期刊文献+

基于Dynaform的油底壳一次拉深成形探究

Base on Dynaform's Automobile Engine Oil Pan for One-step Drawing Exploration and Research
下载PDF
导出
摘要 采用ETA/Dynaform对发动机油底壳进行了有限元拉深模拟,探讨一次性拉深成形的可行性,设计了两种方案进行冲压模拟,任意选取会破裂的节点,跟踪其运动轨迹,并且得到其在X、Y、Z方向上从冲压开始到结束的应力曲线图,通过观测节点所处的区域在破裂一瞬间的应力图,得知使零件破裂的应力为该节点Z方向的应力,并且据此给出二次拉延成形的初步方案。 In this paper,ETA/Dynaform was used for CN100 engine oil pan finite element simulation,To seeking maximize the benefits and explore the feasibility,two one-step drawing strategies were proposed,A node were picked randomly at the cracking region.According to the moving trace of the node,stress curves of three directions were obtained during the whole forming process.It was found that the stress stress causing cracking in the two sides came from Z direction of the nodes.and according to this can find the initial strategie of two-step drawing.
出处 《装备制造技术》 2012年第5期21-23,共3页 Equipment Manufacturing Technology
关键词 油底壳 一次拉深 数值模拟 CN 100 oil pan one-step drawing simulation
  • 相关文献

参考文献6

  • 1龚红英,何丹农,张质良.计算机仿真技术在现代冲压成形过程中的应用[J].锻压技术,2003,28(5):35-38. 被引量:21
  • 2汪锐,罗亚军,郑晓丹,何丹农.复杂零件多道次拉深成形的计算机仿真[J].塑性工程学报,2001,8(2):17-19. 被引量:13
  • 3J Woodthorpe, R Pearce. The Anomalous Behavior of Aluminum sheets under Balanced Biaxial Tension [J].Intemational Journal of Mechanical Science, 1970, (12) : 341-360.
  • 4R Hill. Plasticity Theory of Textured Aggregates [J]. Proceeding of Camb. Phil., 1979, (85) : 150-179.
  • 5彭颖红.金属塑性成形数值模拟技术[M].上海:上海交通大学出版社,1999.
  • 6钟志华,李光耀,等.薄板冲压成型过程的计算机数值模拟与应用[M].北京:北京理工大学出版社,1998.

二级参考文献3

  • 1王勖成 邵敏.有限单元法基本原理与数值方法[M].清华大学出版社,1998..
  • 2钟志华,薄板冲压成形过程的计算机仿真与应用,1998年
  • 3卫原平,夏欣,冯建华,钟卫龙.多工步板料成形过程的计算机仿真[J].上海交通大学学报,1999,33(2):244-246. 被引量:9

共引文献31

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部