期刊文献+

基于LabVIEW的微机械陀螺动态参数的测试 被引量:3

Dynamic Parameters Test of Micro-Machined Gyroscope Based on LabVIEW
下载PDF
导出
摘要 针对当前测试微机械陀螺动态参数存在耗时长、效率低等缺点,提出了一种新的测试陀螺动态参数的方法,该方法通过Lab-VIEW编写的测试软件控制一数据采集卡和信号调理电路激励陀螺振动并采集其驱动方向上的振动数据,从采集的振动数据中提取出波峰和波谷进行指数拟合获取陀螺的衰减系数和固有频率,最后根据阻尼振动方程计算出陀螺的阻尼比和谐振频率,同时获取陀螺的品质因子;该方法能够实现自动记录和处理陀螺的振动数据;整个测试过程只需15s左右,提高了测试效率;利用该方法测试了30种不同气压下陀螺的品质因子,得到的陀螺的品质因子与气压值的关系曲线和理论研究结果相符,从而为陀螺动态参数的测试提供了一种有效的手段。 For the current method test dynamic parameters of Micro--machined Gyroscope has some defects, such as time--consuming and low efficiency, a new method test dynamic parameters of gyroscope is put forward in this paper, this method control a data acquisition card and signal regulate circuit to drive gyroscope vibrate and collect the vibration data on the drive direction of gyroscope by a test software written in the LabVIEW, then extract peaks and troughs from the vibration data to get the attenuation coefficient and the inherent frequency of gyroscope through index fitting, finally calculated the damping ratio and the resonant frequency of gyroscope according to the damping vi- bration equation and get the quality factor at the same time. The method can realize recording and processing the vibration data of gyroscope automatieally. Tb.e entire testing process takes about 15 seeortds, so this method has improved the test efficiency. Using this method tested the quality factor of the gyroscope in 30 different pressure, the relation curve of quality factor and the pressure value is conform to the theo retical results, thus this paper provide an effective means for the dynamic parameter test of gyroscope.
出处 《计算机测量与控制》 北大核心 2013年第3期580-582,585,共4页 Computer Measurement &Control
基金 航空科学基金(20110868001)
关键词 LABVIEW 微机械陀螺 阻尼比 谐振频率 品质因子 LabVIEW micro--machined gyroscope damping ratio resonant frequency quality factor
  • 相关文献

参考文献10

二级参考文献38

共引文献29

同被引文献25

  • 1GAISSERAlexander GAOZhong-yu ZHANGRong CHENZhi-yong ZHOUBin.ON-LINE SELF-TESTING FOR MICRO-MACHINED GYROSCOPES[J].Transactions of Nanjing University of Aeronautics and Astronautics,2005,22(2):98-102. 被引量:2
  • 2李锦明,张文栋,李林.电容式微机械陀螺品质因子测试方法研究[J].中北大学学报(自然科学版),2006,27(4):357-360. 被引量:6
  • 3吕家才,周春天,刘明明,孙小鹏.梁长对悬臂梁振动测定材料动弹性模量的影响[J].河海大学学报(自然科学版),2006,34(5):561-563. 被引量:12
  • 4王晓艳,王海峰.基于多频声信号的虚拟扫频仪的设计与实现[c]//全国电工理论与新技术学术年会论文集.西安:中国电工技术学会,2004:229-232.
  • 5Li Yuxuan, Lin Zhongqin, Jiang Aiqin, et al. Experimental study of glass-fiber mat thermoplastic material impact properties and lightweight automobile body analysis[J]. Materials and Design, 2004,25:579-585.
  • 6Dasappa P, Lee-Sullivan P, Xiao Xinran. Temperature effects on creep behavior of continuous fiber GMT composites[J]. Composites:Part A, 2009,40:1 071-1 081.
  • 7Yim H S J, Cho Y, Seo Y J, et al. A study on material damping of 0° laminated composite sandwich cantilever beams with a viscoelastic layer[J]. Composite Structures, 2003,60:367-374.
  • 8Jean-Marie B. Damping analysis of laminated beams and plates using the ritz method[J]. Composite Structures, 2006,74:186-201.
  • 9Suzuki K, Kazuro K, Isao K, et al. Vibration and damping pre diction of laminates with constrained viscoelastic layers-numerical analysis by a multilayer higher-order-deformable finite element and experimental observations[J]. Meeh Adv Mater Struct,2003, 10(1):43-75.
  • 10刘忠卿,张嵘.微机械陀螺管芯测试方法[J].传感器与微系统,2008,27(4):111-113. 被引量:2

引证文献3

二级引证文献8

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部