期刊文献+

抽拉速率对定向凝固Ni-45Ti-5Al合金微观组织的影响 被引量:4

Effect of withdrawal rate on microstructure of directionally solidified Ni-45Ti-5Al alloys
下载PDF
导出
摘要 采用Bridgman型液态金属冷却定向凝固方法,研究Ni-45Ti-5Al(摩尔分数,%)合金在不同抽拉速率(20、100和200μm/s)下定向凝固后的相组成及其形态特征。结果表明:Ni-45Ti-5Al合金定向凝固生长区呈现明显的柱状晶生长形态,定向效果良好,NiTi基体以[100]方向为择优取向,Ti2Ni析出相沿[111]晶向择优生长。随着抽拉速率的提高,Ti2Ni相更加细小、分散,由在胞晶界上几乎连续分布改变为断续分布。在20~200μm/s的宽生长速率范围内,均以胞状晶形态生长,固/液界面形态没有发生显著变化;随着抽拉速率从20μm/s增加到200μm/s,定向胞晶组织明显细化,平均胞晶间距由85μm减小到25μm。 The phase compositions and shapes of directionally solidified(DS) Ni-45Ti-5Al(mole fraction,%) alloys were investigated in the Bridgman liquid-metal-cooling directional-solidification process at withdrawal rates of 20,100 and 200 μm/s.The results show that the columnar grain growth is observed in the DS specimens.The preferred crystal orientation of NiTi matrix is direction and that of Ti2Ni phase precipitated on the matrix is direction.With the increase of withdrawal rate,the Ti2Ni phase becomes finer and distributes from continuously to discontinuously in the intercellular region.When the withdrawal rate varies from 20 μm/s to 200 μm/s,all the solid/liquid interface morphologies are cellular,the DS microstructure is refined obviously and the cellular spacing decreases from 85 μm to 25 μm.
出处 《中国有色金属学报》 EI CAS CSCD 北大核心 2011年第11期2763-2768,共6页 The Chinese Journal of Nonferrous Metals
关键词 Ni-45Ti-5Al合金 定向凝固 微观组织 固/液界面 Ni-45Ti-5Al alloy directional solidification microstructure solid/liquid interface
  • 相关文献

参考文献13

  • 1WARREN P, MURAKAMI Y, KOIZYMI Y, HARADA H. Phase separation in NiTi-Ni2TiAl alloy system[J]. Materials Science and Engineering A, 1997, 223: 17-20.
  • 2KOIZUMI Y, RO Y, NAKAZAWA S, HARADA H. NiTi-base intermetallic alloys strengthened by Al substitution[J]. Materials Science and Engineering A, 1997, 223:36- 41.
  • 3孟令杰.NiTi-Al高温结构材料的研究[D].北京:北京航空航天大学.2006.
  • 4MENG L J, LI Y, ZHAO X Q, XU H B. The mechanical properties of intermetallic Ni50-xTi50Alx alloys (x=6, 7, 8, 9)[J]. Intermetallics, 2007, 15: 814-818.
  • 5XU H B, MENG L J, XU J, LI Y, ZHAO X Q. Mechanical properties and oxidation characteristics of TiNiAl(Nb) intermetallics[J]. Intermetallics, 2007, 15: 778-782.
  • 6孟令杰,李岩,赵新青,徐惠彬.Nb对富钛TiNiAl金属间化合物强化机制的影响[J].航空学报,2007,28(5):1206-1209. 被引量:17
  • 7傅恒志,郭景杰,苏彦庆,刘林,徐达鸣,李金山.TiAl金属间化合物的定向凝固和晶向控制[J].中国有色金属学报,2003,13(4):797-810. 被引量:40
  • 8张花蕊,高明,唐晓霞,张虎.定向凝固过程中Ti-47Al-2Cr-2Nb合金与Y_2O_3陶瓷的相互作用[J].金属学报,2010,46(7):890-896. 被引量:18
  • 9HUNEAU B, ROGL P, ZENG K, SCHMID-FETZER R, BOHN M, BAUER J. The ternary system Al-Ni-Ti. Part I : Isothermal section at 900 ℃ experimental investigation and thermodynamic calculation[J]. Intermetallics, 1999, 7: 1337-1345.
  • 10ZENG K, SCHMID-FETZER R, HUNEAV B, ROGL P, BAUER J. The ternary system Al-Ni-Ti. Part II: Thermodynamic assessment and experimental investigation of polythermal phase equilibria[J]. Intermetallics, 1999, 7: 1347-1359.

二级参考文献34

  • 1许雄,沈军,彭桂林,郑循强,丁宏升.γ-TiAl基合金定向凝固特性研究[J].材料导报,2005,19(6):105-107. 被引量:1
  • 2陈国良 林均品.有序金属间化合物结构材料[M].北京: 冶金工业出版社,1998.35-38.
  • 3Loria E A. Interrnetallics, 2000; 8:1339.
  • 4Inui H, Oh M H, Nakmura A. Acta Metall, 1992; 40:3095.
  • 5Kishida K, Johnson D R, Masuda Y. Intermetallics, 1998; 6:679.
  • 6Jung I S, Kim M C, Lee J H. Interrnetallics, 1999; 7:1247.
  • 7Johnson D R, Masuda Y, Inui H, Yamaguchi M. Mater Sci Eng, 1997; A239-240:577.
  • 8Johnson D R, Chihara K, Inui H, Yamaguchi M. Acta Mater, 1998; 46:6529.
  • 9Lapin J, Ondrus L. Kovove Mater, 2002; 40:161.
  • 10Kim M C, Oh M H, Lee J H, Inui H, Yamaguchi M, Wee D M. Mater Sci Eng, 1997; A239-240:570.

共引文献67

同被引文献47

引证文献4

二级引证文献5

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部