期刊文献+

低速轴流压气机转子叶片三维优化的数值研究 被引量:4

Numerical study on three-dimensional optimization of low-speed axial compressor rotor blade
原文传递
导出
摘要 为了深入认识低速大尺度轴流压气机端壁区的流动,减小流动损失,提高其气动性能,采用数值模拟和优化相结合的手段,针对用于低速模拟的某低速大尺度轴流压气机原型转子的三维积叠线进行了优化,提高了其设计工况下的气动性能.结果表明:优化转子轮毂附近无法承受过大的负荷;相比于原型转子,优化转子主要的性能提升位于轮毂附近,一定程度的正弯有效减小了轮毂区的流动损失,具有"前加载"的效果,抑制了叶根尾缘的流动分离,转子总压损失减小约19.4%. To deepen the knowledge of endwall flow in the large-scale low-speed axial compressor,reduce accordingly its flow loss and improve its aerodynamic performance,numerical simulation and optimization were presented.With numerical tool,three-dimensional stacking principle was optimized to improve the design operation point aerodynamic performance for the prototype rotor of a large-scale low-speed axial compressor in low speed simulation.Results show that,near-hub region of the optimized rotor cannot undertake large blade loading;compared with the prototype rotor,the main region of performance improvement of optimized rotor locates near the hub region,and a certain degree of positive bend in this region effectively helps to reduce its flow loss.It shows the effect of"loaded leading edge",which suppresses flow separation near the trailing edge;consequently nearly 19.4% of total pressure loss is reduced.
出处 《航空动力学报》 EI CAS CSCD 北大核心 2015年第2期483-490,共8页 Journal of Aerospace Power
基金 高等学校博士学科点专项科研基金(20123218120009)
关键词 压气机转子 流动损失 气动性能 数值优化 流动分离 compressor rotor flow loss aerodynamic performance numerical optimization flow separation
  • 相关文献

参考文献14

  • 1Wisler D C. Loss reduction in axial-flow compressor through low-speed model testing[J]. Journal of Engineer- ing for Gas Turbines and Power, 1985,107(2):354-363.
  • 2Lyes P A, Ginder R B. Low-speed compressor tests of swept and bowed blade designs[R]. International Symposi- um on Air Breathing Engines, ISABE 99-7048,1999.
  • 3Wisler D C. Core compressor exit stage study: Volume I blading design[R]. NASA Contractor Report CR-135391, 1977.
  • 4Wisler D C, Halstead D E, Beacher B F, Improving com- pressor and turbine performance through cost-effective low-speed testing [R]. International Symposium on Air Breathing Engines, ISABE 99-7073,1999.
  • 5Lyes P A, Ginder R B. Experimental evaluation of the high-to-low speed transformation process for a highly load- ed core compressor stage [R]. ASME Paper 98-GT-334, 1998.
  • 6Lyes P A. Low speed axial compressor design and evalua- tion, high speed representation and endwall flow control studies[D]. Cranfield.-Cranfield University,1999.
  • 7Gallimore S J,Bolger J J, Cumpsty N A, et al. The use of sweep and dihedral in multistage axial flow compressor bladingPart I university research and methods develop- ment[J]. Journal of Turbomachinery, 2002,124 (4): 521- 532.
  • 8Gallimore S J,Bolger J J, Cumpsty N A, et al. The use of sweep and dihedral in multistage axial flow compressor blading :Part l] low and high-speed designs and test verifi- cation[J]. Journal of Turbomachinery, 2002,124 (4) : 533- 541.
  • 9王志强,胡骏,王英锋,翟贤超.用于低速模拟试验的低速模型压气机气动设计[J].航空学报,2010,31(4):715-723. 被引量:14
  • 10王志强,胡骏,王英锋,阮立群.高压压气机低速模拟试验[J].航空学报,2012,33(5):828-838. 被引量:7

二级参考文献27

  • 1陈懋章.中国航空发动机高压压气机发展的几个问题[J].航空发动机,2006,32(2):5-11. 被引量:35
  • 2Simth L H Jr.多级轴流压气机中的机匣附面层[C]//.德中叶栅流的研究.北京:国防工业出版社,1978.
  • 3Wisler D C. Loss reduction in axial-flow compressors through low-speed model testing[J]. Journal of Engineering for Gas Turbines and Power, 1985, 107 (2): 354- 363.
  • 4Wisler D C, Halstead D E, Beacher B F. Improving compressor and turbine performance through cost-effective low speed testing[C]//14th International Symposium on Air Breathing Engines. 1999.
  • 5Lyes P A, Ginder R B. Experimental evaluation of the high to low speed transformation process for a highly loaded core compressor stage[C]//43rd International Gas Turbin & Aeroengine Congress & Exhibition. 1998.
  • 6Lyes P A, Ginder R B. Low speed compressor tests of swept and bowed blade designs[C]//14th International Symposium on Air Breathing Engines. 1999.
  • 7Gallimore S J, Bolger J J, Cumpsty N A, et al. The use of sweep and dihedral in multistage axial flow compressor blading--part Ⅰ : university research and methods devel opment[J]. Journal of Turbomachinery, 2002, 124(4) 521-532.
  • 8Gallimore S J, Bolger J J, Cumpsty N A, et al. The use of sweep and dihedral in multistage axial flow compressor blading part Ⅱ : low and high-speed designs and test veri fication[J]. Journal of Turbomachinery, 2002, 124 (4) : 533-541.
  • 9Wisler D C, Bauer R C, Okiishi T H. Secondary flow, turbulent diffusion and mixing in axial-flow compressors [J], Journal of Turbomachinery, 1987, 109(4): 455 -482.
  • 10Horlock J H. Flow trough a repeating stage in an axial compressor: a reconsideration[J]. Journal of Turbomachinery, 2004, 126(4): 677-679.

共引文献31

同被引文献59

引证文献4

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部