期刊文献+

热挤压、固溶及时效对Al-Cu-Mn铝合金微观金相组织的影响 被引量:7

Effect of Hot Extrusion,Solution and Aging Treatment on Microstructure of Al-Cu-Mn Aluminum Alloy
原文传递
导出
摘要 将Al-Cu-Mn铝合金热挤压加工成棒材,然后对其进行固溶淬火处理以及在175℃下进行不同时间的时效处理,研究了热挤压、固溶淬火以及时效等对该合金微观组织的影响。结果表明:热挤压后,没有铸态下的大晶粒存在,且晶界也不明显,脆硬相被挤碎,在T相附近有再结晶晶粒出现,这些微观结构均沿挤压变形方向排列;固溶淬火后,T相弥散析出,挤压变形后的微观金相组织仍然存在,未固溶脆硬相的数量和尺寸均有所减小,但再结晶晶粒尺寸增大,同时出现了一些新的尺寸细小的再结晶晶粒;时效处理对微观金相组织的影响不大。 Al-Cu-Mn alloy was hot-extruded into bar and then given a solution and quenching treaanent and aging at 17S ℃ for different time. The effects of hot extrusion, solution quench ing and aging treatment on the microstructure of Al-Cu-Mn alloy were studied. The results show that the large grains are not found and grain boundaries are not apparent after hot extrusion. Brittle hard phases are also crushed into small pieces and recrystallized grains appear around T phase. All these microstructure distributes along the direction of hot extrusion. After solution and quench treatment, second T phases arc finely distributed, and microstructurc after extrusion still exists; the number and size of un-dissolved brittle hard phases reduce, but the size of recrystallized grains increases. At the same time, some new tiny recrystallized grains are discovered. Aging treatment has little effect on the microstructure.
出处 《热加工工艺》 CSCD 北大核心 2013年第8期207-210,共4页 Hot Working Technology
关键词 Al-Cu-Mn 热挤压 固溶淬火 时效处理 微观组织 Al-Cu-Mn hot extrusion solution and quenching aging treatment microstructure
  • 相关文献

参考文献10

二级参考文献41

  • 1宁爱林,曾苏民.7A04铝合金快速热处理工艺研究[J].轻金属,2004(6):51-54. 被引量:7
  • 2周永江,熊艳才,洪润洲,姚惟斌.一种新型高强度铸造铝合金ZL210A[J].特种铸造及有色合金,2007,27(4):322-324. 被引量:6
  • 3陆文华.铸造合金及其熔炼[M].北京:机械工业出版社,1997.263.
  • 4高强.最新有色金属金相图谱大全[M].北京:冶金工业出版社,2005:975-979.
  • 5Takeda M, Yoshida. Discontinuity of GP[I] zone and θ double prime-phase in an Al-Cu alloy [J]. Scripta Materialia, 1999,41 (6): 643-649.
  • 6Gupta M,Qin S, Chin L W. Effect of particulate type on the microstructure and heat treatment response of Al-Cu-based metal-matrix composites [J]. Journal of Materials Processing Technology, 1997, 65:245-251.
  • 7Hwang J Y. The effects of Mn additions on the microstructure and mechanical properties of Al-Si-Cu casting alloys [J]. Materials Science and Engineering A, 2008, (488): 496-504.
  • 8Chia E H, McQueen H J. Microstructure Control in Alumium Alloy [A]. Deformation,Recovery and Recrystallization,TMS [C]. New York:TMS,1985. 179-220.
  • 9Okayasu M, Takasu S, Yoshie S. Microstrucmre and material properties of an Al-Cu alloy provided by the Ohno continuous casting technique [J]. Journal of Materials Processing Technology,2010,210(11): 1529-1535.
  • 10《铸造有色合金及其熔炼》联合编写组.铸造有色合金及其熔炼[M].北京:国防工业出版社,1985.71-75.

共引文献133

同被引文献43

引证文献7

二级引证文献39

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部