期刊文献+

连续螺旋折流板换热器流动与传热性能及熵产分析 被引量:17

Analyses on flow and heat transfer performance and entropy generation of heat exchanger with continuous helical baffles
下载PDF
导出
摘要 采用数值模拟的方法,研究了螺旋角对连续螺旋折流板换热器流动与传热性能的影响,并以熵产数为指标对换热器性能进行了基于热力学第二定律的分析评价。结果表明,相同质量流量时壳程传热系数和压降均随螺旋角的增大而降低,且后者降低的幅度大于前者。连续螺旋折流板换热器壳程横截面上切向速度分布较弓形折流板换热器更加均匀。在靠近中心假管的内层区域,同一径向位置的轴向速度随螺旋角的增大而降低,而在靠近壳体壁面的外层区域则相反。螺旋角越大,不同径向位置的换热管间的换热量分布均匀性越好。壳程质量流量相等时,换热器中传热引起的熵产占总熵产的比重随着螺旋角的增大而增加,熵产数随着螺旋角的增大而降低。 A numerical simulation for heat exchanger with continuous helical baffles was carried out by using commercial codes of ANSYS CFX 12.0.The study focuses on the effects of helix angle on flow and heat transfer characteristics,and heat exchanger performance is evaluated by entropy generation number based on the analysis of the second law of thermodynamics.The results show that both the shell-side heat transfer coefficient and pressure drop decrease with the increase of the helix angle at certain mass flow rate.The latter decreases more quickly than the former.The tangential velocity distribution on shell-side cross section is more uniform with continuous helical baffles than with segmental baffles.The axial velocity at certain radial position decreases as the helix angle increases in the inner region near the central dummy tube,whereas it increases as the helix angle increases in the outer region near the shell.The heat exchange quantity distribution in tubes at different radial positions is more uniform at larger helix angle.The proportion of the entropy generation contributed by heat transfer in total entropy generation increases and the entropy generation number decreases with the increase of the helix angle at certain mass flow rate.
出处 《化工学报》 EI CAS CSCD 北大核心 2012年第8期2375-2382,共8页 CIESC Journal
基金 国家自然科学基金项目(51106090)~~
关键词 连续螺旋折流板 换热器 螺旋角 熵产 数值模拟 continuous helical baffles; heat exchanger; helix angle; entropy generation; numerical simulation
  • 相关文献

参考文献19

  • 1Bell K. Heat exchanger design for the process industries[J]. JournalofHeat Transfer, 2004, 126 (6).. 877-885.
  • 2Wang Qiuwang, Chen Guidong, Chen Qiuyang, Zeng Min. Review of improvements on shell-and-tube heat exchangers with helical baffles [J]. Heat Transfer Engineering, 2010, 31 (10): 836-853.
  • 3Lutcha J, Nemcansky J. Performance improvement of tubular heat exchangers by helical baffles [J]. Chemical Engineering Research and Design, 1990, 68 (A) : 263- 270.
  • 4汲水,杜文静,程林.连续螺旋折流板换热器壳侧传热与流动特性的数值研究[J].中国电机工程学报,2009,29(32):66-70. 被引量:12
  • 5Lei Yonggang, He Yaling, Li Rui, Gao Yafu. Effects of baffle inclination angle on flow and heat transfer of a heat exchanger with helical baffles [J]. Chemical Engineering and Processing, 2008, 47 (12): 2336-2345.
  • 6陈世醒,张克铮,张强.螺旋折流板换热器的开发与研究(Ⅰ)——高粘度流体下的中试研究[J].抚顺石油学院学报,1998,18(3):31-35. 被引量:52
  • 7朱冬生,蒋翔.管壳式换热器壳程高黏度流体的传热强化[J].化工学报,2005,56(8):1451-1455. 被引量:8
  • 8Zhang Jianfei, Li Bin, Huang Wenjiang, Lei Yonggang, He Yaling, Tao Wenquan. Experimental performance comparison of shell-side heat transfer for shell-and-tube heat exchangers with middle-overlapped helical baffles and segmental baffles [J]. Chemical Engineering Science, 2009, 64 (8): 1643-1653.
  • 9曹兴,杜文静,汲水,程林.搭接方式对螺旋折流板换热器壳程性能的影响[J].化工学报,2011,62(12):3367-3372. 被引量:15
  • 10Lei Yonggang, He Yaling, Chu Pan, Li Rui. Design and optimization of heat exchangers with helical baffles [J]. Chemical Egineering Science, 2008, 63 (17) :4386-4395.

二级参考文献38

共引文献110

同被引文献167

引证文献17

二级引证文献60

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部