期刊文献+

线切割与真空热扩散焊组合工艺制备微模具 被引量:5

Laminated fabrication of micro-mold based on WEDM and thermal diffusion welding
下载PDF
导出
摘要 采用线切割和真空压力热扩散焊组合工艺制备了高深宽比的三维微结构。分别研究了线切割与热扩散焊工艺并获得了较好的工艺参数用于制备微模具。首先,在脉冲宽度为10μs,脉冲间隔为40μs,线切割电流为0.28A,电压为60V的条件下,对100μm厚的铜箔进行线切割,获得了多层二维微结构。然后,在热扩散温度为850℃,热扩散时间为10h,压力为1.0μPa的工艺参数作用下,对多层铜箔二维微结构进行真空压力热扩散焊接,通过多层二维微结构的叠加形成微模具,并制备了六棱台微型腔模具及微型级联齿轮模具。实验结果表明:三维微模具表面形貌较好,制作结果较理想,与设计模型基本相符。最后,通过超声模压成型分别获得了二阶和三阶的塑料级联齿轮。这些微塑件质量良好,验证了该工艺方法的可行性。 A 3D micro-structure with a high aspect ratio was fabricated by combining Wire Electrical Discharge Machining(WEDM)and vacuum pressure thermal diffusion welding.The WEDM and thermal diffusion welding were researched,and the better technological parameters were obtained to fabricate a micro-mold.Firstly,a copper foil with a thickness of 100μm was cut to obtain a multilayer 2D micro-structure under the conditions of apulse width of 10μs,apulse interval of 40μs,a wire cutting current of 0.28 Aand a voltage of 60 V.Then,the 2D micro-structure of a multilayer copper foil was fabricated by vacuum pressure thermal diffusion welding under the technologicalparameters in a thermal diffusion temperature of 850°C,a thermal diffusion time of 10 hand a pressure of 1.0μPa.The multilayer copper 2D microstructure was connected together by vacuum pressure thermal diffusion welding to fit into a six frustum pyramid mold and gear molds with twostage steps and three-stage steps,respectively.Experimental results indicate that the 3D micro-mold with good surface quality is an ideal fabrication and fits to design models.Finally,based on ultrasonic powder molding,two-stage and three-stage plastic gears are respectively obtained.These micro plastic parts show good quality,which verifies the feasibility and usability of laminated micro molds.
出处 《光学精密工程》 EI CAS CSCD 北大核心 2015年第4期988-995,共8页 Optics and Precision Engineering
基金 国家自然科学基金资助项目(No.51175348 No.51375315 No.51405306) 中国博士后科学基金资助项目(No.2014M552233) 深圳市科技研发资金基础研究项目(No.JCYJ20130329143934356 No.JCYJ20140418095735629)
关键词 三维微结构 微注塑模具 线切割 真空压力热扩散焊 3D micro-structure micro-injection mold Wire Electrical Discharge Mechining(WEDM) vacuum pressure thermal diffusion welding
  • 相关文献

参考文献19

  • 1BROUSSEAU B E, DIMOV S S, PHAM D T. Some recent advances in multi-material micro- and nano-manufacturing [J]. International Journal of Advanced Manufacturing Technology, 2010, 47 : 161-180.
  • 2于同敏,宫德海.微型模具制造技术研究与发展[J].中国机械工程,2005,16(2):179-183. 被引量:19
  • 3LEE D, HARUTAKA M, HIROSHI H. 3D UV- micro replication using cylindrical PDMS mold [J]. Microsyst. Technol. , 2010, 16:1399-1411.
  • 4WANG M W. Microceramic injection molding of a multilayer micropatterned micropart [J]. Intern- ational Journal of Advanced Manufacturing Technology, 2010,51: 145-153.
  • 5SHIU P P, KNOPF G K, OSTOJIC M. Fabri- cation of metallic micro-molds by laser and electro- discharge micromachining [ J ]. Microsyst. Technol. , 2010, 16:477-485.
  • 6YAN X X, LIU J Q, SHEN X C, et al: Hollow metallic microneedles fabricated by combining bulk silicon micromachining and UV-LIGA technology [J]. Microsyst. Technol. , 2012, 18:37-42.
  • 7杜立群,莫顺培,张余升,刘冲.UV-LIGA和微细电火花加工技术组合制作三维金属微结构[J].光学精密工程,2010,18(2):363-368. 被引量:13
  • 8马雅丽,刘文开,刘冲,杜立群.UV-LIGA技术在制作细胞培养器微注塑模具型腔中的应用[J].光学精密工程,2013,21(5):1228-1233. 被引量:6
  • 9PFEIFFERA M, ENGELA A, SCHOLZE S W S, et al: Microstructuring of steel and hard metal using femtosecond laser pulses [ J ]. Physics Procedia, 2011, 12:60-66.
  • 10张朝阳,李中洋,王耀民,毛卫平.激光冲击效应下的力学电化学微细刻蚀加工[J].光学精密工程,2012,20(6):1310-1315. 被引量:7

二级参考文献74

  • 1杜立群,朱神渺,喻立川.后烘温度对SU-8光刻胶热溶胀性及内应力的影响[J].光学精密工程,2008,16(3):500-504. 被引量:8
  • 2崔峰,靖向萌,赵小林,丁桂甫,张卫平,陈文元.SU-8胶模去除技术[J].微细加工技术,2007(1):1-6. 被引量:6
  • 3王晓东,刘冲,马骊群,罗怡,王立鼎.塑料微流控芯片的制作及其自动化[J].高技术通讯,2004,14(7):45-48. 被引量:9
  • 4任忠辉,宋博岩,韩荣第,刘明宇.电火花微能脉冲电源研究现状[J].电加工与模具,2006(3):29-32. 被引量:7
  • 5YU Z Y, MASUZAWA T, FUJINO M. Micro- EDM for three-dimensional cavities[J]. Annals of the CIRP, 1998,47(1):169-172.
  • 6TONG H,LI Y,WANG Y, et al.. Servo scanning 3D micro-EDM based on macro/micro-dual-feed spindle [J ]. International Journal of Machine Tools & Manufacture, 2008,48:858-869.
  • 7TAKAHATA K, SHIBAIKE N, GUCKEL H. High-aspect ratio WC-Co Microstructure Produced by the Combination of LIGA and Micro-EDM[J]. Microsystem Technologies, 2000,6 : 175-178.
  • 8EGASHIRA K, MIZUTANI K. EDM at Low Open-ciruit Voltage[J]. Journal of the Japan Society of Electrical Machining Engineers, 2003,37 (85) : 18-23.
  • 9TANAKA T,NOMURA T, FUNABIKI Y, et al.. Fabrication of a tapered structure by means of exposure to diffracted UV light[J]. MicroNano Mechatronics and Human Science, 2006, International Symposium on : 1-6.
  • 10YU Z Y,MASUZAWA T, FUJINO M. 3D micro- EDM with simply shaped eleetrode[J]. Annals of CIRP, 1997,46(1):1-8.

共引文献50

同被引文献39

引证文献5

二级引证文献9

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部