We used refill friction stir spot welding(RFSSW)to join 2-mm-thick AZ91D-H24 magnesium alloy sheets,and we investigated in detail the effect of tool plunge depth on the microstructure and fracture behavior of the join...We used refill friction stir spot welding(RFSSW)to join 2-mm-thick AZ91D-H24 magnesium alloy sheets,and we investigated in detail the effect of tool plunge depth on the microstructure and fracture behavior of the joints.A sound joint surface can be obtained using plunge depths of 2.0 and 2.5 mm.Plunge depth was found to significantly affect the height of the hook,with greater plunge depths corresponding to more severe upward bending of the hook,which compromised the tensile-shear properties of the joints.The hardness reached a minimum at the thermo-mechanically affected zone due to the precipitation phases of this zone as it dissolved into theα-matrix during the welding process.The fracture modes of RFSSW joints can be divided into three types:shear fracture,plug fracture,and shear–plug fracture.Of these,the joint with a shear–plug fracture exhibited the best tensile-shear load of 6400 N.展开更多
In this study, we used the stop-action technique to experimentally investigate the material flow and microstructural evolution of alclad 2A12-T4 aluminum alloy during refill friction stir spot welding.There are two ma...In this study, we used the stop-action technique to experimentally investigate the material flow and microstructural evolution of alclad 2A12-T4 aluminum alloy during refill friction stir spot welding.There are two material flow components, i.e., the inward-or outward-directed spiral flow on the horizontal plane and the upward-or downward-directed flow on the vertical plane.In the plunge stage, the flow of plasticized metal into the cavity is similar to that of a stack, whereby the upper layer is pushed upward by the lower layer.In the refill stage, this is process reversed.As such, there is no obvious vertical plasticized metal flow between adjacent layers.Welding leads to the coarsening of S(Al2CuMg) in the thermo-mechanically affected zone and the diminishing of S in the stir zone.Continuous dynamic recrystallization results in the formation of fine equiaxed grains in the stir zone, but this process becomes difficult in the thermo-mechanically affected zone due to the lower deformation rate and the pinning action of S precipitates on the dislocations and sub-grain boundaries, which leads to a high fraction of low-angle grain boundaries in this zone.展开更多
基金financially supported by the National Science and Technology Major Project of China(No.2017ZX04005001)the Key Research&Development Program of Shandong Province,China(No.2018GGX103053)。
文摘We used refill friction stir spot welding(RFSSW)to join 2-mm-thick AZ91D-H24 magnesium alloy sheets,and we investigated in detail the effect of tool plunge depth on the microstructure and fracture behavior of the joints.A sound joint surface can be obtained using plunge depths of 2.0 and 2.5 mm.Plunge depth was found to significantly affect the height of the hook,with greater plunge depths corresponding to more severe upward bending of the hook,which compromised the tensile-shear properties of the joints.The hardness reached a minimum at the thermo-mechanically affected zone due to the precipitation phases of this zone as it dissolved into theα-matrix during the welding process.The fracture modes of RFSSW joints can be divided into three types:shear fracture,plug fracture,and shear–plug fracture.Of these,the joint with a shear–plug fracture exhibited the best tensile-shear load of 6400 N.
基金financially supported by the National Science and Technology Major Project of China (No.2017ZX04005001)the Key Research & Development program of Shandong Province (2018GGX103053)。
文摘In this study, we used the stop-action technique to experimentally investigate the material flow and microstructural evolution of alclad 2A12-T4 aluminum alloy during refill friction stir spot welding.There are two material flow components, i.e., the inward-or outward-directed spiral flow on the horizontal plane and the upward-or downward-directed flow on the vertical plane.In the plunge stage, the flow of plasticized metal into the cavity is similar to that of a stack, whereby the upper layer is pushed upward by the lower layer.In the refill stage, this is process reversed.As such, there is no obvious vertical plasticized metal flow between adjacent layers.Welding leads to the coarsening of S(Al2CuMg) in the thermo-mechanically affected zone and the diminishing of S in the stir zone.Continuous dynamic recrystallization results in the formation of fine equiaxed grains in the stir zone, but this process becomes difficult in the thermo-mechanically affected zone due to the lower deformation rate and the pinning action of S precipitates on the dislocations and sub-grain boundaries, which leads to a high fraction of low-angle grain boundaries in this zone.
