期刊文献+

9Ni钢薄板的奥氏体化温度及强韧化因素分析 被引量:11

Austenitizing Temperature for 9Ni Steel Thin Plate and Analysis of Strengthening and Toughening Factors
原文传递
导出
摘要 研究了奥氏体化温度对9Ni钢薄板组织性能的影响,并分析了薄板与厚板低温韧性差异的原因。奥氏体化温度高于800℃后,随着奥氏体化温度升高,奥氏体化温度对逆转奥氏体(γ′)的体积分数没有影响;奥氏体化后奥氏体晶粒尺寸减小,晶粒趋于等轴;组织均匀化程度提高;最终组织中取向差大于1 5°区域尺寸减小,低温韧性增加;板条或亚板条束的平均尺寸增加,强度降低。薄板中较小的平均取向差是其低温韧性较低的主要原因。 Influence of austentizing temperature on microstructure and properties of 9Ni steel thin plate was investigated and the causes for inferior cryogenic toughness compared to heavy plate was analyzed.As the austenitizing temperature increased from 800 to 900℃,the volume fraction of reversed austensite was unchanged.The austensite grain size decreased and tended to be equiaxed.The uniformity of microstructure was improved.The cryogenic toughness increased as the zone size decreased which surrounded by higher than 15°misorientation grain boundary.The yield strength decreased as sub-block or lath mean size increased.The lower cryogenic toughness of thin plate was mainly attributed to the less average misorientation.
出处 《钢铁研究学报》 CAS CSCD 北大核心 2011年第9期37-41,共5页 Journal of Iron and Steel Research
基金 国家高技术研究发展计划资助项目(2007AA03Z504)
关键词 9NI钢 奥氏体化温度 低温韧性 EBSD 回火马氏体 9Ni steel austenitizing temperature cryogenic toughness EBSD tempered martensite
  • 相关文献

参考文献8

  • 1刘彦明,石凯,周勇,李国明,王志强.9Ni钢的热处理及低温韧度[J].热加工工艺,2007,36(16):77-79. 被引量:42
  • 2Sangho Kim, Sunghak Lee, Bong Sang Lee. Characterization of Boundaries and Determination of Effective Grain Size in Mn- Mo-Ni Low Alloy Steel From the View of Misorientation [J]. Scripta Mater, 2000,43 : 205.
  • 3Schino A D, Guarnaschelli C. Effect of Microstructure on Cleavage Resistance of High Strength Quenched and Tempered Steels [J]. Materials Letters, 2009,63 (22) : 1968.
  • 4Kawata H, Sakamoto K, Moritani T, et al. Crystallography of Ausformed Upper Bainite Structure in Fe-gNi-C Alloys [J]. Materials Science and Engineering,2006A(438/440) :140.
  • 5Takuya Hara, Naoki Maruyama, Yasuhiro Shinohara, et al. Abnormal a to 7 Transformation Behavior of Steels With a Martensite and Bainite Microstructure at a Slow Reheating Rate [J]. ISIJ International,2009,49(11) : 1792.
  • 6Morito S, Yoshida H, Maki T. Effect of Block Size on Strength of Lath Martensite in Low Carbon Steels [J]. Materials Science and Engineering,2006A(438/440) :237.
  • 7Krauss G. Martensite in Steel: Strength and Structure [J]. Materials Science and Engineering,1999A(273/275):40.
  • 8WANG Chun-fang, WANG Mao-qiu, SHI Jie, et al. Effect of Microstrustural Refinement on the Toughness of Low Carbon Martensite Steel [J]. Scripta Materialia, 2008,58 : 492.

二级参考文献14

  • 1张弗天,楼志飞,叶裕恭,李端义.Ni9钢的显微组织在变形-断裂过程中的行为[J].金属学报,1994,30(6). 被引量:20
  • 2李光来,孟祥敏,张弗天,吴玉琨.Ni9钢微观结构的TEM研究[J].金属学报,1996,32(11):1121-1129. 被引量:4
  • 3中国机械工程学会焊接学会.焊接手册(材料的焊接)[M].北京:机械工业出版社,1992.335-337.
  • 4ASTM A553/A553M-95.Standard specification for pressure vessel plates, alloy steel, quenched and tempered 8 and 9 percent nickel[ S ].
  • 5张弗天 王景韫 郭蕴宜.Ni9钢中的回转奥氏体与低温韧性.金属学报,1984,20(6):405-410.
  • 6Syn C K, Fultz B,Morris J W.Mechanical stability of retained austenite in tempered 9Ni steel [J].Metallurgical Transaction (Physical Metallurgy and Materials ),1978,9A(1): 1635-1640.
  • 7Mchenry H I,Richard P R,Alan F C,et al . Material at low temperature american society for metals [M].USA:American Society for Metals, 1983.478-512.
  • 8Norstrom L A.Influence of austenitizing and tempering treatment on microstructure, yield strength and impact toughness of a martensitic 9%Ni steel [J]. Scandinavian Journal of Metallurgy, 1976,5 (1):41-48.
  • 9肖纪美.金属的韧性与韧化[M].北京:科学出版社,1976.
  • 10陈继勤 程怡萱 卜万龙 等.9%Ni低温钢的回火相变.浙江大学学报:工学版,1980,(1):5-8.

共引文献41

同被引文献149

引证文献11

二级引证文献37

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部