期刊文献+

服务器CPU两相流微槽道冷却试验研究和节能分析

Experimental study and energy-saving analysis on cooling server's CPU with two-phase flow micro-channel
下载PDF
导出
摘要 设计一套采用R134a制冷剂的两相流微槽道冷却系统,用于冷却高发热密度服务器CPU。搭建测试平台,测试和对比该系统在不同CPU负荷和制冷剂过冷度下的散热性能。测试结果表明,通过饱和温度为25~30℃的R134a两相流相变传热,可将发热密度为3 W/cm2,总散热量在50~150 W的CPU表面温度控制在50~60℃。根据实测的制冷剂泵、冷却水泵功耗,在不同气候条件下(选取典型气候区的若干城市为代表),该系统应用于大型数据中心服务器散热的全年理论能效比在10以上,远高于常规机房空调。 One cooling system with two-phase flow micro-channel is proposed for high heat flux server's CPU,using R134 a as refrigerant.A test platform is set up,the test and comparison are conducted on the cooling performance of this system under different loads of CPU and supercooling degree of the refigerant.The test results show that through the phase-changing heat transfer of two-phase flow using R134 a with saturated temperature of 25-30 ℃,a stable temperature range of 50-60 ℃ can be obtained for the CPU surface with heat flux of 3 W/cm^2 and heat dissipated of 50-150 W.Based on the power consumption of tested refrigerant pump and cooling water pump,applying this system to cooling the server in large data centers at different climate areas(several typical cities chosen from each climate area)of China,the theoretical annual energy ratio can be over 10,which is much higher than that of common air-conditioning in computer room.
作者 田浩 庞晓风 Tian Hao;Pang Xiaofeng(Institute of Optics,Fine Mechanics and Physics,Chinese Academy of Sciences;)(Beijing NaYuanFeng Science and Technology Development Co.,Ltd.)
出处 《制冷与空调》 2018年第8期61-67,共7页 Refrigeration and Air-Conditioning
关键词 数据中心 CPU 两相流 微槽道 节能 data center CPU two-phase flow micro-channel energy-saving
  • 相关文献

参考文献7

二级参考文献86

  • 1黄翔.国内外蒸发冷却空调技术研究进展(1)[J].暖通空调,2007,37(2):24-30. 被引量:161
  • 2谢晓云,江亿,刘拴强,曲凯阳,于向阳.间接蒸发冷水机组设计开发及性能分析[J].暖通空调,2007,37(7):66-71. 被引量:44
  • 3Ravi Mahajan, Raj Nair, Vijay Wakharkar, et al. Emerging Directions for Packaging Technologies. Semiconductor Technology and Manufacturing, 2002, 6(2): 62-75.
  • 4B V Antohe, J L Lage, D C Price, et al. Numerical Characterization of Micro Heat Exchangers Using Experimentally Tested Porous Aluminum Layers. Int. J. Heat and Fluid Flow, 1996, 17(6): 594-603.
  • 5G Hetsroni, M Gurevich, R Rozenblit. Metal Foam Heat Sink for Transmission Window. Int. J. Heat and Mass Transfer, 2005 (48): 3793- 3803.
  • 6徐侃,刘明侯,刘东.多孔介质填充的小槽道散热器性能的研究,见;中国宇航学会第八届空间热物理会议论文集.南昌,2007.9:512-519.
  • 7H Y Zhang, K C Toh. Fluid Flow and Heat Transfer in Liquid Cooled Foam Heat Sinks for Electronic Packages. IEEE Transactions and Packaging Technologys, 2005, 28(2): 272-280.
  • 8Losey M W, Jackman J, Firebaugh S L, et al. Design and Fabrication of Microfluidic Devices for Multiphase Mixing and Reaction. J. Microelectromech, 2002, 11(6): 709-717.
  • 9Gaddis E S, Gnielski V. Pressure Drop in Horizontal Cross Flow Across Tube Bundles. Int. Chem. Eng., 1985, 25(1): 1 -15.
  • 10Sparrow E M, Grannis V B. Pressure Drop Characteristics of Heat Exchangers Consisting of Arrays of Diamond- Shaped Pin Fins. Int. J.Heat Mass Transfer, 1991, 34(3): 589-600.

共引文献161

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部