期刊文献+

PCD刀具高速铣削SiC_p/Al复合材料切削温度试验研究 被引量:10

Experimental Study on Temperature during High Speed Milling of SiC_p/Al Composites Using PCD Tool
下载PDF
导出
摘要 采用夹丝半人工热电偶法,在600-1200m/min速度范围内对PCD刀具高速铣削SiCp/2009Al复合材料时的切削温度进行了研究,采用单接点热电偶快速标定装置对热电偶(SiCp/2009Al—康铜)测量的热电势进行了标定试验,获得了各种复合材料的温度标定曲线。研究结果表明,在本文试验条件下,铣削温度瞬时最高值可达519℃,切削参数对切削温度影响程度由大到小依次是:切削速度、增强颗粒体分比、径向切宽、每齿进给量。 High-speed mining tests were performed on SiCp/2009A1 composites in the speed range of 600 - 1200m/min using PCD tools to investigate the cutting temperatures and the influence factors. Using single-contact-point high-speed thermocouple cali- bration eqtripment,the electromotive force-cutting temperature curves were obtained. The results show that the maximum cutting temperature can reach 519℃ under the given cutting conditions. Among these cutting parameters, cutting speed is the most significant factor. Reinforcement volume fraction is the less significant factor and followed by radial depth of cut and feed rate.
出处 《工具技术》 2011年第8期31-35,共5页 Tool Engineering
基金 国家高技术发展研究计划(863)(2009AA04Z116) 江苏省高校自然基金资助项目(09KJB460004) 南京工程学院科研启动基金资助项目(KXJ08024)
关键词 颗粒增强铝基复合材料 高速铣削 PCD刀具 切削温度 热电势标定 particle reinforced aluminum composites high-speed milling PCD tool cutting temperature thermocouple calibration
  • 相关文献

参考文献10

  • 1Miracle D B. Metal matrix composites-from science to techno- logical significance [ J]. Composites Science and Technology, 2005, 65: 2526-2540.
  • 2M El-Gallab, M SHad. Machining of Al/SiC particulate metal- matrix composites Part I: tool performance [J]. Materials Pro- cessing Technology, 1998, 83: 151- 158.
  • 3Caroline J E Andrewes, His-Yung Feng, W M Lau. Machining of an aluminum/SiC composite using diamond inserts[J]. Mate- rials Processing Technology, 2000, 102:25 - 29.
  • 4Xu Jiuhua, Zuo Dunwen, Yang Mingda, et al. Machining of metal matrix composites [ J ]. Transactions of NUAA, 1995, 12 (2) : 161 - 167.
  • 5Y F Ge, J H Xu, H Yang, et al. Workpiece surface quality when ultra-precision turning SiCp/Al composites [ J]. J. Mater. Pro- cess. Technol. ,2008, 203: 166-175.
  • 6Ge Yingfei, Xu Jiuhua, Yang Hui. Diamond tools wear and their applieability when ultra-precision turning of SiCp/2009Al matrix eomposite[J] .Wear, 2010, 269: 699-709.
  • 7吴震宇,简小刚,孙方宏,刘国良,陈明.SiC颗粒增强铝基复合材料高速铣削实验研究[J].机械工程师,2003(8):14-17. 被引量:2
  • 8韩荣第,李汉国.SiC_p/Al、SiC_w/Al复合材料加工的切削温度与刀具磨损的试验研究[J].宇航材料工艺,1997,27(3):36-39. 被引量:8
  • 9卢接驰,全燕鸣,徐昊.绿色切削SiC_p/Al复合材料的刀具温度研究[J].工具技术,2009,43(2):12-15. 被引量:1
  • 10YR Kevin Chou, Jie Liu. CVD diamond tool performance in metal matrix composite machining [ J ]. Surface & Coatings Technology, 2005, 200: 1872-1878.

二级参考文献16

  • 1韩荣第,吴健.绿色切削技术探讨[J].工具技术,2006,40(12):8-10. 被引量:22
  • 2刘光复,刘志峰,李钢.绿色设计与绿色制造.北京:机械工业出版社,2007.
  • 3Y Sahin. Preparation and some properties of SiC particle reinforced aluminum alloy composites. Materials and Design, 2003 (24) : 671 -679
  • 4C T Wlyne, P J Withers. An introduction to metal matrix composites. London: Cambridge Universty Press, 1993
  • 5S Ramrattan, F Sitkins, M Nallakatala. Opimization of the casting and machining processes for metal-matrix composites. In: Processing of the Canadian Socity Machancial English Symposim. McMaster University, 1996:624 - 629
  • 6H A Kishawy, M Dumitrescu, E G Ngb, et al. Effect of coolant strategy on tool performance, chip morphology and surface quality during high-speed machining of A356 aluminum alloy. International Journal of Machine Tools & Manufacture, 2005, 45:219 - 227
  • 7U B Durval. Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminum-silicon alloys. Journal of Materials Processing Technology, 2002, 122:127-138
  • 8F Itoigawa, C Childs, T Nakamuraa, et al. Effects and mechanisms in minimal quantity lubrication machining of an aluminum alloy. Wear, 2005,260: 339 - 344
  • 9J. M. Torralba, C. E. da Costa, et al. P/M aluminum matrix composites: an overview[ J ]. Journal of Materials Processing Technology 133 (2003).
  • 10Zhang Hong. Plastic deformation and chip formation mechanisms during machining of copper,aluminum and an aluminum matrix composite[ D ]. The University of Windsor, Canada, 2000.

共引文献8

同被引文献109

引证文献10

二级引证文献18

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部