期刊文献+

Effect of Winglet Geometry Arrangement and Incidence on Tip Clearance Control in a Compressor Cascade

Effect of Winglet Geometry Arrangement and Incidence on Tip Clearance Control in a Compressor Cascade
原文传递
导出
摘要 An experimental study is conducted to investigate the influences of blade tip winglet on the flow field of a compressor cascade. The tests are performed in a low speed linear cascade with stationary endwall, with three blade tip configurations, including the baseline tip, the suction-side winglet tip and the pressure-side winglet tip. The fiowfield downstream of the cascade is measured using five-hole probe, from which the three-dimensional velocity field, vorticity field and pressure field are obtained. Static pressure measurements are made on the endwall above the blade row using pressure taps embedded in the plywood endwall. All measurements are made at both design and off-design conditions for tip clearance level of about 2 percent of the blade chord. The results revealed the incidence variation significantly affects the secondary flow and the associated loss field downstream of the cascade, where the tip leakage vortex and passage vortex exist as the major contributors on the field. The winglet geometry arrangements can change the trajectory of the tip leakage vortex. The suction-side winglet tip blade provides a lower overall total pressure loss coefficient when compared to the baseline tip blade and pressure-side winglet tip blade at all incidence angles.
出处 《Journal of Thermal Science》 SCIE EI CAS CSCD 2014年第4期381-390,共10页 热科学学报(英文版)
基金 supported by the National Natural Science Foundation of China(No.51076018) the Fundamental Research Funds for the Central Universities(No.3132014041) Specialized Research Fund for the Doctoral Program of Higher Education
关键词 blade tip winglet compressor cascade INCIDENCE tip clearance flow 叶尖泄漏涡 压气机叶栅 几何布置 发病率 间隙控制 翼梢小翼 压力损失系数 非设计条件
  • 相关文献

参考文献17

  • 1Koch, C. C. Stalling Pressure Rise Capability of Axial Flow Compressors. ASME Journal of Engineering for Gas Turbines and Power, 1981, 103,645-656.
  • 2Lakshminarayana, B. B. and Horlock J.H. Leakage and Secondary Flows in Compressor Cascades. Technical Report No.3483, The University of Liverpool, Liverpool, 1965.
  • 3Storer, J. A. and Cumpsty N. A. Tip Leakage Flow in Ax- ial Compressor. ASME Journal of Turbomachinery, 1991, 113, 252-259.
  • 4Kang, S. Investigation of the Three Dimensional Flowwithin a Compressor Cascade with and without Tip Clearance. PhD thesis, Vrije Universiteit Brussel, Brussel, 1993.
  • 5Williams, R., Smith, D. G., He Li, and Ingram, G. Ex- periments and Computations on Large Tip Clearance Ef- fects in a Linear Cascade. ASME Journal of Turbo- machinery, 2010, 132/021018.
  • 6Borello, D., and Rispoli F. Prediction of Tip-Leakage Flow in Axial Flow Compressor with Second Moment Closure. ASME Paper, GT2006-90535, Barcelona, Spain, 2006.
  • 7Gbadebo, S., Cumpsty, N.A., and Hynes, T.P. Interaction of Tip Clearance Flow and Three-Dimensional Separa- tions in Axial Compressors. ASME Journal of Turbo- machinery, 2007, 129, 679-685.
  • 8Tang, G., Simpson, R. L., and Tian Q. Experimental Study of Tip-Gap Turbulent Flow Structure. ASME Paper, GT2006-90359, Barcelona, Spain, 2006.
  • 9Booth, T. C., Dodge, P. R., and Hepworth H. K. Rotor-tip leakage: Part-basic Methodology. ASME Journal of Turbomachinery, 1982, 104, 154-159.
  • 10Harvey, N. W., and Ramsden, K. A Computation Study of a Noval Turbine Rotor Partial Shroud. ASME Paper, GT2000-668, Munich, Germany, 2000.

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部