期刊文献+

低频振动作用下45钢压缩力学行为分析 被引量:3

Mechanical behaviors of steel 45 during compression in the low-frequency vibration
原文传递
导出
摘要 利用低频振动拉/压试验机,将激振频率、激振力作为主要影响参数,对45钢进行了低频振动作用下的压缩试验,主要对试验钢的强度变化进行了研究。结果表明:试验钢在拉伸过程中,添加低频振动后,与超声振动作用类似,也表现出金属振动塑性成形的"体积效应",即平均应力减小,屈服强度和抗拉强度均降低;随激振力增大,试验钢在拉伸中的平均载荷减小;随激振频率减小,试验钢拉伸时的平均载荷呈外凸曲线变化,在185 Hz时平均载荷达到最大值。 By using the low frequency vibration drawing tester and taking the vibration frequency and vibration force as main parameters, compression experiments of steel 45 under low frequency vibration were carried out. The change of strength for the experimental steel was researched. Results show that when the vibration is added in the vibration drawing, the volume effect appears clearly in the metal vibration forming process as in the ultrasonic vibration, namely the mean stress decreases, yield strength and tensile strength increase; with the vi- bration force increases, the mean loads of the steel samples during drawing decrease ; with the vibration frequency going down, the mean loads change with outwards curve, and 185 Hz is the maximum mean load of drawing specimen.
出处 《塑性工程学报》 CAS CSCD 北大核心 2017年第3期166-170,共5页 Journal of Plasticity Engineering
基金 国家自然科学基金资助项目(50975131) 江西省自然科学基金资助项目(20132BAB206013)
关键词 低频振动 力学行为 屈服强度 体积效应 压缩试验 low-frequency vibration mechanical behavior yield strength volume effect compression experiment
  • 相关文献

参考文献6

二级参考文献51

  • 1张士宏.金属材料的超声塑性加工[J].金属成形工艺,1994,12(3):102-106. 被引量:29
  • 2李连诗,张力行,杨效平,钟轼.超声波振动拔管拔丝的研究[J].钢铁,1995,30(3):39-44. 被引量:13
  • 3蔡改贫,徐建波,翁海珊.扭转振动摆动辗压精密成形机理研究[J].锻压技术,2006,31(1):40-42. 被引量:7
  • 4郑金鑫,胡浩,程靳.超高频振动下材料本构关系探析[J].哈尔滨工业大学学报,1997,29(1):6-9. 被引量:19
  • 5艾厚庄.碳钢在振动拉伸时的性能研究[M].鞍山钢铁学院,1991..
  • 6Dawson G R,Winsper C E,Sansome D H.Applieation of High-and Low- Frequency Oscillations to the Plastic Deformation of Metals.Metal Forming, Part 1:1970.
  • 7H.O.K.Kirchner, W.K.Kromp, F.B.Prinz, P.Trimmel.Plastic Deformation under Simuhaneous Cyclic and Unidirectional Loading at Low and Ultrasonic Frequencies. Materials Science Engineering 1984-1985,68: 197-206.
  • 8Siegert K,Mock A.Wire drawing with ultrusonically oscillatign dies,Materials Processign Technology,1996,60:657-660.
  • 9Dawson G R,Winsper C E,Sansome D H,Application of high-and luw-frequency oseillatons to be plastic deformation of metals,Metal forming,1970,8:234-238:1970,9:254-261.
  • 10Gebbardt J,Funke P.Zidhen von Drabten mit uberlagerten Ulerasrhall-Schwingungen-Teil Ⅰ/Ⅱ.Drabt,1983,5(34):199-204L6(34):297-301.

共引文献36

同被引文献35

引证文献3

二级引证文献7

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部