期刊文献+

筛片参数优化对饲料粉碎机筛分效率的影响 被引量:19

Influence of screen parameters optimization on screening efficiency of feed hammer mill
下载PDF
导出
摘要 传统锤片式粉碎机普遍存在着筛分效率低于粉碎效率的问题,为了寻求提高粉碎机的筛分效率的途径,该文通过试验台试验与颗粒动力学仿真相结合的方法,通过研究粉碎机筛片的结构参数和分离装置内的气流速度对筛分效率之间的影响规律,揭示物料的透筛机理。通过试验台试验发现:随着气流速度的增大,筛分效率呈先高后低的趋势;筛孔形状和筛片安装角度对筛分效率的影响较大;筛孔的排列方式对筛分效率的影响较小。利用颗粒动力学仿真软件EDEM-FLUENT对颗粒筛分过程进行模拟仿真,模拟结果与试验结果基本吻合,二者的相对误差不超过4%,结果显示:气流速度为6~15 m/s时,物料透筛效率呈先逐渐增大后又逐渐降低的趋势;筛片安装角度在20~70°范围内,最佳筛片安装角度为35~45°;在筛片开孔率相同的情况下,长方孔的筛分效率最高,圆孔的筛分效率最低。研究认为:在多种组合中,气流速度为12.37 m/s,筛片安装角度为40°的长方形的T型筛孔的筛分效率最高。 Traditional hammer mill generally has the problem that the screening efficiency is lower than the grinding efficiency. In order to improve the screen efficiency of the hammer mill, based on the combination of experiment and numerical simulation method, the influence of the structure parameters of the hammer mill screen and the air flow velocity in the separation device on the screening efficiency was studied, the mechanism of screening was revealed, and the way to improve the screening efficiency of the crusher was explored. According to a type of hammer mill designed by research group, we designed a screening test bench to simulate the air flow field in the separation device of the hammer mill using a blower as the air flow source. In this experiment, 5 kinds of particle sizes through screen were selected, and the influences of 4 factors including the screen hole shape, the screen installation angle, the screen hole arrangement and the air flow velocity on the particle screening efficiency were investigated. In the experiment, 10 kinds of screens were adopted, which were composed of 5 kinds of screen hole shapes and 2 kinds of screen hole arrangements, and there were 11 screen installation angles and 8 kinds of air flow velocity levels selected. The 5 kinds of screen holes were the rectangular hole, the oblong hole, the hexagonal hole, the square hole and the circle hole. The 2 kinds of screen arrangements included “U” type and “T” type arrangement. The experiment showed that the screening efficiency was high and then became low after the air velocity increased; the screen hole shape and screen installation angle had lager effect on the screening efficiency; the arrangement of the screen holes had less effect on the screening efficiency. Also the EDEM-FLUENT software was used to simulate the process of particle screening; the simulation and the experiment results were basically consistent, and the relative error of the two was not more than 4%. Based on this, the research found the optimum combination of the structure parameters and the flow parameters of the screen: when the air flow rate was 6-15 m/s, the screen efficiency of the material was gradually increasing and then decreasing; when the air flow velocity was 6-7 m/s, the phenomenon of material passing through screen was not obvious, mainly because air was not sufficient to drive the movement of particles when the material was under the influence of gravity; when the air flow velocity was more than 7 m/s, the screen efficiency increased, and when air flow speed reached 12.37 m/s, the screening efficiency reached the optimal value, but when the air flow speed continued to increase, the screening efficiency decreased; when the air flow velocity reached 14.21 m/s, the air flow began to negatively impact the particles passing through the screen and the screening efficiency decreased. This was because when the energy of air flow was greater, the particle reached the screen panel with greater speed for the first time, and if they first failed to pass through the screen, they would hit the screen surface to rebound, thereby reducing the secondary screen penetration probability. When the screen installation angle was in the range of 20°-70°, the screening efficiency decreased with the screen installation angle, and the best screen installation angle was 35°-45°; if the screen’s opening rate was the same, the screening efficiency of the rectangular hole was the highest among the 5 kinds of screens, and the screening efficiency of circle hole was the lowest of all; the screen hole arrangement had little influence on the screening efficiency. Results suggest that when the air flow velocity was 12.37 m/s, and the screen installation angle was 40°, the rectangular “T” type arrangement had the highest screening efficiency of 0.72-0.74.
出处 《农业工程学报》 EI CAS CSCD 北大核心 2016年第22期284-288,共5页 Transactions of the Chinese Society of Agricultural Engineering
基金 国家自然科学基金资助项目(51105189) 内蒙古自然科学基金资助项目(2014MS0534) 内蒙古自治区高等学校科学研究项目(NJZC13153)
关键词 农业机械 加工 优化 锤片式粉碎机 筛孔形状 筛片安装角度 筛分效率 agricultural machinery processing optimization, hammer mill screen hole shape screen installation angle screening efficiency
  • 相关文献

参考文献10

二级参考文献105

共引文献257

同被引文献260

引证文献19

二级引证文献162

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部