期刊文献+

孔隙率对多孔金属结合剂金刚石节块性能的影响 被引量:3

Influence of Porosity on the Performances of Porous Metal-bonded Diamond Blocks
下载PDF
导出
摘要 以碳酸氢铵为造孔剂,采用真空热压烧结法制备了多孔铜基结合剂金刚石节块。随着碳酸氢铵含量的增加,金刚石节块的孔隙率逐渐升高,抗弯强度逐渐降低,自锐性提高。用不同孔隙率的金刚石节块磨削硬质合金,观察了磨削后金刚石节块的表面状况,研究了孔隙率与磨削比的关系。结果表明:当孔隙率为20%左右时,金刚石节块的磨削比最高。 Ammonium bicarbonate was used as the pore forming agent and the porous Cu-matrix bond diamond blocks were prepared by the method of vacuum hot pressing sinte-ring.With the increasing content of ammonium bicarbonate,the porosity of diamond blocks increased,but flexural strength decreased and self sharpness improved.The blocks with different porosity were used to grinding cemented carbide,The surface condition of diamond blocks were observed after grinding and the relationship between the porosity and grinding ratio was studied.The results showed that when the porosity was about 20%,the grinding ratio attained the maximum.
作者 赵亚庆 何方
出处 《超硬材料工程》 CAS 2015年第5期18-23,共6页 Superhard Material Engineering
基金 郑州市科技攻关项目 单层金刚石钎焊研究(074SSG24110-1)
关键词 碳酸氢铵 多孔金刚石节块 孔隙率 自锐性 磨削比 Ammonium bicarbonate Porous diamond block Porosity Self sharpness Grinding ratio
  • 相关文献

参考文献10

  • 1刘树.金属结合剂金刚石砂轮的研究[J].科技视界,2012(35):72-72. 被引量:4
  • 2张文学.超高速磨削技术在机械制造领域中的应用研究[J].企业技术开发(下旬刊),2014,33(2):40-40. 被引量:3
  • 3H. Deng,G. Y. Chen,C. Zhou, et al. Processing parameter optimization for the laser dressing of bronze-bonded diamond wheels[J]. Applied Surface Science, 2014, 290: 475-481.
  • 4J. B. Mao,F. L. Zhang,G. C. Liao, etal. Effect of granulated sugar as pore former on the microstructure and mechanical properties of the vitrified bond cubic boron nitride grinding wheels[J]. Materials ~ Design, 2014, 60:328 333.
  • 5侯永改,路继红,张明岩,田久根.成孔剂对陶瓷结合剂CBN磨具结构与性能影响的研究[J].金刚石与磨料磨具工程,2014,34(1):48-52. 被引量:8
  • 6刘明耀,熊华军,夏举学.陶瓷空心球对金属结合剂金刚石砂轮性能的影响[J].金刚石与磨料磨具工程,2012,32(2):34-38. 被引量:7
  • 7Timothy D. Davis, Julia DiCorleto, David Sheldon, et al. A route to highly porous grinding wheels by selective extraction ofpore inducers with dense carbon dioxide[J]. The Journal of Su percritical Fluids, 2004, 30(3): 349-358.
  • 8H.ONISHI. Fabrication of New Porous Metal-Bonded Grind ing Wheels by HIP Method and Machining Electronic Ceramics [J]. Journal of Porous Materials, 1997, (4): 187-198.
  • 9S. H. TRUONG,Y. IS()NO,T. TANAKA. Scanning electron microscopic study and mechanical property examination of a bond bridge= development of a porous metal bonded diamond wheel[J]. Journal of Materials Processing Technology, 1999, 89~90(1999): 385-391.
  • 10W. F. Ding,J. H. Xu,Z. Z. Chen, et al. Fabrication and performance of porous metal bonded CBN grinding wheels u- sing alumina bubble particles as pore forming agents[J].The International Journal of Advanced Manufacturing Technology. 2012, 67(5-8): 1309 1315.

二级参考文献17

共引文献16

同被引文献41

引证文献3

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部