在Gleeble-3500热模拟机上采用双道次热压缩试验,研究50Cr5MoV轧辊钢高温变形道次间隔时间内的静态软化行为,通过应力补偿法计算静态再结晶体积分数,分析热变形温度、应变速率、变形程度以及初始奥氏体晶粒尺寸对静态再结晶体积分数的影...在Gleeble-3500热模拟机上采用双道次热压缩试验,研究50Cr5MoV轧辊钢高温变形道次间隔时间内的静态软化行为,通过应力补偿法计算静态再结晶体积分数,分析热变形温度、应变速率、变形程度以及初始奥氏体晶粒尺寸对静态再结晶体积分数的影响,并建立50Cr5MoV轧辊钢的静态再结晶动力学模型,获得静态再结晶激活能191.85 k J/mol。结果表明:变形温度、应变速率、变形程度和道次间隔时间对静态再结晶体积分数影响较大,而初始奥氏体晶粒尺寸对静态再结晶体积分数影响很小;将静态再结晶动力学模型的预测值与实测值进行比较,二者吻合较好。展开更多
The hot deformation behaviors of Cr5 steel were investigated.The hot compression tests were conducted in the temperature range of 900-1150 °C under strain rates of 0.01,0.1 and 1 s^(-1).The constitutive equation ...The hot deformation behaviors of Cr5 steel were investigated.The hot compression tests were conducted in the temperature range of 900-1150 °C under strain rates of 0.01,0.1 and 1 s^(-1).The constitutive equation and material constants(Q,n,α ln A) are obtained according to the hyperbolic sine function and Zener-Hollomon parameter.Besides,dynamic recrystallization(DRX) grain size model and critical strain model are acquired.The processing maps with the strain of 0.1,0.3 and 0.5 are obtained on the basis of dynamic materials model.It has been observed that DRX occurs at high temperature and low strain rate.According to the processing map,the safety region exists in the temperature range of 920-1150 °C with strain rate of 0.01-0.20 s^(-1).展开更多
The dynamic recrystallization behavior of high strength steel during hot deformation was investigated.The hot compression test was conducted in the temperature range of 950-1150 °C under strain rates of 0.1,1 and...The dynamic recrystallization behavior of high strength steel during hot deformation was investigated.The hot compression test was conducted in the temperature range of 950-1150 °C under strain rates of 0.1,1 and 5 s-1.It is observed that dynamic recrystallization(DRX) is the main flow softening mechanism and the flow stress increases with decreasing temperature and increasing strain rate.The relationship between material constants(Q,n,α and ln A) and strain is identified by the sixth order polynomial fit.The constitutive model is developed to predict the flow stress of the material incorporating the strain softening effect and verified.Moreover,the critical characteristics of DRX are extracted from the stress-strain curves under different deformation conditions by linear regression.The dynamic recrystallization volume fraction decreases with increasing strain rate at a constant temperature or decreasing deformation temperature under a constant strain rate.The kinetics of DRX increases with increasing deformation temperature or strain rate.展开更多
Based on hot metal pretreatment （HMPT）-basic oxygen furnace （BOF）-Rheinstahl Heraeus （RH）-compact strip production （CSP） process, parameters controlling on cold rolling deep drawing substrate SPHE were investi...Based on hot metal pretreatment （HMPT）-basic oxygen furnace （BOF）-Rheinstahl Heraeus （RH）-compact strip production （CSP） process, parameters controlling on cold rolling deep drawing substrate SPHE were investigated during smelting and rolling process by composition design and technology control. The influence of parameters on chemical compositions, mechanical properties and microstructure was revealed by scanning electron microscope （SEM）. The results show that, 1） main chemical components in SPHE are w（C）_〈40×10^-6, w（Si）_〈 0.01%, w（S）_〈0.009%, w（N）〈20×10^-6, w（O）〈_ 25×10^-6; 2） main mechanical properties of the SPHE are Crs=274 MPa, 00=334 MPa, A=48.9%; 3） main performances of deep drawing quality （DDQ） grade steel produced by SPHE are as follows, transversely crs=167 MPa, 00=298 MPa, n=0.219, r=2.46; vertically σs=166 MPa, 00=298 MPa, n=0.226, r=2.39; in 45° direction σ=171 MPa, 00=308 MPa, n=0.214, t=2.26; 4） microstrueture of DDQ is ferrite, average grain size is Grade 7.5, and inclusion size is 3-10μm.展开更多
文摘在Gleeble-3500热模拟机上采用双道次热压缩试验,研究50Cr5MoV轧辊钢高温变形道次间隔时间内的静态软化行为,通过应力补偿法计算静态再结晶体积分数,分析热变形温度、应变速率、变形程度以及初始奥氏体晶粒尺寸对静态再结晶体积分数的影响,并建立50Cr5MoV轧辊钢的静态再结晶动力学模型,获得静态再结晶激活能191.85 k J/mol。结果表明:变形温度、应变速率、变形程度和道次间隔时间对静态再结晶体积分数影响较大,而初始奥氏体晶粒尺寸对静态再结晶体积分数影响很小;将静态再结晶动力学模型的预测值与实测值进行比较,二者吻合较好。
基金Project(51322405)supported by the National Natural Science Foundation of China
文摘The hot deformation behaviors of Cr5 steel were investigated.The hot compression tests were conducted in the temperature range of 900-1150 °C under strain rates of 0.01,0.1 and 1 s^(-1).The constitutive equation and material constants(Q,n,α ln A) are obtained according to the hyperbolic sine function and Zener-Hollomon parameter.Besides,dynamic recrystallization(DRX) grain size model and critical strain model are acquired.The processing maps with the strain of 0.1,0.3 and 0.5 are obtained on the basis of dynamic materials model.It has been observed that DRX occurs at high temperature and low strain rate.According to the processing map,the safety region exists in the temperature range of 920-1150 °C with strain rate of 0.01-0.20 s^(-1).
基金Project (51322405) supported by the National Natural Science Foundation of ChinaProject (CX2013B085) supported by Hunan Provincial Innovation Foundation for Postgraduate,China
文摘The dynamic recrystallization behavior of high strength steel during hot deformation was investigated.The hot compression test was conducted in the temperature range of 950-1150 °C under strain rates of 0.1,1 and 5 s-1.It is observed that dynamic recrystallization(DRX) is the main flow softening mechanism and the flow stress increases with decreasing temperature and increasing strain rate.The relationship between material constants(Q,n,α and ln A) and strain is identified by the sixth order polynomial fit.The constitutive model is developed to predict the flow stress of the material incorporating the strain softening effect and verified.Moreover,the critical characteristics of DRX are extracted from the stress-strain curves under different deformation conditions by linear regression.The dynamic recrystallization volume fraction decreases with increasing strain rate at a constant temperature or decreasing deformation temperature under a constant strain rate.The kinetics of DRX increases with increasing deformation temperature or strain rate.
基金Project(50971135) supported by the National Natural Science Foundation of China
文摘Based on hot metal pretreatment （HMPT）-basic oxygen furnace （BOF）-Rheinstahl Heraeus （RH）-compact strip production （CSP） process, parameters controlling on cold rolling deep drawing substrate SPHE were investigated during smelting and rolling process by composition design and technology control. The influence of parameters on chemical compositions, mechanical properties and microstructure was revealed by scanning electron microscope （SEM）. The results show that, 1） main chemical components in SPHE are w（C）_〈40×10^-6, w（Si）_〈 0.01%, w（S）_〈0.009%, w（N）〈20×10^-6, w（O）〈_ 25×10^-6; 2） main mechanical properties of the SPHE are Crs=274 MPa, 00=334 MPa, A=48.9%; 3） main performances of deep drawing quality （DDQ） grade steel produced by SPHE are as follows, transversely crs=167 MPa, 00=298 MPa, n=0.219, r=2.46; vertically σs=166 MPa, 00=298 MPa, n=0.226, r=2.39; in 45° direction σ=171 MPa, 00=308 MPa, n=0.214, t=2.26; 4） microstrueture of DDQ is ferrite, average grain size is Grade 7.5, and inclusion size is 3-10μm.
