期刊文献+

T6态ZM51变形镁合金的高周疲劳行为 被引量:4

High cycle fatigue behavior of T6-treated ZM51 alloy extrusion
下载PDF
导出
摘要 以工业化挤压生产大截面尺寸的ZM51镁合金为研究对象,测试挤压态和T6态合金沿挤压方向(ED)的静态力学性能,并在应力比R=-1的条件下,研究T6态ED试样的高周疲劳行为。结果表明:T6处理后,ED试样的拉伸和压缩强度均得到提升,但伸长率大幅降低,压缩屈服强度的提高幅度远低于拉伸屈服强度的,合金拉压屈服不对称性增加。T6态ZM51镁合金循环周次为1×107时的疲劳极限为103 MPa,约为其抗拉强度的30%。发生在裂纹尖端塑性区内的"拉伸孪生-退孪生"是主要的疲劳损伤机制。合金疲劳裂纹的萌生位置以试样表面附近的孪晶界为主,疲劳裂纹穿晶路径扩展。疲劳断口两侧存在覆盖整个断口的针状孪晶层,应力越大,孪晶层厚度越小,而单个晶粒内的针状孪晶的数量越多,且间距越小。 The industrially extruded ZM51 magnesium alloy was studied in the present work. The static mechanical properties of as-extruded and T6 treated samples along extrusion direction(ED) were tested, and the high cycle fatigue behavior of T6 ED samples were studied under stress ratio R=-1. The results show that the tensile and compressive strength of the ED sample are improved by T6 heat treatment, but the elongation is greatly reduced, and the increment of the compressive yield strength is much lower than that of the tensile yield strength, resulting in the rise in the yield-strength asymmetry. The fatigue strength of T6 treated ZM51 alloy is 103 MPa under 1×10~7 cycle conditions, which is about 30% of its tensile strength. The tensile twinning and detwinning mechanism play a dominate role in fatigue deformation process, which is occurred in the plastic zone of the crack tip. The fatigue crack mainly initiates at the twin boundaries near the specimen surface, and propagates in a trans-granular mode. There are a large number of needle twins on both sides of the fatigue fracture which cover the whole fracture. The larger the stress, the larger the number of needle twins, and the smaller the spacing. The thickness of twin layer near the fracture decreases with the increase of the stress.
作者 穆桐 石国梁 张奎 李兴刚 李永军 马鸣龙 袁家伟 MU Tong;SHI Guo-liang;ZHANG Kui;LI Xing-gang;LI Yong-jun;MA Ming-long;YUAN Jia-wei(State Key Laboratory of Nonferrous Metals and Processes,GRINM Group Co.,Ltd.,Beijing 100088,China;GRIMAT Engineering Institute Co.,Ltd.,Beijing 100088,China;General Research Institute for Non-ferrous Metals,Beijing 100088,China)
出处 《中国有色金属学报》 EI CAS CSCD 北大核心 2020年第8期1770-1780,共11页 The Chinese Journal of Nonferrous Metals
基金 江苏省成果转化项目(BA2017044) 高端装备用高性能镁合金变形加工产品研发及产业化。
关键词 变形镁合金 拉压屈服不对称性 高周疲劳 孪生 退孪生 wrought magnesium alloy tension-compression yield asymmetry high cycle fatigue twinning detwinning
  • 相关文献

参考文献11

二级参考文献254

  • 1徐锦锋,翟秋亚,袁森.AZ91D镁合金的快速凝固特征[J].中国有色金属学报,2004,14(6):939-944. 被引量:30
  • 2陈振华,夏伟军,程永奇,傅定发.镁合金织构与各向异性[J].中国有色金属学报,2005,15(1):1-11. 被引量:104
  • 3黄良余.铝硅合金变质机理的新发展和新观点(上)[J].特种铸造及有色合金,1995,15(4):30-32. 被引量:46
  • 4曹富荣,崔建忠,雷方,乐启炽.超轻镁合金的研究历史与发展现状[J].材料工程,1996,24(9):3-5. 被引量:27
  • 5GRAY J E, LUAN B. Protective coatings on magnesium and its alloys--A critical review[J]. Journal of Alloys and Compounds, 2002, 336(1/2): 88-113.
  • 6VIEHWEGER B, RICHTER G, DURING M, KARABET A, SVIRIDOV A, HARTMANN H, RICHTER U. Hydromechanisches tiefziehen und hochdruckblech-umformung als verfahren zur herstellung komplexer bauteile aus magnesium- feinblechen des typs AZ31B-0[J]. Material Wissenschaft und Werkstofftechnik, 2004, 35(7): 440-446.
  • 7HORSTEMEYER M F, YANG N, GALL K, MCDOWELL D L FAN J, MGULLETT P. High cycle fatigue of a die cast AZ91E-T4 magnesium alloy[J]. Acta Materialia, 2004, 52(5): 1327-1336.
  • 8YANG Y, LIU Y B. High cycle fatigue characterization of two die-cast magnesium alloys[J]. Materials Characterization, 2008, 59(5): 567-570.
  • 9WANG Q G, APELIAN D, GRIFFITH J R. Microstructural effects on the fatigue properties of aluminum castings[C]//Proc Materials Solutions 98, Rosemont, IL, USA, Materials Park, OH: ASM International, 1998: 217-222.
  • 10ELIEZER A, GUTMAN E M, ABRAMOV E, UNIGOVSKI Y.Corrosion fatigue of die-east and extruded magnesium alloys[J]. Journal of Light Metals, 2001, 1(3): 179-186.

共引文献669

同被引文献51

引证文献4

二级引证文献19

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部