Jet grouting is a method for improving of soil and its physical characteristics.However,in this method,grouting of cement slurry with high pressure and velocity may cause damaging to soil structure,and then excavated ...Jet grouting is a method for improving of soil and its physical characteristics.However,in this method,grouting of cement slurry with high pressure and velocity may cause damaging to soil structure,and then excavated grains of soil are removed from the borehole and replaced with cement slurry.The grains,which are remained around the borehole,mixed with slurry（cement） in-situ,can create an improved mass of soil.This mass is named＂Soilcrete＂.Soilcrete mass has special characteristics such as high strength,low deformability and very low permeability.In this paper,principles of jet grouting and effective parameters have been analyzed.Then the test results obtained from Soilcrete column have been investigated.Finally,the paper concludes with presenting amount of principle jet grouting parameters at foundation of Shahriar dam according to the results of jet grouting test.Based on the measurements,the diameter,Soilcrete UCS（uniaxial compression strength）,amount of the water,grout and air pressure and lifting and rotating speed in original site of jet grouting are 1.2～1.5 m,2～3 MPa,370～390 bar,10～15 bar,6～8 bar,7～8 cm/min and 7～8 cm/min,respectively.Also it can be seen that while the column diameter falls within the upper half of the range,some values of the compressive strength are close to the lower limit of the range.展开更多
Although pressure cells have been produced and installed successfully for decades,the accuracy of measured pressure is often inadequate.Due to large differences between the stiffness of pressure cells and the surround...Although pressure cells have been produced and installed successfully for decades,the accuracy of measured pressure is often inadequate.Due to large differences between the stiffness of pressure cells and the surrounding media,there is a considerable difference between applied pressure and that measured from pressure cells.It is often difficult and expensive to make a pressure cell with stiffness（modulus of elasticity） similar to the surrounding material in which it will be embedded.In order to improve this situation,a casing material with proportional dimensions is recommended as a means to obtain reliable results.In our study,the effect of using casing in the installation of pressure cells is investigated,providing the characteristics of casing.Some practical recommendations are presented to improve the accuracy of the results using casing.展开更多
文摘Jet grouting is a method for improving of soil and its physical characteristics.However,in this method,grouting of cement slurry with high pressure and velocity may cause damaging to soil structure,and then excavated grains of soil are removed from the borehole and replaced with cement slurry.The grains,which are remained around the borehole,mixed with slurry（cement） in-situ,can create an improved mass of soil.This mass is named＂Soilcrete＂.Soilcrete mass has special characteristics such as high strength,low deformability and very low permeability.In this paper,principles of jet grouting and effective parameters have been analyzed.Then the test results obtained from Soilcrete column have been investigated.Finally,the paper concludes with presenting amount of principle jet grouting parameters at foundation of Shahriar dam according to the results of jet grouting test.Based on the measurements,the diameter,Soilcrete UCS（uniaxial compression strength）,amount of the water,grout and air pressure and lifting and rotating speed in original site of jet grouting are 1.2～1.5 m,2～3 MPa,370～390 bar,10～15 bar,6～8 bar,7～8 cm/min and 7～8 cm/min,respectively.Also it can be seen that while the column diameter falls within the upper half of the range,some values of the compressive strength are close to the lower limit of the range.
文摘Although pressure cells have been produced and installed successfully for decades,the accuracy of measured pressure is often inadequate.Due to large differences between the stiffness of pressure cells and the surrounding media,there is a considerable difference between applied pressure and that measured from pressure cells.It is often difficult and expensive to make a pressure cell with stiffness（modulus of elasticity） similar to the surrounding material in which it will be embedded.In order to improve this situation,a casing material with proportional dimensions is recommended as a means to obtain reliable results.In our study,the effect of using casing in the installation of pressure cells is investigated,providing the characteristics of casing.Some practical recommendations are presented to improve the accuracy of the results using casing.
