摘要
针对农用柔性底盘前轮转向时两偏置轴转向机构难以保持联动关系而影响顺利转弯的问题,基于阿克曼转向几何与交叉耦合控制原理,设计了偏置轴转向机构联动耦合控制策略,采用模糊PID控制算法对两转向轮转角联动轮廓误差进行补偿,并依据方向盘信号大小和变化率对电磁摩擦锁PWM控制信号占空比进行调节,以匹配偏置电动轮转向的角速度,使两转向机构形成耦合而保持期望联动关系;基于MATLAB/Simulink对控制策略进行了仿真,且在硬化路面上实施了阶跃转向、蛇行转向及随机转向3种运动方式的试验验证,并对比分析了转角分配控制下的前轮转向效果。试验结果表明:耦合控制方法下柔性底盘前轮阶跃转向响应均在0.8 s内,左、右侧转角最大超调为1.3°;电磁摩擦锁的开闭可较好匹配电动轮的转向;左、右前轮对于各自目标角具有良好的跟踪性能;3种转向方式下最大与平均跟随误差值均小于分配控制方法;两轮联动的最大与平均转角轮廓误差分别为:阶跃转向1.2°与0.6°、蛇行转向1.1°与0.6°、随机转向1.0°与0.5°;耦合控制下仿真与试验转角的轮廓误差变化趋势一致,最大误差为2.2°,证明仿真模型合理有效。耦合控制下偏置轴转向机构联动控制效果优于转角分配控制,转向效果良好,该文提出的柔性底盘偏置轴转向机构联动耦合控制策略有效且可行。
Agricultural flexible chassis(FC)is a kind of in-wheel motor driving electric vehicle applied for greenhouse.The FC is composed of 4 identical off-centered shaft mechanisms,which can be controlled independently.Through this kind of mechanism,the FC can achieve various motion types.However,it is difficult to maintain the linkage relationship between the 2 front off-centered shaft mechanisms when the FC is in front wheel steering motion,and hard to accomplish smoothly turning.In order to solve this problem,a coupling control strategy for linkage motion was proposed in this study.Firstly,the contour error of the 2 wheel steering angle was deduced based on the Ackermann steering geometry and the cross-coupling control principle.To reduce the contour error during steering,a fuzzy PID control algorithm was designed,which could realize parameters self-tuning.As the electromagnetic friction lock was controlled by pulse width modulation(PWM)signal,the duty cycle of the PWM signal had to be adjusted according to turning situation.Thus,a fuzzy logic method was then introduced to regulate the duty cycle.Namely,the PWM signal duty cycle can be in line with the steering wheel signal size and its change rate,and the motion of the electromagnetic friction lock can match the steering speed of the off-center shaft mechanism.In this way,the coupling control of the 2 front off-centered shaft mechanisms can be achieved.The control strategy was then verified through simulation based on MATLAB/Simulink.To further verify the effectiveness of the control strategy,the control program was loaded into the steering system hardware,and tests were carried out on hard surface road.According to the traditional vehicle steering test methods,step steering test,snake steering test and random steering test were conducted.The effects of front wheel steering under the steering angle allocation control method were compared with coupling control strategy.The simulation results demonstrated that the proposed control strategy was effective and feasible.The test results on hard surface road showed that the FC had a fast steering response in step steering test.The response time of step steering was 0.8s and overshoot was 1.3°under coupling control method during front wheel steering of the FC.The overshoot under allocation control was larger than coupling control and its fluctuation was notable.From the results of the snake steering and random steering,it was obviously that the steering angles of the left and the right front wheels had good tracking performance for their target angles,respectively.The opening and closing of electromagnetic friction lock can match the steering motion of the electric wheel well.The maximum and average following errors of 3 steering modes were less than those under the allocation control method.The maximum and average contour errors of the linkage motion were 1.2°and 0.6°for step steering,1.1°and 0.6°for snake steering,as well as 1.0°and 0.5°for random steering,respectively.All these errors were also smaller than the allocation control.Under the coupling control,the maximum steering error between simulation and test was 2.2°,and the contour error trend of them was consistent.The simulation model was reasonable and effective.The contour errors of the allocation control in these 3 kinds of tests had more fluctuations and larger range of fluctuations than coupling control.The steering performance under coupling control strategy was obviously better than the allocation control method.The steering angles of the 2 front wheels had maintained Ackerman steering geometry well.The coupling linkage control strategy proposed in this paper has good effectiveness and feasibility.This research can provide references for steering control or other applications of the FC.
作者
瞿济伟
郭康权
宋树杰
Tran Van Cuong
李翊宁
Qu Jiwei;Guo Kangquan;Song Shujie;Tran Van Cuong;Li Yining(College of Mechanical and Electronic Engineering,Northwest A&F University,Yangling 712100,China;Shaanxi Engineering Research Centre for Agriculture Equipment,Yangling 712100,China;College of Food Engineering and Nutritional Science,Shaanxi Normal University,Xi'an 710119,China;College of Electronic Engineering,Vietnam Russia Vocational Training College No 1,Phuc Yen City,15910,Vietnam)
出处
《农业工程学报》
EI
CAS
CSCD
北大核心
2019年第23期55-65,共11页
Transactions of the Chinese Society of Agricultural Engineering
基金
国家自然科学基金资助项目(51375401)
关键词
农业机械
控制
算法
柔性底盘
前轮转向
联动
耦合控制
试验
agricultural machinery
control
algorithm
flexible chassis
front wheel steering
linkage motion
coupling control
test