期刊文献+

基于ABAQUS的岩石滚刀实验机最优刀间距分析 被引量:12

Optimal Analysis for Cutter Space of Linear Cutter Machine Based on ABAQUS
下载PDF
导出
摘要 目的利用有限元软件ABAQUS模拟岩石滚刀实验机破岩机理来确定最优刀间距.方法建立了双滚刀岩石实验机的有限元模型,分析了岩石滚刀实验机的破岩机理、破岩中比能变化过程.结果滚刀切削岩石时,比能随着滚动长度的增大而增加,当滚动长度达到100 mm后,比能值基本稳定.比能值随着滚刀间距的增大先降低后增大,滚刀间距为50 mm时,比能值最小,随后比能值随滚刀间距增大而增大,直到滚刀间距达到70 mm后,比能值基本稳定.结论 50 mm是本模拟实验滚刀间距最佳值,此时两把滚刀形成的破碎区贯通,且整个破碎区最大,比能值最小. In this paper, finite element software ABAQUS is used to simulate a proc, ess of the linear cutter machine, and to analyze fragmentation process of the rock and confirmed the optimal cutter space. According to the simulated results, it is shown that special energy (SE) decreases first and then increases following. When disc cutter cutting rock, SE with the increase of rolling length increases until the rolling length up to 100 mm,and then SE remained stable. SE with cutter spacing increases first decreased and then increased. The cutter space decrease until the cutter space reach 70 mm, then SE value obtain basic stability. SE considerations indicate that a spacing of 50 mm is close to optimum in this hard brittle crystalline rock. The 50 mm cutter space which two cutters fragmentation zone is interconnected and SE value reach low, has the optimal value in this simulation study. The research has certain reference value to optimize cutter system and to understand rock fragmentation theory for the boring tunnel project.
出处 《沈阳建筑大学学报(自然科学版)》 CAS 北大核心 2012年第5期927-931,共5页 Journal of Shenyang Jianzhu University:Natural Science
基金 国家十二五计划项目(2011BAJ02B05-5) 辽宁省教育厅重点实验室项目(LS2010129) 辽宁省教育厅创新团队项目(LT2010087) 住房和城乡建设部项目(2011-k8-8) 三向旋转测力仪在TBM滚刀滚压岩石机理研究中应用服务项目(F10-234-4-00)
关键词 全断面岩石掘进机 盘形滚刀 破岩 有限元模型 ABAQUS TBM disk cutter rock fragmentation FEA model ABAQUS
  • 相关文献

参考文献13

  • 1张羽.隧道掘进机(TBM)在工程施工中的应用[J].科技情报开发与经济,2005,15(3):290-291. 被引量:3
  • 2Gong Qiuming, Zhao Jian, Jiao Yuyong. Numerical modeling of the effects of joint orientation on rock fragmentation by TBM cutters [ J ]. Tunneling and Underground Space Technology,2005,20 ( 2 ) : 183 - 191.
  • 3Liu H Y, Kou S Q, Lindqvist P A, et al. Numerical simulation of the rock fragmentation process induced by indenters [J]. Int. J. Rock Mech. Min. Sci, 2002, 39(4) :491 -505.
  • 4Gertscha R, Gertschb L, Rostamic J. Disc cutting tests in colorado red granite: implications for TBM performance prediction [ J ]. International Journal of Rock Mechanics & Mining Sciences ,2007,44:238 - 246.
  • 5Kasper T,Meschke G. On the influence of face pres- sure, grouting pressure and TBM design in soft ground tunnelling [ J ]. Tunnelling and Underground Space Technology, 2006,21 : 160 - 171.
  • 6Movinkel T, Johannessen O. Geological parameters for hard rock tunnel boring [ J ]. Tunneling and Underground Space Technology, 1994,9 ( 4 ) : 425 - 437.
  • 7谭青,屠昌锋,暨智勇,夏毅敏.盘形滚刀切割岩石的数值仿真[J].现代制造工程,2009(2):62-64. 被引量:17
  • 8Fruguglietti A, Guglielmetti V, Grasso P, et al. Selection of the right TBM to excavate weathered rocks and soils [J]. Proceedings AITES/ITA World Tunnel Congress, 1999 : 839 - 847.
  • 9Gertscha R. Gertschb L. Rostamic J. Disc cutting tests in colorado red granite: implications for TBM performance prediction [ J ]. International Journal of Rock Mechanics & Mining Sciences ,2007,44:238 - 246.
  • 10张珂,王贺,吴玉厚,赵凯军.全断面硬岩TBM滚刀磨损关键技术分析[J].沈阳建筑大学学报(自然科学版),2009,25(2):351-354. 被引量:13

二级参考文献20

共引文献115

同被引文献105

引证文献12

二级引证文献64

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部