐磨铸造Fe-B-C合金的研究[J].金属学报,2006,42(5):545-548. 被引量:64
  • 4宋绪丁,蒋志强,符寒光.高硼铸钢的制备与应用[J].铸造技术,2006,27(8):805-808. 被引量:10
  • 5Lakeland K D, Graham E, Heron A. Mechanical properties and microstructures of a series of Fe-Cr-B alloys[R]. The University of Oueensland: Brisbane, Australia, 1992: 1-13.
  • 6Christodoulou P, Calos N. A step towards designing Fe-Cr-B-C cast alloys [J]. Materials Science and Engineering A,2001,A301(2):103-117.
  • 7Calos N J, Graham E, Cousens D R, et al. Mode of boron solubility in ferrous alloys[J]. Materials Transactions, 2001,42(3):496-501.
  • 8Guo Changqing, Kelly P M. Modeling of spatial distribution of the eutectic M2B borides in Fe-Cr-B cast irons[J]. Journal of Materials Science, 2004, 39(3):1109-1111.
  • 9Guo Changqing,Kelly P M.Boron solubility in Fe-Cr-B cast irons [J]. Materials Science and Engineering A,2003,352A(1-2):40-45.
  • 10Lee O S,Han M S, Back J,et al.Damage assessment of composite structures subjected to low velocity impact [J]. Key Engineering Materials, 2004, 261-263(1): 289-294.

共引文献91

同被引文献82

引证文献5

二级引证文献26

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部