期刊文献+

机械振动对消失模铸造铝合金组织与性能的影响 被引量:6

Effects of Mechanical Vibration on Microstructure and Mechanical Properties of Lost Foam Casting Aluminum Alloy
原文传递
导出
摘要 研究了机械振动对消失模铸造AlSi9Mg合金组织与性能的影响,并分析了其作用机理。结果表明,Z方向机械振动的AlSi9Mg合金的平均晶粒尺寸最小,布氏硬度、抗拉强度和伸长率最大,其次为XY方向,而X、XZ和XYZ方向振动的AlSi9Mg合金的平均晶粒尺寸稍大,布氏硬度、抗拉强度和伸长率相对较小。随着机械振幅或振动频率的增加,AlSi9Mg合金的平均晶粒尺寸呈现先减小而后增加的趋势,而布氏硬度、抗拉强度和伸长率都呈现为先增加而后降低的趋势。消失模铸造AlSi9Mg合金适宜的机械振动工艺:机械振动方向为Z向,机械振幅为0.10mm,机械振动频率为36 Hz,在此工艺下可以获得较好的强度与塑性。 Influences of mechanical vibration,amplitude and frequency on microstructure and mechanical properties of the AlSi9 Mg alloy were investigated,and the mechanism of its action was described.The results show that the average grain size of AlSi9 Mg alloy in Zdirection is the smallest,and hardness,tensile strength and elongation of the alloy reach maximum values,respectively,followed by XY,while average grain size of the AlSi9 Mg alloy in X,XZand XYZdirection is slightly increased,and Brinell hardness,tensile strength and elongation rate are relatively decreased.With the increase of the mechanical vibration amplitude and vibration frequency,average grain size of the AlSi9 Mg alloy is decreased firstly and then increased,while hardness,tensile strength and elongation of the alloy are increased firstly and then decreased.The suitable mechanical vibration parameters for AlSi9 Mg alloy in lost foam casting are presented as follows:mechanical vibration direction in Zdirection,mechanical amplitude of0.10 mm,mechanical vibration frequency of 36 Hz,and the desirable strength and plasticity can be obtained under the optimized parameters.
出处 《特种铸造及有色合金》 CAS CSCD 北大核心 2017年第2期166-169,共4页 Special Casting & Nonferrous Alloys
基金 国家自然科学基金资助项目(61473306)
关键词 机械振动 AlSi9Mg合金 组织 性能 Mechanical Vibration AlSi9Mg Alloy Microstructure Property
  • 相关文献

参考文献7

二级参考文献34

  • 1田学锋,樊自田,黄乃瑜.机械振动对消失模铸造镁合金组织及力学性能的影响[J].中国有色金属学报,2006,16(11):1838-1844. 被引量:32
  • 2谢礼志,吴树森,赵君文,毛有武.机械振动法制备铝合金半固态浆料的研究[J].铸造技术,2007,28(11):1482-1485. 被引量:7
  • 3Lin S P,Nie Z R,Huang H,et al.Thermodynamic calculation of Er-X and Al-Er-X compounds exist in Al-Mg-Mn-Zr-Er alloy[J].Trans.Nonferrous Met.Soc.China,2010,20:682-687.
  • 4Lee Y C,Dahle A K,Stjohn D H.Grain refinement of magnesium[C]//Magnesium Technology,Nashville Tennesseem,2000:211-218.
  • 5Barone M R,Caulk D A.A foam ablation model for lost foam casting of aluminum[J].International Journal of Heatand Mass Transfer,2005,48:4132-4149.
  • 6Caulk D A.A foam engulfment model for lost foam casting of aluminum[J].International Journal of Heatand Mass Transfer,2006,49:3831-3845.
  • 7Royset J, Ryum N. Scandium in aluminium alloys [J]. International Materials Reviews, 2005,50( 1): 19-44.
  • 8Lin S P, NieZR, HuangH. Annealing behavior ofmodified 5083 alloy[J]. MaterialsandDesign, 2010,31: 1607-1612.
  • 9Chirita G, Stefanescu 1, Soares D. Influence ofvibrationon the solidification behaviour and tensile properties of an AI-I 8wt% Si alloy[J]. MaterialsandDesign, 2009. 30:1575-1580.
  • 10Shuangping Lin,Zuoren Nie,Hui Huang,Bolong Li.Annealing behavior of a modified 5083 aluminum alloy[J].Materials and Design.2009(3)

共引文献35

同被引文献47

引证文献6

二级引证文献7

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部