期刊文献+

Progress in the application of cold gas dynamic spraying to repairing continuous casting molds 被引量:1

Progress in the application of cold gas dynamic spraying to repairing continuous casting molds
下载PDF
导出
摘要 A new continuous casting mold repairing method--cold gas dynamic spraying (CGDS) is introduced. The study investigates the advantages of the CGDS process regarding repairing operation, such as convenient, in-situ repairation,little heat delivery, microstructural and dimensional stability and other special applications. Microstructure and mechanical properties of the copper alloy coating, nickel coating, ceramic composite coating, and their interface to the substrates ,which are usually used in repairing operation have been researched by means of optical microscopy ( OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and micro-hardness tests. Experimental results have demonstrated the relative density of the copper alloy coating is as high as 98.7%, and that no obvious difference can be observed between the CrZrCu substrate and the Cu alloy coating in terms of microstructures; thus the interface is quite difficult to be identified. The bonding strength and micro-hardness of the Cu alloy coating reach up to 37 MPa and 310 HV0.2 ,respectively. The interface between the copper alloy coating and the nickel coating is either zigzag or wave shaped, and the cohesion is relatively good. As-sprayed nickel coating is dominated by severely deformed particles,and the relative density is up to 98.5%. Complete recrystallization occurred after annealing at 900℃ for one hour,while its micro-hardness remains as high as 124.1 HV02. All these results have indicated that CGDS is a promising technology for repairing the continuous casting mold and that its future development is prosperous as well. A new continuous casting mold repairing method--cold gas dynamic spraying (CGDS) is introduced. The study investigates the advantages of the CGDS process regarding repairing operation, such as convenient, in-situ repairation,little heat delivery, microstructural and dimensional stability and other special applications. Microstructure and mechanical properties of the copper alloy coating, nickel coating, ceramic composite coating, and their interface to the substrates ,which are usually used in repairing operation have been researched by means of optical microscopy ( OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and micro-hardness tests. Experimental results have demonstrated the relative density of the copper alloy coating is as high as 98.7%, and that no obvious difference can be observed between the CrZrCu substrate and the Cu alloy coating in terms of microstructures; thus the interface is quite difficult to be identified. The bonding strength and micro-hardness of the Cu alloy coating reach up to 37 MPa and 310 HV0.2 ,respectively. The interface between the copper alloy coating and the nickel coating is either zigzag or wave shaped, and the cohesion is relatively good. As-sprayed nickel coating is dominated by severely deformed particles,and the relative density is up to 98.5%. Complete recrystallization occurred after annealing at 900℃ for one hour,while its micro-hardness remains as high as 124.1 HV02. All these results have indicated that CGDS is a promising technology for repairing the continuous casting mold and that its future development is prosperous as well.
出处 《Baosteel Technical Research》 CAS 2011年第1期17-23,共7页 宝钢技术研究(英文版)
关键词 cold gas dynamic spraying (CGDS) continuous casting mold repairing COATING MICROSTRUCTURE mechanical property cold gas dynamic spraying (CGDS) continuous casting mold repairing coating microstructure mechanical property
  • 相关文献

参考文献14

  • 1Minami Kenji, Kawata Yoshimasa, Ushio Tetsuji, et al. Method for repairing a mold for continuous ca,;ting of steel : US,4502924 [ P ]. 1985-03 4)5.
  • 2Stoltenhoff T, Kreye H and Richter H J. An analysis of the cold spray process and its coatings[J]. Jotfrnal of Thermal Spray Technology, 2002,11:542-550.
  • 3Ajdelsztajn L,Jodoin B and Schoenung J M. Synthesisand mechanical properties of nanocrystalline Ni coatings produced by cold gas dynamic spraying [J].Surface and Coating Technology,2006,201 ( 3-4 ) : 1166-1172.
  • 4Borchers C, GS.rtner F and Stoltenhoff T. Microstructural and macroscopic properties of cold sprayed copper coatings [J]. J Appl Phys. 2003,93 : 10064-10070.
  • 5Kang Hyun Ki and Kang Suk Bong . Tungsten/copper composite deposits produced by a cold spray [ J ]. Scripta Mater, 2003,49 : 1169-1174.
  • 6Choi H, Yoon S, Kim G, et al. Phase evolutions of bulk amorphous NiTiZrSiSn feedstock during thermal and kinetic spraying processes[J].Scripta Materialia,2005, 53 ( 1 ) : 125-130.
  • 7Shukla V, Elliott G S and Kear B H. Hyperkinetic deposition of nanopowders by supersonic rectangular jet impingement[J]. Scripta Maters,2001,44:2179-2182.
  • 8StoltenhoffT, Borchers C, Gartner F, et al. Micro- structures and key properties of cold-sprayed and thermally sprayed copper coatings [J]. Surface and Coating Technology, 2006,200 ( 16-17 ) :4947 -4960.
  • 9Kim H J, Lee C H and Hwang S Y. Fabrication of WC- Co coatings by cold spray deposition [J] Surface and Coating Technolo~7,2005,191 ( 2-3 ) :335-340.
  • 10ZHANG Huabing,ZHANG Junbao,LIANG Yongli,SONG Hongwei.The effect of annealing treatment on the microstructures and mechanical properties of cold-sprayed nickel coating[J].Baosteel Technical Research,2009,3(2):46-51. 被引量:1

二级参考文献10

  • 1Gartner F,,Stoltenhoff T,Voyer J,et al.Mechanical properties of cold-sprayed and thermally sprayed coatings[ J][].Surface and Coatings Technology.2006
  • 2C-J Li,W-Y Li.Deposition characteristics of titanium coating in cold spraying[].Surface and Coatings Technology.2003
  • 3Hamid Assadi,Frank Gartner,Thorsten Stoltenhoff,et al.Bonding mechanism in cold gas spraying[].Acta Materialia.2003
  • 4Ajdelsztajn L,Jodoin B,Schoenung J M.Synthesis and mechanical properties of nanocrystalline Ni coatings produced by cold gas dynamic spraying[].Surface and Coatings Technology.2006
  • 5Hanshin Choi,,Sanghoon Yoon,Gilyoung Kim,Hyoungho Jo,Changhee Lee.Phase evolutions of bulk amorphous NiTiZrSiSn feedstock during thermal and kinetic spraying processes[].Scripta Materialia.2005
  • 6T. Stoltenhoff,C. Borchers,F. Gtner and H. Kreye.Microstructures and key properties of cold-sprayed and thermally sprayed copper coatings[].Surface and Coatings Technology.2006
  • 7Kim,H.-J.,Lee,C.-H.,Hwang,S.-Y.Fabrication of WC-Co Coatings by Cold Spray Deposition[].Surface and Coatings Technology.2005
  • 8Borchers C,G rtner F,Stoltenhoff T.Microstructural and macroscopic properties of cold sprayed copper coatings[].Journal of Applied Physics.2003
  • 9Borchers C,Gartner F,Stoltenhoff T,et al.Microstruc-tural bonding features of cold sprayed face centered cubic metals[].Journal of Applied Physics.2004
  • 10Borchers,C.,Gartner,F.,Stoltenhoff,T.,Kreye,H.Formation of Persistent Dislocation Loops by Ultra High Strain Rate Deformation During Cold Spraying[].Acta Materialia.2005

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部