期刊文献+

亚毫米级氧化锆陶瓷微珠的制备与表征

Preparation and Characterization of Submillimeter Ceramic Microspheres for Zirconia
原文传递
导出
摘要 以丙烯酰胺体系为基础,以柠檬酸铵(AC)为分散剂,过硫酸铵(APS)为引发剂,以液体石蜡,催化剂四甲基乙二胺(TEMED)为外部介质体系,将钇稳定氧化锆(YSZ)通过凝胶注模成型工艺制备氧化锆陶瓷微珠。采用热分析仪、X-射线衍射仪、扫描电子显微镜、阿基米德排水法等测试手段分别对烧成过程的物理化学变化、物相组成、显微结构、烧成线收缩率和致密度等进行了表征。结果表明:氧化锆微珠生坯在260~600℃进行排胶,整个烧成过程质量减少约16.5%;在1525℃下,样品晶粒发育良好;同时,AM含量为1%~5%时,获得烧成线收缩率平均为22.4%、对应相对体积密度平均为97.5%、表面光滑、球形度好、颗粒尺寸集中于0.2~0.3mm的氧化锆陶瓷微珠,具有良好的性能。 Based on the acrylamide system,using ammonium citrate(AC)as the dispersant,ammonium persulfate(APS)as the initiator,liquid paraffin,catalyst tetramethylethylenediamine(TEMED)as the external medium system,yttrium-stabilized zirconium oxide(YSZ)as raw materials,zirconia ceramic microspheres were prepared by gelcasting.The physical and chemical reactions during sintering,phase,microstructure,sintering linear shrinkage and density of microspheres were characterized by DTA-TG,XRD,SEM,Archimedes method and so on,respectively.The results show that the binders of zirconia microspheres green body removed at 260~600℃,and the mass decreases by about 16.5%in the course of sintering;grains of the sample are well developed at 1525℃;meanwhile,the surface smooth,high sphericity zirconium ceramic microspheres of relative bulk density of 97.5%,linear shrinkage rate of 22.4%on average and the particle size of 0.2~0.3 mm are obtained with good performance.
作者 石纪军 邓一星 孙国梁 肖卓豪 李秀英 李飞龙 SHI JIjun;DENG Yixing;SUN Guoliang;XIAO Zhuohao;LI Xiuying;LI Feilong(National Engineering Research Center for Domestic&Building Ceramics,Jingdezhen Ceramic Institute,Jingdezhen 333001,China;School of Sciences,Xi'an University of Technology,Xi'an 710048,China)
出处 《中国陶瓷》 CAS CSCD 北大核心 2021年第1期24-29,共6页 China Ceramics
基金 江西省重点研发计划(20192BBEL50020,20192BBE50039) 江西省自然科学基金(20202BABL204020) 景德镇市科技计划(20192GYZD008-34)。
关键词 凝胶注模 氧化锆 亚毫米 陶瓷微珠 Gelcasting Zirconia Submillimeter Ceramic microsphere
  • 相关文献

参考文献7

二级参考文献58

  • 1李飞,翟长生,王俊,孙宝德.PEG对陶瓷凝胶注模成型坯体表面起皮的抑制作用研究[J].材料导报,2004,18(9):86-88. 被引量:7
  • 2马天,代建清,何锦涛,张立明,黄勇.表面水解和热氧化对氮化硅粉料表面特性及分散特性的影响[J].稀有金属材料与工程,2005,34(1):86-90. 被引量:10
  • 3JANNEY M A, OMATETE O O. Method for molding ceramic powder using a water-based geleastlng: US, 50217,362. 1991.
  • 4YOUNG A C~ OMATETE O O, JANNEY M A, et at Gelcasting of alumina. J. Am. Ceram. Soc., 1991, 74(3): 612-618.
  • 5JANNEY M A, OMATETE O O, WALLS C A, et at Development of low-toxicity gelcasting systems. Journal of the American Ceramic Society, 1998, 81(3): 581-591.
  • 6XIE Z P, CHEN Y L, HUANG Y. A novel casting forming for ceramics by gelatine and enzyme catalysis. Journal of the European Ceramic Society, 2000, 20(3): 253-257.
  • 7MILLAN A J, MORENO R, NIETO M I. Thermogelling polysaccharides for aqueous gelcasting-Part I: A comparativestudy of gelling additives. J. Euro. Ceram. Soc., 2002, 22: 2209-2215.
  • 8BENGISU M, YILMAZ E. Gelcasting of alumina and zirconia using chitosan gels. Ceramics International, 2002, 28:431--438.
  • 9MONTGOMERY J K, DRZAL P L, SHULL K R, et al. Thermoreversible gelcasting: A novel ceramic processing technique. J. Am. Ceram. Sot., 2002, 85(5): 1164-1168.
  • 10XIE Z P, YANG J L, HUANG Y, et al. Gelation forming of ceramic compacts using agarose. British Ceramic Transactions, 1999, 98(2): 58-61.

共引文献55

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部