期刊文献+

海洋深水立管环缝疲劳性能研究现状及建议 被引量:8

Investigation of fatigue performance of girth weld in deep-water riser pipe
下载PDF
导出
摘要 分析了立管系统类型及其建造方法的基础,讨论了深水立管环缝疲劳性能研究与应用方面的代表性成果。指出,现行的UK BS7608标准对单面焊接环缝惩罚过于严厉,以至不利于采用该技术建造的钢悬链线立管的推广应用,并提出了在深水工程开发中有关立管环缝疲劳研究的若干建议。 Based on the introduction of riser system types and its construction technologies,some representative results about the fatigue performance of girth weld in deep-water riser piper in the past ten years were reviewed,and it was points out that the widely used fatigue design rule of UK BS7608 is overconservative for riser girth welds made from oneside and is not benefit for the application of steel catenary riser.At last,some suggestions about fatigue performance were proposed to study in deep-water development in China.
出处 《焊接》 北大核心 2011年第4期5-10,69,共6页 Welding & Joining
基金 中国海洋石油总公司综合科研项目(CNOOCRC-2009-ZHKY-015) 北京市属高等学校人才强教计划资助项目(PHR201007134)
关键词 深水 立管 环缝 疲劳设计 全尺寸环缝疲劳试验装置 deep-water riser girth weld fatigue design full scale fatigue testing device
  • 相关文献

参考文献13

  • 1Serte O B , Mourelle M M , Grealish F W , et aL Steel catenary riser for the marlim field FPS P-XVIII [C]. Offshore Technology Conference,OTC 8069. Houston Texas, 1996.
  • 2Buitrago J,Zettlemoyer N. Fatigue design of critical girth welds for deepwater applications [C]. The Proceedings of the 17th International Conference on Offshore Mechanics and Arctic Engineering,OMAE98-2004.Houston,Texas,1998.
  • 3Macdonalda K A, Maddoxb S J. New guidance for fatigue design of pipeline girth welds [J]. Engineering Failure Analysis, 2003(10):177-197.
  • 4Netto T A,Botto A, Lourenco M I. Fatigue performance of pre -strained pipes with girth weld defect Local deformation mechanisms under bending [J].Engineering Failure Analysis, 2008,30:1080-1091.
  • 5Netto T A, Lourenco M I, Botto A. Fatigue performance of pre-strained pipes with girth weld defect Full-scale experiments and analyses [J].Engineering Failure Analysis, 2008(30):767-778.
  • 6Maddox S J, Razmjoo G R. Fatigue performance of large girth welded steel tubes [C]. The Proceedings of the 17th International Conference on Offshore Mechanics and Arctic Engineering,OMAE 98-2355. Houston,Texas,1998.
  • 7MaddoxS J, Speck J B, Lockyer S A, et al. Fatigue performance of girth welds made from one side [R]. GSP 5680/26/02, Cambridge : TWI, 2002.
  • 8Salama M M. Fatigue design of girth welded pipes and the validity of using strips [C]. Proceedings of 18th International Conference on Offshore Mechanics and Arctic Engineering, OMAE99-2003.St. Johns, Newfoundland,Canada, 2003.
  • 9Connelly L M, Zettlemoyer N. Stress eoncentrations at girth welds of tubulars with axial wall misalignment [C]. Proceedings of the Fifth International Symposium on Tubular Struetures.UK, 1993.
  • 10Leggatt R H. Residual stresses in girth welds in pipes[C]. WIC/ISC International Conference Welding in Energy Related Projects.Toronto, Canada,1983.

同被引文献75

引证文献8

二级引证文献32

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部