期刊文献+

5CrNiMo模块锻件拔长折叠产生的判据 被引量:3

Folding Criterion of Die Block Forging of 5CrNiMo During Stretching
下载PDF
导出
摘要 为了研究不同压下量和送进量对拔长过程中锻件表面质量的影响,建立拔长折叠产生的判断条件,以5CrNiMo模块锻件为对象,用有限元软件DEFORM-3D建立了相对应的拔长模型,分析压下量和送进量比(M值)对最大折叠角和折叠深度的影响.结果表明,产生拔长折叠的M值临界区间为0.8-1.0.由此建立了拔长过程中锻件表面折叠产生的判据:M值低于0.8-1.0这一区间时,锻件表面不产生折叠;M值属于或超出该区间时,锻件表面产生折叠. In order to reveal the effects of reduction and feed amount on the surface quality of forgings during the stretching,and to establish a criterion judging the occurrence of stretching folding,a stretching model of 5CrNiMo die block forgings is constructed by means of the FEM software DEFORM-3D,and the effects of the reduction-tofeed amount ratio( namely the M value) on the maximum folding corner and the folding depth are discussed. It is found that the stretching folding occurs at a critical M interval of 0. 8 - 1. 0. On this basis,a criterion to judge the occurrence of folding during the stretching is established,that is,the folding of forging surfaces can be avoided when M is less than the range of 0. 8 -1. 0,while the folding occurs when M is within or exceeds the range of 0. 8 -1. 0.
出处 《华南理工大学学报(自然科学版)》 EI CAS CSCD 北大核心 2014年第11期14-18,24,共6页 Journal of South China University of Technology(Natural Science Edition)
基金 国家自然科学基金资助项目(51375172) 韶关市科技计划项目(2011CXY/C15)
关键词 5CrNiMo 模块锻件 拔长 折叠判据 DEFORM-3D 5Cr Ni Mo die block forging stretching folding criterion DEFORM-3D
  • 相关文献

参考文献15

  • 1程眉,张治民,于建民.三向主动加载塑性变形过程金属分流规律研究[J].锻压技术,2012,37(5):158-161. 被引量:4
  • 2刘国晖.大型锻件锻造的关键技术[J].中国机械工程,2004,15(22):2037-2040. 被引量:25
  • 3Chan W L,Fu M W,Lu J. FE simulation-based folding de- fect prediction and avoidance in forging of axially symme-trical flanged components [ J ]. Journal of Manufacturing Science and Engineering,2010,132 ( 5 ) : 1-6.
  • 4史宇麟,宋玉冰,薛秋云.大锻件两次镦拔锻造的工艺优化[J].热加工工艺,2007,36(5):51-53. 被引量:13
  • 5Sasaki Naohiko,Horii Tanetada,Fujiwara Mikio,et al. Strength- toughness balance of the Japanese sword and changes in car- bon content and as quenched hardness of HAGANE steel with cyclic folding forging [ J]. Journal of the Iron and Steel Institute of Japan,2000,86 ( 1 ) :45- 50.
  • 6Arentoft M, Wanheim T. The basis for a design support system to prevent defects in forging [ J ]. J Mater Process Technol, 1997,69( 1/2/3 ) :227-232.
  • 7黄珍媛,章弦,郭雷,阮锋.基于成形过程的闭塞式冷锻工艺优化[J].华南理工大学学报(自然科学版),2012,40(7):57-61. 被引量:4
  • 8中国机械工程学会塑性工程学会.锻压手册(1)[M].北京:机械工业出版社,2008.
  • 9Shahram Kheirandish,Ahmad Noorian.Effect of Niobium on Microstructure of Cast AISI H13 Hot Work Tool Steel[J].Journal of Iron and Steel Research International,2008,15(4):61-66. 被引量:29
  • 10Zhang Xiaoxun, Ma Chiying, Sun Yunhua, et al. Stress analysis and failure mechanism of H13 steel hot-forging die for automobile engine crankshaft [ J ]. Applied Me- chanics and Materials ,2012,217/218/219 : 1994-1997.

二级参考文献62

共引文献100

同被引文献24

引证文献3

二级引证文献6

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部