期刊文献+

时效工艺对2124铝合金板材的组织与性能影响 被引量:1

Effect of ageing process on microstructure and properties of 2124 aluminum alloy plate
下载PDF
导出
摘要 采用力学性能和透射电镜组织观察等方法,研究了2124铝合金板材时效工艺对性能和组织的影响。结果表明,2124铝合金板材的适宜峰值时效制度为185℃12 h,在此条件下,合金的抗拉强度Rm、屈服强度Rp0.2和伸长率A分别为483 N/mm2、454 N/mm2和7.4%;随着时效温度的提高和时间的延长,2124铝合金板材的强度先升高后降低,时效温度越高,强度上升越快,达到强度最大值的时间越短,但所达到的最大强度值越低。 The microstructure and properties of 2124 aluminum alloy thick plates with dif- ferent ageing process were investigated by mechanical property method and transmission elec- tron microscopy. The results show that the peak ageing process of 2124 aluminum alloy plates is 185~C for 12 h. Tensile strength Rm, yielding strength Rp0.2 and elongation A is 483 N/ 2 mm ,454 N/ram2 ,and 7.4% ,respectively. The strength of 2124 plate is raised to the maxi- mum and reduced gradually with temperature increasing and time prolonging. The higher the ageing temperature grows, the faster the strength climbs, the shorter time it takes to reach the maximum strength, and the lower the maximum strength becomes
出处 《轻合金加工技术》 CAS 北大核心 2014年第2期25-29,共5页 Light Alloy Fabrication Technology
关键词 2124铝合金 板材 组织 性能 时效处理 2124 aluminum alloy plate microstructure properties ageing treatment
  • 相关文献

参考文献8

  • 1王昌臻,潘清林,何运斌,邹亮,尹志民,聂波,何振波.2124铝合金热轧厚板的热处理制度[J].中南大学学报(自然科学版),2007,38(3):386-393. 被引量:27
  • 2RAMANATHAN S ,KARTHIKEYAN R,DEEPAK V. Hot deformation behavior of 2124 A1 alloy[ J]. Journal of material science and technology,2006,22 (5) : 611 , 615.
  • 3王昌臻,潘清林,何运斌,邹亮,尹志民,聂波,何振波.热处理对2124铝合金热轧厚板组织与性能的影响[J].矿冶工程,2007,27(1):68-71. 被引量:8
  • 4刘兵,彭超群,王日初,王小锋,李婷婷.大飞机用铝合金的研究现状及展望[J].中国有色金属学报,2010,20(9):1705-1715. 被引量:439
  • 5STALEY J T, LIU J, WARREN H. Aluminum alloys for aero structures [ J ]. Advanced Materials and Proces- ses,1997,152(4) : 1017 - 1021.
  • 6SMITH G W. Precipitation kinetics in solutionized aluminum alloy 2124 determination by scanning and isother- mal calorimetry [ J ]. Thermochimica Acta, 1998,317 ( 1 ) : 7 - 23.
  • 7WANG S C, STARINK M J, GAO N. Precipitation hardening in A1-Cu-Mg alloys revisited[ J ]. Scripta Materi- alaia,2006,54 (2) : 287 - 291.
  • 8HONYCOMBER W K. The plastic deformation of metals[ R]. Edwad Arnold Ltd, 1984: 18.

二级参考文献74

共引文献466

同被引文献6

引证文献1

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部