FE Study for Reducing Forming Forces and Flat End Areas of Cylindrical Shapes Obtained by the Roll-Bending Process
FE Study for Reducing Forming Forces and Flat End Areas of Cylindrical Shapes Obtained by the Roll-Bending Process
摘要
A roll-bending process that minimizes the flat areas on the leading and trailing ends of formed plates will produce more accurate and easier assemble final shapes. There are several methods of minimizing flat areas, but they are costly or difficult to apply for thick plates. This study proposes a new, simple approach that reduces these flat areas. This approach includes moving the bottom roll slightly along the feeding direction and adjusting the bottom roll location. Sensitivity analyses were performed using a developed 3D dynamic FE （finite element） model of an asymmetrical roll-bending process in the Ansys/LS-Dyna software package. Simulations were validated by experiments run on an instrumented roll-bending machine. The FE results indicate that this new approach not only minimizes the flat areas but also reduces the forming forces.
参考文献25
-
1Available online at: http:// www.the fabricator.com/article/bending/roll-bending-a-wind-tower -with-a-three-roll-bender.
-
2J.T. Black, R.A. Kohser, Materials and Processes in Manufacturing, John Wiley & Sons, New York, 2008.
-
3S.L. Semiatin, ASM Handbook: Volume 14B-- Metalworking: Sheet Forming, ASM International, USA, 2006, pp. 386-393.
-
4O.D. Lascoe, Handbook of Fabrication Processes, ASM International, USA, 1989, pp. 48-52.
-
5M. Hua, K. Baines, I.M. Cole, Bending mechanisms, experimental techniques and preliminary tests for the continuous four-roll plate bending process, Journal of Material Processing Technology, 2nd Asia Pacific Conference on Materials Processing 48 (1-4) (1995) 159-172.
-
6M. Hua, K. Baines, I.M. Cole, Continuous four-roll plate bending: A production process for the manufacture of single seamed tubes of large and medium diameters, International Journal of Machine Tools and Manufacture 39 (6) (1999) 905-935.
-
7M. Hua, A formulation for determining the single-pass mechanics of the continuous four-roll thin plate bending process, Journal of Materials Processing Technology 67 (1-3) (1997) 189-194.
-
8M. Hua, Y.H. Lin, Effect of strain hardening on the continuous four-roll plate edge bending process, Journal of Materials Processing Technology 89-90 (1999) 12-18.
-
9M. Hua, D.H. Sansome, K. Baines, Mathematical modeling of the internal bending moment at the top roll contact in multi-pass four-roll thin-plate bending, Journal of Materials Processing Technology 52 (2-4) (1995) 425-459.
-
10M. Hua, Continuous four-roll plate bending process: Its bending mechanism and influential parameters, Journal of Materials Processing Technology 45 (1-4) (1994) 181-186.
-
1贾贺,荣伟,陈国良.基于LS-DYNA软件的降落伞充气过程仿真研究[J].航天器环境工程,2010,27(3):367-373. 被引量：23
-
2徐辅仁.飞机蒙皮壁板三轴滚弯成型力及中心辊进给量的计算[J].航空学报,1991,12(7). 被引量：8
-
3Wu Hongming,Liu Xiaoqiang,Wang Yaping,Tang Rongxi(Faculty 703,Beijing University of Aeronautics and Astronautics,Beijing, China, 100083).STUDY OF THE SOLID MODELINGTECHNIQUES ADAPTIVE TOPRODUCT MODELING[J].Chinese Journal of Aeronautics,1995,8(1):17-21.
-
4岳峰丽,董浩存,刘劲松.多筋结构件弯曲过程回弹模拟[J].沈阳工业学院学报,2004,23(1):11-13.
-
5魏童.END-FIRE天线系统在山区机场的应用[J].空中交通管理,2007(3):16-18.
-
6戴华杰,胡振东,咸奎成,彭福军.火星探测器气囊缓冲系统着陆过程仿真[J].力学季刊,2010,31(4):555-561. 被引量：17
-
7闫明,吴早凤,李森,龚思楚.某型飞机水上迫降性能仿真分析[J].教练机,2016(3):28-32. 被引量：1
-
8白宝光,郭文博,张加.乳制品质量安全水平多因素敏感性分析[J].食品工业科技,2013,34(20):49-52. 被引量：5
-
9王晓江,zgür Tekaslan.0.5mm厚钢板在弯曲过程中回弹量的确定[J].模具制造,2008,8(3):22-26.
-
10李忠,魏童.END-FIRE下滑天线系统在九寨黄龙机场的应用分析[J].民航科技,2007(1):6-8.
