期刊文献+

异种铝合金激光诱导电弧拼焊接头塌陷研究 被引量:2

Joints Collapse of Dissimilar Aluminum Alloys During Laser-Induced Arc Welding
原文传递
导出
摘要 采用激光诱导TIG电弧焊方法进行了1.5 mm厚6061-T6和5083-O异种铝合金的拼焊试验,系统研究了激光的加入对焊接接头塌陷变化和力学性能的影响规律。结果表明:由于两种铝合金的化学成分和热物理性能的差异,焊接接头会出现不一致的塌陷现象;与电弧焊相比,激光的加入不仅可以有效降低焊接接头的塌陷程度,还会大幅降低焊接接头塌陷深度比的不一致程度;随着激光功率增大,焊接接头塌陷的不一致程度呈减小的趋势,导致接头受力情况发生变化,使接头强度呈先增后减的趋势。 Laser-induced TIG arc welding is used to weld 1.5-mm dissimilar aluminum alloys 6061-T6 and 5083-O to systematically study the influence of the addition of a laser on the collapse and mechanical properties of welded joints.We find that the welded joints appear inconsistent owing to the difference in chemical compositions and thermophysical properties of the two aluminum alloys used.Compared with traditional arc welding,the addition of a laser can not only effectively reduce the degree of collapse of the welded joint,but also greatly reduce the inconsistent collapse depth ratio of the welded joint.Moreover,the inconsistent collapse of the welded joints shows a decreasing trend with the increasing laser power used for welding.It causes the joint stress to change;therefore,the joint strength first increases and subsequently decreases.
作者 宋刚 符成学 于培妮 刘黎明 Song Gang;Fu Chengxue;Yu Peini;Liu Liming(School of Material Science and Engineering,Dalian University of Technology,Key Laboratory of Liaoning Advanced Welding and Joining Technology,Dalian,Liaoning 116024,China)
出处 《中国激光》 EI CAS CSCD 北大核心 2019年第10期139-146,共8页 Chinese Journal of Lasers
基金 国家自然科学基金(U1764251)
关键词 激光技术 激光诱导电弧焊 异种铝合金 薄板拼焊 不一致塌陷 laser technique laser-induced arc welding dissimilar aluminum alloys thin plate tailor welding inconsistent collapse
  • 相关文献

参考文献6

二级参考文献89

  • 1洪蕾,吴钢,陈武柱.保护气流对CO_2激光焊接铝合金的影响[J].中国激光,2005,32(11):1571-1576. 被引量:17
  • 2孙福娟,刘洪军,张丹峰.LY12CZ铝合金激光焊接工艺[J].中国激光,2006,33(2):273-277. 被引量:8
  • 3左敦桂,李芳,华学明,吴毅雄.铝合金焊接新技术在汽车制造中的应用[J].电焊机,2007,37(7):1-5. 被引量:30
  • 4Rich Hall. Profile of Kentucky's Aluminum Industry[R]. Office of Research and Information Technology Kentucky Cabinet for Economic Development, 2005.
  • 5A. Ribolla, G. L. Damoulis, G. F. Batalha. The use of Nd:YAG laser weld for large scale volume assembly of automotive body in white[J]. J. Mater. Process. Technol. , 2005, 164-165:1120-1127.
  • 6H. Zhan, D. R. White, T. DebRoy. Current issues and problems in laser welding of automotive aluminium alloys[J]. Int. Mater. Rev. , 1999, 44(6): 238-266.
  • 7PADMANABHAN R, BAPTISTA A J, OLIVEIRA M C, et al. Effect of anisotropy on the deep-drawing of mild steel and dual phase steel tailor-welded blanks [J]. Journal of Materials Pro cessing Technology, 2007, 184(1-3)- 288-293.
  • 8QIU X G, CHEN W L. The study on numerical simulation of the laser tailor welded blanks stamping [J].Journal of Materials Pro- cessing, 2007, 187-188 (12): 128-131.
  • 9CHOI Y, HEO Y, KIM H Y, et al. Investigations of weld-line movements for the deep drawing process of tailor welded blanks [J]. Journal of Materials Processing Technology, 2000, 108 (1) 1-7.
  • 10MEINDERS T, VAN DEN BERG A, HUETINK J. Deep draw- ing simulations of tailored blanks and experimental verification [J].Journal of Materials Processing Technology, 2000, 103 (1) : 65-73.

共引文献82

同被引文献37

引证文献2

二级引证文献5

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部