期刊文献+

基于NURBS曲线的S型级数式速度规划算法 被引量:8

S-type series velocity planning algorithm based on NURBS curves
下载PDF
导出
摘要 针对NURBS曲线插补时采用连续积分的速度规划算法与插补离散不一致性的问题,提出一种NURBS曲线的S型级数式速度规划算法,该算法完全按离散方式进行设计,满足实际插补时在插补周期内匀速、速度阶跃变化的离散性要求。根据已知条件计算出加减速、匀速等相应段的插补周期数,以此规划出离散级数式速度曲线。S型级数式速度规划算法与实际插补离散性要求一致,且设定的加减速余量因子修正了圆整算法对速度造成的损失。通过MATLAB仿真实验验证了该算法的有效性。 For inconsistencies of discrete speed requirement with continuous velocity planning in NURBS curve interpolation,a S-type series velocity planning algorithm was proposed for NURBS curves,which was entirely designed by the discrete method to meet the discrete requirements of uniform speed within the interpolation cycle and its step changes between interpolation cycle in actual interpolations.According to the known conditions to calculate the number of interpolation cycle,Stype series velocity curve was planned for this reason.S-type series velocity planning algorithm was consistent with the actual interpolating speed requirements,and the speed margin factor compensated for speed losses caused by the rounding algorithm.MATLAB simulation results showed the effectiveness of the algorithm.
出处 《计算机集成制造系统》 EI CSCD 北大核心 2015年第12期3249-3255,共7页 Computer Integrated Manufacturing Systems
基金 国家自然科学基金资助项目(51375419 51575466 51575210) 湖南省自然科学基金青年资助项目(14JJ3076) 湖南省教育厅一般资助项目(14C1067)~~
关键词 级数式算法 速度规划 余量因子 NURBS曲线 数控系统 series algorithm velocity planning margin factor NURBS curves numencal control systems
  • 相关文献

参考文献14

  • 1PIEGL L, TILLER W. The NURBS book[M:. 2nd edtion. Berlin, Germany: Springer-Verlag, 1997.
  • 2WANG J B,YAU H T. Real-time NURBS interpolator: appli cation to short linear segments[J3. International Journal of Ad vanced Manufacture Technology,2009,41(11/12) :1169-1185.
  • 3吴继春,唐小琦,陈吉红,周会成.一种实时快速NURBS插补算法研究与实现[J].计算机集成制造系统,2011,17(6):1224-1227. 被引量:4
  • 4SUNG H N, MIN Y Y. A study on a generalized parametric interpolator with real-time jerk-limited aeceleration[J]. Com- puter-Aided Design, 2004,36 (1) : 27-36.
  • 5胡鸿豪,吴勇翀,肖绚.CNC系统直线加减速优化算法[J].机床与液压,2008,36(F05):287-288. 被引量:7
  • 6CHENG C W, TSAI M C. Real-time variable feed rate NUR- BS curve interpolator for CNC machining l-J]. International Journal of Machine Tools and Manufacture, 2004,23 ( 11 ) : 865- 873.
  • 7LIN M T,TSAI M S,YAU H T. Development of a dynamics- based NURBS Interpolator with Real-time Look-ahead algo- rithm:JJ. International Journal of Machine Tools : Manufac- ture. 2007,47(15) :2246-2262.
  • 8罗钧,汪俊,刘学明,张平,陈建端.基于S型加减速的自适应前瞻NURBS曲线插补算法[J].计算机集成制造系统,2013,19(1):55-60. 被引量:24
  • 9ERKORKMAZ K, ALTINTAS Y. Quintic spline interpotati-on with minimal feed fluctuation[J]. ASME Journal of Man- ufacturing Science and Engineering,2005,127(2):339-349.
  • 10ROU Chiwei,SHIN ChingIong, LEE Wenyou. Planning S-cur- ves in the coordinated PTP motion of multiple-ax is machines under velocity acceleration and jerk constraints[J]. Journal of the Chinese Institute of Electrical Engineering, 2003,10 (3) 221-234.

二级参考文献25

  • 1彭芳瑜,何莹,罗忠诚,李斌.NURBS曲线机床动力学特性自适应直接插补[J].华中科技大学学报(自然科学版),2005,33(7):80-83. 被引量:13
  • 2赵国勇,徐志祥,赵福令.高速高精度数控加工中NURBS曲线插补的研究[J].中国机械工程,2006,17(3):291-294. 被引量:47
  • 3杜道山,燕存良,李从心.一种实时前瞻的自适应NURBS插补算法[J].上海交通大学学报,2006,40(5):843-847. 被引量:20
  • 4陈友东,王田苗,魏洪兴,潘月斗.数控系统的直线和S形加减速研究[J].中国机械工程,2006,17(15):1600-1604. 被引量:55
  • 5YEH S S, HSU P L. The speed controlled interpolator for machining parametric curves[J]. Computer -Aided Design, 1999,31(5):349- 357.
  • 6XU R Z, XIE L, LI C X, et al. Adaptive parametric interpola tion scheme with limited acceleration and jerk values for NC machining[J]. Internationl Journal of Advnced Manufacture Technology,2008,36(3/4) :343 -354.
  • 7WANG J B, YAU H T. Real-time NURBS inlerpolator;appli cation to short linear segments[J]. InlernationlJournal of Ad- vnced Manufacture Technology, 2009,41 (11/12) ; 1169- 1185.
  • 8PIEGL L, TILLER W. The NURBS hooks[M]. Berlin, Ger- many: Springer-Verlag, 1997.
  • 9Cheng M Y,Tsai M C,Kuo J C.Real-time NURBS command generator for CNC servo controller[J].International Journal of Machine Tools & Manufacture,2002,(42):801-813
  • 10Choi B K,Yoo W S,Lee C S.Matrix representation for NURBS curve and surface[J].Computer-Aided Design,1990,22(4):235-240

共引文献50

同被引文献39

引证文献8

二级引证文献15

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部