Delayed neutron loss is an important parameter in the safety analysis of molten salt reactors. In this study,to obtain the effective delayed neutron fraction under flow condition, a delayed neutron precursor transport...Delayed neutron loss is an important parameter in the safety analysis of molten salt reactors. In this study,to obtain the effective delayed neutron fraction under flow condition, a delayed neutron precursor transport was implemented in the Monte Carlo code MCNP. The moltensalt reactor experiment(MSRE) model was used to analyze the reliability of this method. The obtained flow losses of reactivity for 235 U and 233 U fuels in the MSRE are223 pcm and 100.8 pcm, respectively, which are in good agreement with the experimental values(212 pcm and100.5 pcm, respectively). Then, six groups of effective delayed neutron fractions in a small molten salt reactor were calculated under different mass flow rates. The flow loss of reactivity at full power operation is approximately105.6 pcm, which is significantly lower than that of the MSRE due to the longer residence time inside the active core. The sensitivity of the reactivity loss to other factors,such as the residence time inside or outside the core and flow distribution, was evaluated as well. As a conclusion,the sensitivity of the reactivity loss to the residence time inside the core is greater than to other parameters.展开更多
In this study,a numerical flow model of the fission products(FPs)in the primary loop system of a molten salt reactor(MSR)was established and solved using Mathematica 7.0.The simulation results were compared with those...In this study,a numerical flow model of the fission products(FPs)in the primary loop system of a molten salt reactor(MSR)was established and solved using Mathematica 7.0.The simulation results were compared with those of the ORIGEN-S program in the static burnup mode,and the deviation was found to be less than 10%,which indicates that the results are in good agreement.Furthermore,the FPs distribution in the primary loop system under normal operating conditions of the 2 MW MSR was quantitatively analyzed.In addition,the distribution phenomenon of the FPs under different flow rate conditions was studied.At the end of life,the FPs activity in the core region(including active region,and upper and lower plenum regions)accounted for 77.3%,and that in the hot leg #1,main pump,hot leg #2,heat exchanger,and cold leg region accounted for 1.2%,16.15%,0.99%,2.5%,and 1.9%,respectively,of the total FPs in the primary loop under normal operating conditions.The proportion of FPs in the core decreased with the increase in flow rate in the range of 2.24-22,400 cm^3 s^-1.The established analytical method and conclusions of this study can provide an important basis for radiation safety design of the primary loop,radioactive source management design,thermal-hydraulic safety analysis,and radiochemical analysis of FPs of 2 MW MSRs.展开更多
The neutronic properties of molten salt reactors(MSRs)differ from those of traditional solid fuel reactors owing to their nuclear fuel particularity.Based on the Monte-Carlo N particle transport code,the effects of th...The neutronic properties of molten salt reactors(MSRs)differ from those of traditional solid fuel reactors owing to their nuclear fuel particularity.Based on the Monte-Carlo N particle transport code,the effects of the size and shape of the fuel salt channel on the neutron physics of an MSR cell are investigated systematically in this study.The results show that the infinite multiplication factor(k?)first increases and then decreases with the change in the graphite cell size under certain fuel volume fraction(FVF)conditions.For the same FVF and average chord length,when the average chord length is relatively small,the k?values for different fuel salt channel shapes agree well.When the average chord length is relatively large,the k?values for different fuel salt channel shapes differ significantly.In addition,some examples of practical applications of this study are presented,including cell selection for the core and thermal expansion displacement analysis of the cell.展开更多
Present designs for molten salt thermal reactors require complex online processing systems, which are technologically challenging, while an accelerator-driven subcritical molten salt system can operate without an onli...Present designs for molten salt thermal reactors require complex online processing systems, which are technologically challenging, while an accelerator-driven subcritical molten salt system can operate without an online processing system, simplifying the design. Previous designs of accelerator-driven subcritical systems usually required very high-power proton accelerators(>10MW).In this research, a proton accelerator is used to drive a thorium-based molten salt fast energy amplifier(TMSFEA)that improves the neutron efficiency of the system. The research results show that TMSFEA can achieve a longterm stable state for more than 30 years with a rated power of 300 MW and a stabilizing effective multiplication factor(k(eff)) without any online processing. In this study, a physical design of an integrated molten salt energy amplifier with an initial energy gain of 117 was accomplished. According to the burn-up calculation, a molten salt energy amplifier with the rated power of 300 MW(th) should be able to operate continuously for nearly 40 years using a 1 Ge V proton beam below 4 m A during the lifetime. By the end of the life cycle, the energy gain can still reach 76,and^(233) U contributes 70.9% of the total fission rate, which indicates the efficient utilization of the thorium fuel.展开更多
The production of radionuclides(90)^Sr and(131)^I in molten salt reactors is an attractive option to address the global shortage of radionuclides.This study evaluated the production characteristics of(90)^Sr and(131)^...The production of radionuclides(90)^Sr and(131)^I in molten salt reactors is an attractive option to address the global shortage of radionuclides.This study evaluated the production characteristics of(90)^Sr and(131)^I in a modular molten salt reactor,such as equilibrium time,yield,and cooling time of isotopic impurities.The fuel burn-up of a small modular molten salt reactor was analyzed by the Triton module of the scale program,and the variation in the fission yields of the two nuclides and their precursors with burn-up time.The yield of(131)^I and~(131)Te has been increasing during the lifetime.131 I has an equilibrium time of about 40 days,a saturation activity of about 40,300 TBq,and while~(131)Te takes 250 min to reach equilibrium,the equilibrium activity was about 38,000 TBq.The yields of90 Sr and~(90)Kr decreased gradually,the equilibrium time of90 Kr was short,and(90)^Sr could not reach equilibrium.Based on the experimental data of molten salt reactor experiment,the amount of nuclide migration to the tail gas and the corresponding cooling time of the isotope impurities under different extraction methods were estimated.Using the HF-H_2 bubbling method,3.49×10^(5)TBq of(131)^I can be extracted from molten salt every year,and after13 days of cooling,the impurity content meets the medical requirements.Using the electric field method,1296 TBq of(131)^I can be extracted from the off-gas system(its cooling time is 11 days)and 109 TBq of(90)^Sr.The yields per unit power for(131)^I and(90)^Sr is approximately 1350 TBq/MW and 530 TBq/MW,respectively,which shows that molten salt reactors have a high economic value.展开更多
Fast reactors based on thorium fuel have enhanced inherent safety. Fluoride salt performs well as a coolant in high-temperature nuclear systems. In this paper,we present a reference core for a large fluoride-salt-cool...Fast reactors based on thorium fuel have enhanced inherent safety. Fluoride salt performs well as a coolant in high-temperature nuclear systems. In this paper,we present a reference core for a large fluoride-salt-cooled solid-fuel fast reactor(LSFR) using thorium–uranium fuel cycle. Neutronics physics of the LSFR reference core is investigated with 2D and 3D in-core fuel management strategy. The design parameters analyzed include the fuel volume fraction, power density level and continuous removal of fission products with 3D fuel shuffling that obtains better equilibrium core performance than 2D shuffling. A self-sustained core is achieved for all cases,and the core of 60% fuel volume fraction at 50 MW/m^3 power density is of the best breeding performance(average breeding ratio 1.134). The LSFR core based on thorium fuel is advantageous in its high discharge burn-up of 20–30% fissions per initial heavy metal atom, small reactivity swing over the whole lifetime(to simplify the reactivity control system), the negative reactivity temperature coefficient(intrinsically safe for all cases) and accepted cladding peak radiation damage. The LSFR reactor is a good alternative option for the deployment of a self-sustained thorium-based nuclear system.展开更多
Small modular thorium-based graphite-moderated molten salt reactors (smTMSRs), which combine the advantages of small modular reactors and molten salt reactors, are regarded as a wise development path to speed deployme...Small modular thorium-based graphite-moderated molten salt reactors (smTMSRs), which combine the advantages of small modular reactors and molten salt reactors, are regarded as a wise development path to speed deployment time. In a smTMSR, low enriched uranium and thorium fuels are used in once-through mode, which makes a marked difference in their neutronic properties compared with the case when a conventional molten salt breeder reactor is used. This study investigated the temperature reactivity coefficient (TRC) in a smTMSR, which is mainly affected by the molten salt volume fraction (VF) and the heavy nuclei concentration in the fuel salt (HN). The fourfactor formula method and the reaction rate method were used to indicate the reasons for the TRC change, including the fuel density effect, the fuel Doppler effect, and the graphite thermal scattering effect. The results indicate that only the fuel density has a positive effect on the TRC in the undermoderated region. Thermal scattering from both salt and graphite has a significant negative influence on the TRC in the overmoderated region. The maximal effective multiplication factor, which shows the highest fuel utilization, is located at 10% VF and 12 mol% HN and is still located in the negative TRC region. In addition, on increasing the heavy nuclei amount from 2 mol% HN to 12 mol% HN (VF = 10%), the total TRC undergoes an obvious change from - 11 to - 3 pcm/K, which implies that the change in the HN caused by the fuel feed online should be small to avoid potential trouble in the reactivity control scheme.展开更多
The 10 MW_(th) solid-fueled thorium molten salt reactor(TMSR-SF1) is a FLi Be salt-cooled pebble bed reactor to be deployed in 5–10 years, designed by the TMSR group. Due to a large amount of beryllium in the core, t...The 10 MW_(th) solid-fueled thorium molten salt reactor(TMSR-SF1) is a FLi Be salt-cooled pebble bed reactor to be deployed in 5–10 years, designed by the TMSR group. Due to a large amount of beryllium in the core, the photoneutrons are produced via(γ , n) reactions.Some of them are generated a long time after the fission event and therefore are considered as delayed neutrons. In this paper, we redefine the effective delayed neutrons into two fractions: the delayed fission neutron fraction and the delayed photoneutron fraction. With some reasonable assumptions, the inner product method and the k-ratio method are adopted for studying the effective delayed photoneutron fraction. In the k-ratio method, the Monte Carlo code MCNP6 is used to evaluate the effective photoneutron fraction as the ratio between the multiplication factors with and without contribution of the delayed neutrons and photoneutrons. In the inner product method, with the Monte Carlo and deterministic codes together, we use the adjoint neutron flux as a weighting function for the neutrons and photoneutrons generated in the core. Results of the two methods agree well with each other, but the k-ratio method requires much more computing time for the same precision.展开更多
With global warming,the demand for diversified energy sources has increased significantly.Transportable microreactors are important potential supplements to the global power market and are a promising development dire...With global warming,the demand for diversified energy sources has increased significantly.Transportable microreactors are important potential supplements to the global power market and are a promising development direction.This paper describes a 5 MW integrated long-life S-CO_(2)cooled vehicular microreactor(VMR)design based on tristructural isotropic(TRISO)fuel particles that aims to provide electricity for industrial power facilities,remote mines,and remote mountainous areas that are not connected to central power grids.First,to facilitate transportation,flexible deployment,and simplified operation and maintenance requirements,the VMR core and auxiliary system were designed to be reasonably small and as simple as possible.Second,the TRISO fuel particles used in the proposed VMR offer excellent properties,such as high inherent security and nonproliferation,which are vital for reactors in remote areas.In addition,a long core lifetime was achieved using the compact core design and enhanced fuel loading capacity,which is challenging when using TRISO as fuel.Finally,to make the VMR economically competitive in terms of improved neutron performance and fuel efficiency compared to similar designs,large-size TRISO particles and tube-in-duct fuel assembly were utilized and different core configurations were schemed and simulated to obtain the design that best satisfied the proposed criteria.The lifetime and burnup in the final optimized VMR were satisfactory at 21 years and43.9 MWd/kgU,respectively,with an adequate shutdown margin and excellent safety parameters to ensure safe operation.展开更多
The advantages of once-through molten salt reactors include readily available fuel,low nuclear proliferation risk,and low technical difficulty.It is potentially the most easily commercialized fuel cycle mode for molte...The advantages of once-through molten salt reactors include readily available fuel,low nuclear proliferation risk,and low technical difficulty.It is potentially the most easily commercialized fuel cycle mode for molten salt reactors.However,there are some problems in the parameter selection of once-through molten salt reactors,and the relevant burnup optimization work requires further analysis.This study examined once-through graphitemoderated molten salt reactor using enriched uranium and thorium.The fuel volume fraction(VF),initial heavy nuclei concentration(HN_(0)),feeding uranium enrichment(E_(FU)),volume of the reactor core,and fuel type were changed to obtain the optimal conditions for burnup.We found an optimal region for VF and HN_(0) in each scheme,and the location and size of the optimal region changed with the degree of E_(FU),core volume,and fuel type.The recommended core schemes provide a reference for the core design of a once-through molten salt reactor.展开更多
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of the Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘Delayed neutron loss is an important parameter in the safety analysis of molten salt reactors. In this study,to obtain the effective delayed neutron fraction under flow condition, a delayed neutron precursor transport was implemented in the Monte Carlo code MCNP. The moltensalt reactor experiment(MSRE) model was used to analyze the reliability of this method. The obtained flow losses of reactivity for 235 U and 233 U fuels in the MSRE are223 pcm and 100.8 pcm, respectively, which are in good agreement with the experimental values(212 pcm and100.5 pcm, respectively). Then, six groups of effective delayed neutron fractions in a small molten salt reactor were calculated under different mass flow rates. The flow loss of reactivity at full power operation is approximately105.6 pcm, which is significantly lower than that of the MSRE due to the longer residence time inside the active core. The sensitivity of the reactivity loss to other factors,such as the residence time inside or outside the core and flow distribution, was evaluated as well. As a conclusion,the sensitivity of the reactivity loss to the residence time inside the core is greater than to other parameters.
基金supported by the Chinese Academy of Sciences TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)The Frontier Science Key Program of Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘In this study,a numerical flow model of the fission products(FPs)in the primary loop system of a molten salt reactor(MSR)was established and solved using Mathematica 7.0.The simulation results were compared with those of the ORIGEN-S program in the static burnup mode,and the deviation was found to be less than 10%,which indicates that the results are in good agreement.Furthermore,the FPs distribution in the primary loop system under normal operating conditions of the 2 MW MSR was quantitatively analyzed.In addition,the distribution phenomenon of the FPs under different flow rate conditions was studied.At the end of life,the FPs activity in the core region(including active region,and upper and lower plenum regions)accounted for 77.3%,and that in the hot leg #1,main pump,hot leg #2,heat exchanger,and cold leg region accounted for 1.2%,16.15%,0.99%,2.5%,and 1.9%,respectively,of the total FPs in the primary loop under normal operating conditions.The proportion of FPs in the core decreased with the increase in flow rate in the range of 2.24-22,400 cm^3 s^-1.The established analytical method and conclusions of this study can provide an important basis for radiation safety design of the primary loop,radioactive source management design,thermal-hydraulic safety analysis,and radiochemical analysis of FPs of 2 MW MSRs.
基金This work was supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of Chinese Academy of Sciences(No.QYZDYSSW-JSC016)the Shanghai Sailing Program(No.Y931021031).
文摘The neutronic properties of molten salt reactors(MSRs)differ from those of traditional solid fuel reactors owing to their nuclear fuel particularity.Based on the Monte-Carlo N particle transport code,the effects of the size and shape of the fuel salt channel on the neutron physics of an MSR cell are investigated systematically in this study.The results show that the infinite multiplication factor(k?)first increases and then decreases with the change in the graphite cell size under certain fuel volume fraction(FVF)conditions.For the same FVF and average chord length,when the average chord length is relatively small,the k?values for different fuel salt channel shapes agree well.When the average chord length is relatively large,the k?values for different fuel salt channel shapes differ significantly.In addition,some examples of practical applications of this study are presented,including cell selection for the core and thermal expansion displacement analysis of the cell.
基金This work was supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of the Chinese Academy of Sciences(No.QYZDY-SSW-JSC016).
文摘Present designs for molten salt thermal reactors require complex online processing systems, which are technologically challenging, while an accelerator-driven subcritical molten salt system can operate without an online processing system, simplifying the design. Previous designs of accelerator-driven subcritical systems usually required very high-power proton accelerators(>10MW).In this research, a proton accelerator is used to drive a thorium-based molten salt fast energy amplifier(TMSFEA)that improves the neutron efficiency of the system. The research results show that TMSFEA can achieve a longterm stable state for more than 30 years with a rated power of 300 MW and a stabilizing effective multiplication factor(k(eff)) without any online processing. In this study, a physical design of an integrated molten salt energy amplifier with an initial energy gain of 117 was accomplished. According to the burn-up calculation, a molten salt energy amplifier with the rated power of 300 MW(th) should be able to operate continuously for nearly 40 years using a 1 Ge V proton beam below 4 m A during the lifetime. By the end of the life cycle, the energy gain can still reach 76,and^(233) U contributes 70.9% of the total fission rate, which indicates the efficient utilization of the thorium fuel.
基金supported by the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDA02010000)Thorium Uranium Fuel Cycle Characteristics and Key Problem Research Project(No.QYZDY-SSW-JSC016)Shanghai Natural Science Foundation(No.19ZR1468000)。
文摘The production of radionuclides(90)^Sr and(131)^I in molten salt reactors is an attractive option to address the global shortage of radionuclides.This study evaluated the production characteristics of(90)^Sr and(131)^I in a modular molten salt reactor,such as equilibrium time,yield,and cooling time of isotopic impurities.The fuel burn-up of a small modular molten salt reactor was analyzed by the Triton module of the scale program,and the variation in the fission yields of the two nuclides and their precursors with burn-up time.The yield of(131)^I and~(131)Te has been increasing during the lifetime.131 I has an equilibrium time of about 40 days,a saturation activity of about 40,300 TBq,and while~(131)Te takes 250 min to reach equilibrium,the equilibrium activity was about 38,000 TBq.The yields of90 Sr and~(90)Kr decreased gradually,the equilibrium time of90 Kr was short,and(90)^Sr could not reach equilibrium.Based on the experimental data of molten salt reactor experiment,the amount of nuclide migration to the tail gas and the corresponding cooling time of the isotope impurities under different extraction methods were estimated.Using the HF-H_2 bubbling method,3.49×10^(5)TBq of(131)^I can be extracted from molten salt every year,and after13 days of cooling,the impurity content meets the medical requirements.Using the electric field method,1296 TBq of(131)^I can be extracted from the off-gas system(its cooling time is 11 days)and 109 TBq of(90)^Sr.The yields per unit power for(131)^I and(90)^Sr is approximately 1350 TBq/MW and 530 TBq/MW,respectively,which shows that molten salt reactors have a high economic value.
基金supported by the ‘‘Strategic Priority Research Program’’ of the Chinese Academy of Sciences(No.XDA02010200)the Frontier Science Key Program of Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘Fast reactors based on thorium fuel have enhanced inherent safety. Fluoride salt performs well as a coolant in high-temperature nuclear systems. In this paper,we present a reference core for a large fluoride-salt-cooled solid-fuel fast reactor(LSFR) using thorium–uranium fuel cycle. Neutronics physics of the LSFR reference core is investigated with 2D and 3D in-core fuel management strategy. The design parameters analyzed include the fuel volume fraction, power density level and continuous removal of fission products with 3D fuel shuffling that obtains better equilibrium core performance than 2D shuffling. A self-sustained core is achieved for all cases,and the core of 60% fuel volume fraction at 50 MW/m^3 power density is of the best breeding performance(average breeding ratio 1.134). The LSFR core based on thorium fuel is advantageous in its high discharge burn-up of 20–30% fissions per initial heavy metal atom, small reactivity swing over the whole lifetime(to simplify the reactivity control system), the negative reactivity temperature coefficient(intrinsically safe for all cases) and accepted cladding peak radiation damage. The LSFR reactor is a good alternative option for the deployment of a self-sustained thorium-based nuclear system.
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘Small modular thorium-based graphite-moderated molten salt reactors (smTMSRs), which combine the advantages of small modular reactors and molten salt reactors, are regarded as a wise development path to speed deployment time. In a smTMSR, low enriched uranium and thorium fuels are used in once-through mode, which makes a marked difference in their neutronic properties compared with the case when a conventional molten salt breeder reactor is used. This study investigated the temperature reactivity coefficient (TRC) in a smTMSR, which is mainly affected by the molten salt volume fraction (VF) and the heavy nuclei concentration in the fuel salt (HN). The fourfactor formula method and the reaction rate method were used to indicate the reasons for the TRC change, including the fuel density effect, the fuel Doppler effect, and the graphite thermal scattering effect. The results indicate that only the fuel density has a positive effect on the TRC in the undermoderated region. Thermal scattering from both salt and graphite has a significant negative influence on the TRC in the overmoderated region. The maximal effective multiplication factor, which shows the highest fuel utilization, is located at 10% VF and 12 mol% HN and is still located in the negative TRC region. In addition, on increasing the heavy nuclei amount from 2 mol% HN to 12 mol% HN (VF = 10%), the total TRC undergoes an obvious change from - 11 to - 3 pcm/K, which implies that the change in the HN caused by the fuel feed online should be small to avoid potential trouble in the reactivity control scheme.
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)
文摘The 10 MW_(th) solid-fueled thorium molten salt reactor(TMSR-SF1) is a FLi Be salt-cooled pebble bed reactor to be deployed in 5–10 years, designed by the TMSR group. Due to a large amount of beryllium in the core, the photoneutrons are produced via(γ , n) reactions.Some of them are generated a long time after the fission event and therefore are considered as delayed neutrons. In this paper, we redefine the effective delayed neutrons into two fractions: the delayed fission neutron fraction and the delayed photoneutron fraction. With some reasonable assumptions, the inner product method and the k-ratio method are adopted for studying the effective delayed photoneutron fraction. In the k-ratio method, the Monte Carlo code MCNP6 is used to evaluate the effective photoneutron fraction as the ratio between the multiplication factors with and without contribution of the delayed neutrons and photoneutrons. In the inner product method, with the Monte Carlo and deterministic codes together, we use the adjoint neutron flux as a weighting function for the neutrons and photoneutrons generated in the core. Results of the two methods agree well with each other, but the k-ratio method requires much more computing time for the same precision.
基金supported by the National Natural Science Foundation of China(No.12005290)the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2020261)。
文摘With global warming,the demand for diversified energy sources has increased significantly.Transportable microreactors are important potential supplements to the global power market and are a promising development direction.This paper describes a 5 MW integrated long-life S-CO_(2)cooled vehicular microreactor(VMR)design based on tristructural isotropic(TRISO)fuel particles that aims to provide electricity for industrial power facilities,remote mines,and remote mountainous areas that are not connected to central power grids.First,to facilitate transportation,flexible deployment,and simplified operation and maintenance requirements,the VMR core and auxiliary system were designed to be reasonably small and as simple as possible.Second,the TRISO fuel particles used in the proposed VMR offer excellent properties,such as high inherent security and nonproliferation,which are vital for reactors in remote areas.In addition,a long core lifetime was achieved using the compact core design and enhanced fuel loading capacity,which is challenging when using TRISO as fuel.Finally,to make the VMR economically competitive in terms of improved neutron performance and fuel efficiency compared to similar designs,large-size TRISO particles and tube-in-duct fuel assembly were utilized and different core configurations were schemed and simulated to obtain the design that best satisfied the proposed criteria.The lifetime and burnup in the final optimized VMR were satisfactory at 21 years and43.9 MWd/kgU,respectively,with an adequate shutdown margin and excellent safety parameters to ensure safe operation.
基金supported by the Shanghai Sailing Program(No.19YF1457900)Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)+1 种基金National Natural Science Foundation of China(No.12005290)Youth Innovation Promotion Association of the Chinese Academy of Sciences(No.2020261)。
文摘The advantages of once-through molten salt reactors include readily available fuel,low nuclear proliferation risk,and low technical difficulty.It is potentially the most easily commercialized fuel cycle mode for molten salt reactors.However,there are some problems in the parameter selection of once-through molten salt reactors,and the relevant burnup optimization work requires further analysis.This study examined once-through graphitemoderated molten salt reactor using enriched uranium and thorium.The fuel volume fraction(VF),initial heavy nuclei concentration(HN_(0)),feeding uranium enrichment(E_(FU)),volume of the reactor core,and fuel type were changed to obtain the optimal conditions for burnup.We found an optimal region for VF and HN_(0) in each scheme,and the location and size of the optimal region changed with the degree of E_(FU),core volume,and fuel type.The recommended core schemes provide a reference for the core design of a once-through molten salt reactor.
