期刊文献+

浮法工艺玻璃带成形过程的模拟分析 被引量:2

Simulations on Glass Ribbon Forming Behavior in Float Process
原文传递
导出
摘要 建立了浮法工艺玻璃成形过程的玻璃带三维(3D)与Thin-Film模型,采用Ansys Polyflow软件对600 t/d锡槽内玻璃带成形过程进行了模拟研究,与3D模拟结果对比表明,Thin-Film模型可准确、高效地模拟玻璃带成形过程。根据玻璃带成形过程模拟结果,讨论了锡槽不同区域内玻璃带的成形状态,进一步模拟分析了玻璃带纵向与横向温度分布条件对不同厚度玻璃成形过程的影响,得到了4mm与10 mm浮法玻璃成形过程的较优成形温度条件。 A three dimensional(3 D)model and a thin-film model were proposed for the glass ribbon forming process in float process.The forming process of glass ribbon in a 600 t/d tin bath was simulated via a software named Ansys Polyflow.Compared to the 3 D model,the thin-film model is demonstrated to be more accurate and effective for the simulation of glass ribbon forming process.According to the simulation results,the forming process of glass ribbon in each zone of the tin bath was discussed.The influences of longitudinal and transverse temperature distributions on the forming process were analyzed for glass ribbons with different thicknesses.Finally,the optimized forming temperature condition is obtained for glass ribbon with a thickness of 4 mm or 10 mm,respectively.
作者 陈淑勇 李从云 王照猛 马立云 左泽方 CHEN Shuyong;LI Congyun;WANG Zhaomeng;MA Liyun;ZUO Zefang(State Key Laboratory of Advanced Technology for Float Glass,Benghu 233000,Anhui,China;Silica-based Materials Laboratory of Anhui Province,Bengbu 233000,Anhui,China;CNBM Bengbu Design and Research Institute for Glass Industry Co.,Ltd.,Bengbu 233018,Anhui,China)
出处 《硅酸盐学报》 EI CAS CSCD 北大核心 2021年第2期340-346,共7页 Journal of The Chinese Ceramic Society
基金 安徽省科技重大专项计划项目(17030901004)资助。
关键词 浮法 玻璃 成形 数值模拟 float glass forming numerical simulation
  • 相关文献

参考文献1

二级参考文献8

  • 1SOULES T F, BUSBEY R F, PEKHSON S M, et al. Finiteelement calculation of stresses in glass parts undergoing viscous relaxation [J]. J Am Ceram Soc, 1987, 70(2):90-95.
  • 2WILLIAMS J H,OWEN D R J,CESAR De Sa J M A. Numerical modeling of glass forming process [J]. Eng Comput(Pineridge), 1986(3) :266-275.
  • 3SADEGH N, VACHTSEVANOS G J. Modeling the glass forming process [J]. Glass Technol, 1997, 38(6):216-218.
  • 4LOCHEGNIES D, MARION C, CARPENTIES E, et al. Finite element contributions to glass manufacturing control and optimization, part 1: creep forming of flat volumes [J]. Glass Technol, 1996, 37(4):128-132.
  • 5STOKES Y M. Numerical design tools for thermal replication of optical quality surfaces [J]. Comput Fluids, 2000, 29(4):401-414.
  • 6MAYER H J, STIEHL C, ROEDER E. Applying the finiteelement method to determines the die swell phenomenon during the extrusion of glass rods with non-circular cross-sections [J].J Mater Process Technol, 1997, 70(1 - 3) :145-150.
  • 7NARAYANASWAMY O S. A one-dimensional model of stretching float glass [J]. J Am Ceram Soc, 1977,60(1 - 2): 1-5.
  • 8NARAYANASWAMY O S. Computer simulation of float glass stretching[J]. J AmCeramSoc,1981, 64(11):666-670.

共引文献8

同被引文献11

引证文献2

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部