期刊文献+

气膜孔形状对高超声速飞行器对撞流气膜冷却效果的影响 被引量:1

Influence of the shape of the film hole on the film cooling under impinging stream for hypersonic vehicles
下载PDF
导出
摘要 文章通过仿真分析手段研究飞行高度50 km、飞行马赫数15的飞行条件下,不同孔型对对撞流的影响,得到不同孔型对气膜冷却效果的影响规律。采用计算流体动力学(CFD)方法,对在入口压力0.5 MPa、质量流量22.5 g/s的稳定短模态(SPM)工作模态下,气膜孔为圆柱直孔、收缩孔、连续扩张孔、分段扩张孔等工况开展对比研究,结果显示,扩张孔气膜冷却的壁面热流最大,圆柱孔的次之,收缩孔的最小。这表明,通过改变对撞流气膜孔的形状可以改变气流流动特性,进而产生不同的气膜冷却效果,在SPM工作模态下收缩孔的气膜冷却效果最好。 This paper studies the influence of different hole shapes on the film cooling to determine the dependency of the film cooling on the shape of the film hole in the impinging stream under the condition of 15 km in height and 15Ma in velocity.The CFD method is used to simulate four kinds of cooling holes,namely,the cylindrical hole,the shrinkage hole,the continuous expansion hole,and the piecewise expansion hole under the working state of the stable short penetration model(SPM),where the film cooling hole inlet conditions are set to be 0.5 MPa for the inlet pressure and 22.5 g/s for the mass flow.It is shown that the heat flux on the vehicle wall with the expansion hole is the maximum among the three cases;the value is smaller for the case of the cylindrical hole,and the lowest value is found for the shrinkage hole case.So that the shape of the hole can change the flow characteristics of impinging streams,manifested as different film cooling degrees.The best effect is seen for the shrinkage hole under SPM working mode.
作者 商圣飞 向树红 姜利祥 杨艳静 袁军娅 赵娅 SHANG Shengfei;XIANG Shuhong;JIANG Lixiang;YANG Yanjing;YUAN Junya;ZHAO Ya(Beijing Institute of Spacecraft Environment Engineering;National key Laboratory of Science and Technology on Reliability and Environmental Engineering:Beijing 100094,China;School of Astronautics,Beihang University,Beijing 100191,China)
出处 《航天器环境工程》 2020年第4期342-347,共6页 Spacecraft Environment Engineering
关键词 高超声速飞行器 气膜冷却 气膜孔形状 热流密度 计算流体动力学 hypersonic vehicle film cooling shape of film hole heat flux CFD
  • 相关文献

参考文献9

二级参考文献54

  • 1杨林华,李竑松.国外大型太阳模拟器研制技术概述[J].航天器环境工程,2009,26(2):162-167. 被引量:36
  • 2何琨,陈坚强,董维中.逆向喷流流场模态分析及减阻特性研究[J].力学学报,2006,38(4):438-445. 被引量:19
  • 3张正平,王宇宏,朱曦全.动力学综合环境试验技术现状和发展[J].装备环境工程,2006,3(4):7-11. 被引量:35
  • 4季艳.国外临近空间飞行器技术发展概述[J].国际航空,2006(9):84-85. 被引量:11
  • 5MARCUS Young, STEPHANIE Keith, ANTHONY Pancotti. An Overview of Advanced Concepts for Near-space Systems, AIAA-2009-4805[R]. 2009.
  • 6WILLIAM Everette Symolon. High-altitude, Long-enduran- ce UAVs vs. Satellites: Potential Benefits for US Army Applications, ADA523102[B]. (余不祥).
  • 7Goldstein R J, Eckert E R G. Effects of hole geometry and density on three-dimensional film cooling[J]. International Journal of Heat Mass Transfer, 1974, 17(2):595 -607.
  • 8Giovanna B, Giuseppe B, Giuseppe F. Fan-shaped hole effects on the aero-thermal performance of a film-cooled endwaii[J]. Journal of Turbomachinary, 2006, 128(1): 43-52.
  • 9Colban W, Gratton A, Thole K A. Heat transfer and film-cooling measurements on a stator vane with fan- shaped cooling holes[J]. Journal of Turbomachinary, 2006, 128(1): 53-61.
  • 10Michael G, Will C, Heinz S. Effect of hole geometry on the thermal performance of fan-shaped film cooling holes [J]. Journal of Turbomachinary, 2005, 127 (4): 718- 725.

共引文献115

同被引文献7

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部