期刊文献+

铜表面脉冲电化学射流加工的定域性和粗糙度分析

The Localization and Roughness Analysis of Pulsed Jet Electrochemical Machining on Copper Surface
原文传递
导出
摘要 电化学射流加工(Jet-ECM)是一种用于表面微细结构加工的超精密加工方法。但是,Jet-ECM加工的定域性不足,表面质量不高,无法满足高精度表面加工的需求。采用合理的电解液和脉冲电源参数可以提高电化学加工的精度和表面质量,但单纯基于试错的方法获得合理参数的难度极大。根据电化学反应和双电层的基本原理,将Jet-ECM系统等效为RC电路,用于指导脉冲Jet-ECM加工参数的选择。研究结果显示,磷酸基电解液Jet-ECM中采用脉冲电源能有效减少过切,提高铜表面加工的定域性,当加工电压为6.5 V时,采用10 kHz,50%占空比的脉冲电源相比直流电源定域性提高36%。降低加工电压和占空比也可有效提高加工定域性。但表面质量和定域性的变化趋势相反,降低加工电压和占空比不利于工件表面黏膜层的形成,降低了表面质量。本研究有助于进一步明确Jet-ECM加工中的电化学去除机理,提高无应力加工方法的加工精度,为Jet-ECM在工业中的进一步应用提供了指导。 Jet electrochemical machining(Jet-ECM) is a ultra-precision machining method that is widely used in microstructure processing. However, the localization and surface roughness of Jet-ECM may not meet the needs of the high-precision machining process. Appropriate electrolyte and pulse power parameters can improve the localization and surface roughness of Jet-ECM processing. However, it is very difficult to obtain the appropriate parameters based on trial and error. According to the mechanism of electrochemical reactions and electric double-layer(EDL), the Jet-ECM system is equivalent to the RC circuit which can be used to guide the selection of processing parameters. The results show that pulsed Jet-ECM has a higher localization than Jet-ECM with direct current(DC) power. When the pulse power parameters are 6.5 V, 10 kHz, 50% duty ratio, the localization increased 36% compared with the DC power. Reducing the voltage and duty ratio can effectively improve the machining localization. The surface quality is opposite to the localization, reducing the voltage and duty ratio are not conducive to the formation of the viscous film on the workpiece surface. The lack of the viscous film causes the surface roughness deterioration. This study helps to understand the mechanism in Jet-ECM of Cu, and guides the further use of Jet-ECM in industry.
作者 王可 周平 闫英 张超 郭东明 WANG Ke;ZHOU Ping;YAN Ying;ZHANG Chao;GUO Dongming(Key Laboratory for Precision and Non-traditional Machining Technology of Ministry of Education,Dalian University of Technology,Dalian 116024)
出处 《机械工程学报》 EI CAS CSCD 北大核心 2022年第7期258-266,共9页 Journal of Mechanical Engineering
基金 国家自然科学基金重大(51991373) 中央高校基本科研业务费专项资金(DUT20LAB108,DUT20ZD216)资助项目。
关键词 电化学射流加工 脉冲电源 双电层 定域性 表面质量 jet electrochemical machining pulse power electric double-layer localization surface roughness
  • 相关文献

参考文献5

二级参考文献49

  • 1纪延俊,何俊华,陈良益.气泡的散射光与气泡尺寸分布[J].激光技术,2004,28(4):414-416. 被引量:13
  • 2史先传,朱荻,徐惠宇.电解加工的间隙监测与控制[J].机械科学与技术,2005,24(5):536-539. 被引量:13
  • 3SEN M H,SHAN H S.A review of electrochemical maoro-to micro-hole drining processes[J].International Journal of Machine Tools and Manufacture,2005,45:137-152.
  • 4RAJURKAR K P,ZHU D,MCGEOUGH J A,et al.New developments in electrochemical machining[J].Annals of CIRP,1999,48(2):567-580.
  • 5WANG W,ZHU D,QU N S,et al.Electrochemical machining with vacuum extraction of electrolyte[J].Journal of Material Processing Technology,2010,210(2):238-244.
  • 6CHRYSSOLOURIS G,WALLLOWWITZ M.Electrochemical hole making[J].Annals of CIRP,1984,33:99-103.
  • 7SHARMAS,JAIN V K,SHEKHAR R.Electrochemical drilling of inconel supperalloy with acidified sodium chloride electrolyte[J].International Journal of Advanced Manufacturing Technology,2002,19:492-500.
  • 8KOZAK J,RAJURKAR K P,GULBINOWICZ D,et al.Investigations of micro electrochemical machining using ultrashort pulses[C] //UNIV Nebraska-Lincoln,15th International Symposium on Eleclro machining,Apr.23-27,2007,Pittsburgh,PA.Lincoln:UNIV NebraskaLincoln,Industrial&Management Systems Engineering,2007:319-324.
  • 9HEWIDY M S,EBEID S J,RAJURKAR K P,et al.Electrochemical machining under orbital motion conditions[J].Journal of Materials Processing Technology,2001,109(3):339-346.
  • 10袁哲俊, 王先逵. 精密和超精密加工技术. 北京:机械工业出版社, 1999

共引文献86

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部