In areas where hot mix asphalt(HMA)is likely to be exposed by any form of mineral oil the layer has to withstand the attack of these substances in order not to damage the construction.The European Standard EN 12697-43...In areas where hot mix asphalt(HMA)is likely to be exposed by any form of mineral oil the layer has to withstand the attack of these substances in order not to damage the construction.The European Standard EN 12697-43 provides a test procedure to determine the resistance of HMA to fuel.The paper reviews this method thoroughly.A completely revised and simplified test device for the brush test was developed meeting the requirements of the standard and creating results with a high repeatability at the same time.The test conditions given by the standard such as the exposure to fuel,cleaning of the specimen after exposure or the contact pressure of the brush were varied to isolate those test conditions with a substantial influence on the result.The research revealed that in the standard some conditions with a rather small influence are set quite strictly while other conditions with a distinct influence on the result are not defined with the required accuracy to obtain comparable and repeatable results.The paper presents suggestions for the improvement of the test method and the standard itself in respect to the layout of the test device and the definition of important test conditions to enhance the outcome of the EN 12697-43.展开更多
Rutting or permanent deformation is one of the major distress modes of hot mix asphalt in the field. Triaxial cycle compression testing （TCCT） is a standardized and scientifically accepted test method to address thi...Rutting or permanent deformation is one of the major distress modes of hot mix asphalt in the field. Triaxial cycle compression testing （TCCT） is a standardized and scientifically accepted test method to address this distress mode in the lab and to characterize the resistance to permanent deformation. In most labs and according to EN 12697-25, standard TGCTs are carried out with cyclic axial loading and a constant confining pressure. In road pavements on the other hand, dynamic traffic loading due to passing wheels leads to cyclic confining pressure. In order to bring the TCCT closer to reality, the radial reaction and its phase lag to axial loading in standard TCCTs are analyzed and an enhanced TCCT with cyclic confining pressure is introduced. The cyclic confining pressure takes into account the viscoelastic material response by the radial phase lag to axial phase loading. In a subsequent test program, TCCTs with different confining pressure amplitudes were carried out on two hot mix asphalts. Results from standard and enhanced TCCTs were analyzed, compared and discussed. It is shown that the resistance to permanent deformation in- creases significantly when the viscoelastic material response is taken into account in the TCCT by introducing cyclic confining pressure.展开更多
文摘In areas where hot mix asphalt(HMA)is likely to be exposed by any form of mineral oil the layer has to withstand the attack of these substances in order not to damage the construction.The European Standard EN 12697-43 provides a test procedure to determine the resistance of HMA to fuel.The paper reviews this method thoroughly.A completely revised and simplified test device for the brush test was developed meeting the requirements of the standard and creating results with a high repeatability at the same time.The test conditions given by the standard such as the exposure to fuel,cleaning of the specimen after exposure or the contact pressure of the brush were varied to isolate those test conditions with a substantial influence on the result.The research revealed that in the standard some conditions with a rather small influence are set quite strictly while other conditions with a distinct influence on the result are not defined with the required accuracy to obtain comparable and repeatable results.The paper presents suggestions for the improvement of the test method and the standard itself in respect to the layout of the test device and the definition of important test conditions to enhance the outcome of the EN 12697-43.
文摘Rutting or permanent deformation is one of the major distress modes of hot mix asphalt in the field. Triaxial cycle compression testing （TCCT） is a standardized and scientifically accepted test method to address this distress mode in the lab and to characterize the resistance to permanent deformation. In most labs and according to EN 12697-25, standard TGCTs are carried out with cyclic axial loading and a constant confining pressure. In road pavements on the other hand, dynamic traffic loading due to passing wheels leads to cyclic confining pressure. In order to bring the TCCT closer to reality, the radial reaction and its phase lag to axial loading in standard TCCTs are analyzed and an enhanced TCCT with cyclic confining pressure is introduced. The cyclic confining pressure takes into account the viscoelastic material response by the radial phase lag to axial phase loading. In a subsequent test program, TCCTs with different confining pressure amplitudes were carried out on two hot mix asphalts. Results from standard and enhanced TCCTs were analyzed, compared and discussed. It is shown that the resistance to permanent deformation in- creases significantly when the viscoelastic material response is taken into account in the TCCT by introducing cyclic confining pressure.
