Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength,low density,and high modulus.In this study,the TA15-based...Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength,low density,and high modulus.In this study,the TA15-based composites reinforced with a volume fraction of 10% to 25%(TiB+TiC)were prepared using powder metallurgy and casting technique.Microstructural characterization and phase constitution were examined using optical microscopy(OM),scanning electron microscopy(SEM),and X-ray diffraction(XRD).In addition,the microhardness,room temperature(RT)and high temperature(HT)tensile properties of the composites were evaluated.Results revealed that the reinforcements are distributed uniformly even in the composites with a high volume of TiB and TiC.However,as the volume fraction exceeds 15%,TiB and TiC particles become coarsening and exhibit rod-like and dendritic-like morphology.Microhardness increases gradually from 321.2 HV for the base alloy to a maximum of 473.3 HV as the reinforcement increases to 25vol.%.Tensile test results indicate that a reinforcement volume fraction above 20% is beneficial for enhancing tensile strength and yield strength at high temperatures,but it has an adverse effect on room temperature elongation.Conversely,if the reinforcement volume fraction is below 20%,it can improve high-temperature elongation when the temperature exceeds 600℃.展开更多
The Mediterranean diet has long been recognized as one of the most effective ways to prevent and improve cardiovascular disease.Extra virgin olive oil(EVOO)is the typical sources of fat in the Mediterranean diet which...The Mediterranean diet has long been recognized as one of the most effective ways to prevent and improve cardiovascular disease.Extra virgin olive oil(EVOO)is the typical sources of fat in the Mediterranean diet which have been shown to have noteworthy nutritional value and positive impact on human health.It is worth noting that EVOO owes its superior nutritional value to its bioactive composition.The main component of EVOO is monounsaturated fatty acids(MUFAs)in the form of oleic acid.Oleic acid accounts for up to 70%-80%of EVOO.Secondly,EVOO contains approximately more than 30 phenolic compounds,of which HT is essential for the protection against cardiovascular diseases.In this review,we focused on the potential mechanisms of oleic acid and polyphenols combat cardiovascular diseases risk in terms of oxidative stress,inflammation,blood pressure,endothelial function and cholesterol.This review might provide a reference for the studies on cardiovascular protective effects of EVOO.展开更多
●AIM:To identify disease-causative mutations in families with congenital cataract.●METHODS:Two Chinese families with autosomaldominant congenital cataract(ADCC)were recruited and underwent comprehensive eye examinat...●AIM:To identify disease-causative mutations in families with congenital cataract.●METHODS:Two Chinese families with autosomaldominant congenital cataract(ADCC)were recruited and underwent comprehensive eye examinations.Gene panel next-generation sequencing of common pathogenic genes of congenital cataract was performed in the proband of each family.Sanger sequencing was used to valid the candidate gene mutations and sequence the other family members for co-segregation analysis.The effect of sequence changes on protein structure and function was predicted through bioinformatics analysis.Major intrinsic protein(MIP)-wildtype and MIP-G29R plasmids were constructed and microinjected into zebrafish single-cell stage embryos.Zebrafish embryonic lens phenotypes were screened using confocal microscopy.●RESULTS:A novel heterozygous mutation(c.85G>A;p.G29R)in the MIP gene was identified in the proband of one family.A known heterozygous mutation(c.97C>T;p.R33C;rs864309693)in MIP was found in the proband of another family.In-silico prediction indicated that the novel mutation might affect the MIP protein function.Zebrafish embryonic lens was uniformly transparent in both wild-type PCS2+MIP and mutant PCS2+MIP.●CONCLUSION:Two missense mutations in the MIP gene in Chinese cataract families are identified,and one of which is novel.These findings expand the genetic spectrum of MIP mutations associated with cataracts.The functional studies suggest that the novel MIP mutation might not be a gain-of-function but a loss-of-function mutation.展开更多
Due to the impact of source-load prediction power errors and uncertainties,the actual operation of the park will have a wide range of fluctuations compared with the expected state,resulting in its inability to achieve...Due to the impact of source-load prediction power errors and uncertainties,the actual operation of the park will have a wide range of fluctuations compared with the expected state,resulting in its inability to achieve the expected economy.This paper constructs an operating simulation model of the park power grid operation considering demand response and proposes a multi-time scale operating simulation method that combines day-ahead optimization and model predictive control(MPC).In the day-ahead stage,an operating simulation plan that comprehensively considers the user’s side comfort and operating costs is proposed with a long-term time scale of 15 min.In order to cope with power fluctuations of photovoltaic,wind turbine and conventional load,MPC is used to track and roll correct the day-ahead operating simulation plan in the intra-day stage to meet the actual operating operation status of the park.Finally,the validity and economy of the operating simulation strategy are verified through the analysis of arithmetic examples.展开更多
Background:Hai Honghua medicinal liquor(HHML),a famous hospital formula composed of 19 traditional Chinese medicines,has been successfully applied in treating soft tissue injury,fresh closed fracture,limb dysfunction ...Background:Hai Honghua medicinal liquor(HHML),a famous hospital formula composed of 19 traditional Chinese medicines,has been successfully applied in treating soft tissue injury,fresh closed fracture,limb dysfunction after fracture healing,shoulder,neck and leg pain,knee joint pain and other clinical multiple diseases for 30 years in clinical.However,research on the material basis of HHML for the treatment of fracture healing-related disorders is still in a gap.Therefore,it is particularly important to explore the active ingredients,core targets and potential pharmacological mechanisms of HHML to promote fracture healing.Methods:We screened the core active components of each traditional Chinese medicine in formula and its action targets through the Traditional Chinese Medicine Systems Pharmacology Database and Analysis Platform and Encyclopedia of Traditional Chinese Medicine database.The fracture related targets were retrieved from several different public databases,including GeneCards,Online Mendelian Inheritance in Man,DisGeNET and Therapeutic Target Database.Bioinformatics analysis to obtain key bioactive components,underlying targets and signaling pathways,containing the Venn diagram of the intersection with components and diseases gene targets,protein–protein interaction,as well as the Gene Ontology and the Kyoto Encyclopedia of Genes and Genomes analysis,and finally molecular docking.Results:A total of 249 bioactive ingredients of HHML and 325 HHML-fracture-related targets were screened.The network analysis revealed that quercetin,luteolin,kaempferol,Licochalcone A,naringenin and 8-Isopentenyl-kaempferol may be potential candidate agents.Multiple targets are involved including TP53,MAPK3,STAT3,AKT1,MAPK1,HSP90AA1,ESR1 and PIK3CA may be closely linked targets.PI3K-AKT signaling pathway may play a significant role of HHML in treatment of fracture.What’s more,molecular docking suggested that 8-isopentenyl kaempferol,glycyrrhiza chalcone A,and naringenin bound to AKT1,PIK3CA,and ESR1,respectively,exhibiting lower energy and more stable characteristics.Conclusions:The findings indicate the potential active ingredients,target proteins and molecular mechanisms of HHML for the treatment of fractures to provide the exact idea for the next research on the mechanism of action of HHML formula for fracture treatment.展开更多
Hot isostatic pressing parameters are critical to Ti60 high temperature titanium alloy castings which have wide application perspective in aerospace.In order to obtain optimal processing parameters,the effects of hot ...Hot isostatic pressing parameters are critical to Ti60 high temperature titanium alloy castings which have wide application perspective in aerospace.In order to obtain optimal processing parameters,the effects of hot isostatic pressing parameters on defects,composition uniformity,microstructure and mechanical properties of Ti60 cast high temperature titanium alloy were investigated in detail.Results show that increasing temperature and pressure of hot isostatic pressing can reduce defects,especially,the internal defects are substantially eliminated when the temperature exceeds 920℃or the pressure exceeds 125 MPa.The higher temperature and pressure can improve the microstructure uniformity.Besides,the higher pressure can promote the composition uniformity.With the temperature increases from 880℃to 960℃,α-laths are coarsened.But with increasing pressure,the grain size of prior-βphase,the widths ofα-laths andα-colony are reduced.The tensile strength of Ti60 alloy is 949 MPa,yield strength is 827 MPa,and the elongation is 11%when the hot isostatic pressing parameters are 960℃/125 MPa/2 h,which exhibits the best match between the strength and plasticity.展开更多
High-voltage LiCoO_(2)(LCO) is an attractive cathode for ultra-high energy density lithium-ion batteries(LIBs) in the 3 C markets.However,the sluggish lithium-ion diffusion at high voltage significantly hampers its ra...High-voltage LiCoO_(2)(LCO) is an attractive cathode for ultra-high energy density lithium-ion batteries(LIBs) in the 3 C markets.However,the sluggish lithium-ion diffusion at high voltage significantly hampers its rate capability.Herein,combining experiments with density functional theory(DFT) calculations,we demonstrate that the kinetic limitations can be mitigated by a facial Mg^(2+)+Gd^(3+)co-doping method.The as-prepared LCO shows significantly enhanced Li-ion diffusion mobility at high voltage,making more homogenous Li-ion de/intercalation at a high-rate charge/discharge process.The homogeneity enables the structural stability of LCO at a high-rate current density,inhibiting stress accumulation and irreversible phase transition.When used in combination with a Li metal anode,the doped LCO shows an extreme fast charging(XFC) capability,with a superior high capacity of 193.1 mAh g^(-1)even at the current density of 20 C and high-rate capacity retention of 91.3% after 100 cycles at 5 C.This work provides a new insight to prepare XFC high-voltage LCO cathode materials.展开更多
Evaluating the comprehensive characteristics of extreme ultraviolet(EUV)photoresists is crucial for their application in EUV lithography,a key process in modern technology.This paper highlights the capabilities of the...Evaluating the comprehensive characteristics of extreme ultraviolet(EUV)photoresists is crucial for their application in EUV lithography,a key process in modern technology.This paper highlights the capabilities of the Shanghai Synchrotron Radiation Facility(SSRF)08U1B beamline in advancing this field.Specifically,it demonstrates how this beamline can create fringe patterns with a 15-nm half-pitch on a resist using synchrotron-based EUV lithography.This achievement is vital for evaluating EUV photoresists at the advanced 5-nm node.We provide a detailed introduction to the methods and experimental setup used at the SSRF 08U1B beamline to assess an EUV photoresist.A significant part of this research involved the fabrication of high-resolution hydrogen silsesquioxane mask gratings.These gratings,with an aspect ratio of approximately 3,were created using electron beam lithography on an innovative mask framework.This framework was crucial in eliminating the impact of zeroth-order light on interference patterns.The proposed framework propose offers a new approach to mask fabrication,particularly beneficial for achromatic Talbot lithography and multicoherent-beam interference applications.展开更多
Sediment collapse and subsequent lateral downslope migration play important roles in shaping the habitats and regulating sedimentary organic carbon(SOC)cycling in hadal trenches.In this study,three sediment cores were...Sediment collapse and subsequent lateral downslope migration play important roles in shaping the habitats and regulating sedimentary organic carbon(SOC)cycling in hadal trenches.In this study,three sediment cores were collected using a human-occupied vehicle across the axis of the southern Yap Trench(SYT).The total organic carbon(TOC)and total nitrogen(TN)contents,δ13C,radiocarbon ages,specific surface areas,and grain size compositions of sediments from three cores were measured.We explored the influence of the lateral downslope transport on the dispersal of the sediments and established a tentative box model for the SOC balance.In the SYT,the surface TOC content decreased with water depth and was decoupled by the funneling effect of the V-shaped hadal trench.However,the sedimentation(0.0025 cm/a)and SOC accumulation rates(∼0.038 g/(m^(2)·a)(in terms of OC))were approximately 50%higher in the deeper hadal region than in the abyssal region(0.0016 cm/a and∼0.026 g/(m^(2)·a)(in terms of OC),respectively),indicating the occurrence of lateral downslope transport.The fluctuating variations in the prokaryotic abundances and the SOC accumulation rate suggest the periodic input of surficial sediments from the shallow region.The similar average TOC(0.31%–0.38%),TN(0.06%–0.07%)contents,and SOC compositions(terrestrial OC(11%–18%),marine phytoplanktonic OC(45%–53%),and microbial OC(32%–44%))of the three sites indicate that the lateral downslope transport has a significant mixing effect on the SOC composition.The output fluxes of the laterally transported SOC(0.44–0.56 g/(m^(2)·a)(in terms of OC))contributed approximately(47%–73%)of the total SOC input,and this proportion increased with water depth.The results of this study demonstrate the importance of lateral downslope transport in the spatial distribution and development of biomes.展开更多
A novel Ti-5.55Al-6.70Zr-1.50V-0.70Mo-3.41Nb-0.21Si alloy was designed using the cluster formula approach(cluster-plus-glue-atom model)and prepared by laser melting deposition(LMD).Its composition formula 12[Al-Ti_(12...A novel Ti-5.55Al-6.70Zr-1.50V-0.70Mo-3.41Nb-0.21Si alloy was designed using the cluster formula approach(cluster-plus-glue-atom model)and prepared by laser melting deposition(LMD).Its composition formula 12[Al-Ti_(12)](AlTi_(2))+5[Al_(0.8)Si_(0.2)-Ti_(12)Zr_(2)](V_(0.8)Mo_(0.2)Nb_(1)Ti)features an enhancedβ-Ti via co-alloying of Zr,V,Mo,Nb and Si.The experimental results show that the cluster formula ofαandβphases in the novel alloy are respectivelyα-[Al-Ti_(11.5)Zr_(0.5)](Al_(1)Ti_(2))andβ-[Al_(0.8)Si_(0.2)-Ti_(13.2)Zr_(0.8)](V_(1)Mo_(0.4)Nb_(1.6)),both containing Zr elements.The fitted composition via the α andβphase cluster formulas has little difference with the actual alloy composition,suggesting that the validity of cluster-plus-glue-atom model in the alloy composition design.After hot isostatic pressing(HIP),both the Ti-6Al-4V and the novel alloy by LMD are characterized by prior-βcolumnar grains,while the typical<100>texture disappears.Compared with Ti-6Al-4V,Ti-5.55Al-6.70Zr-1.50V-0.70Mo-3.41Nb-0.21Si alloy exhibits a combination of higher strength(1,056 MPa)and higher ductility(14%)at room temperature and higher strength(580 MPa)at 550℃ after HIP,and can potentially serves as LMD materials.展开更多
Ni-rich layered oxides are one of the most promising cathode materials for Li-ion batteries due to their high energy density.However,the chemomechanical breakdown and capacity degradation associated with the anisotrop...Ni-rich layered oxides are one of the most promising cathode materials for Li-ion batteries due to their high energy density.However,the chemomechanical breakdown and capacity degradation associated with the anisotropic lattice evolution during lithiation/delithiation hinders its practical application.Herein,by utilizing the in situ environmental transmission electron microscopy(ETEM),we provide a real time nanoscale characterization of high temperature solid-state synthesis of LiNi_(0.8)CO_(0.1)Mn_(0.1)O_(2)(NCM811) cathode,and unprecedentedly reveal the strain/stress formation and morphological evolution mechanism of primary/second ary particles,as well as their influence on electrochemical performance.We show that stress inhomogeneity during solid-state synthesis will lead to both primary/secondary particle pulverization and new grain boundary initiation,which are detrimental to cathode cycling stability and rate performance.Aiming to alleviate this multiscale strain during solid-state synthesis,we introduced a calcination scheme that effectively relieves the stress during the synthesis,thus mitigating the primary/secondary particle crack and the detrimental grain boundaries formation,which in turn improves the cathode structural integrity and Li-ion transport kinetics for long-life and high-rate electrochemical performance.This work remarkably advances the fundamental understanding on mechanochemical properties of transition metal oxide cathode with solid-state synthesis and provides a unified guide for optimization the Ni-rich oxide cathode.展开更多
The in situ(TiC+TiB)/TA15 composites with different volume percentages of reinforcement(10%,15%,20%and 25%)were prepared by water-cooled copper crucible vacuum suspension melting technology.The structures and composit...The in situ(TiC+TiB)/TA15 composites with different volume percentages of reinforcement(10%,15%,20%and 25%)were prepared by water-cooled copper crucible vacuum suspension melting technology.The structures and compositions of the TA15 alloy and its composites were analyzed by XRD and EDS,and their electrochemical corrosion behaviors in the 3.5%NaCl solution were studied.Corrosion wear testing was conducted using a reciprocating ball-on-disc wear tester under a 10 N load.Results show that the in situ fibrous TiB phase and the granular TiC phase are uniformly distributed on the composite matrix.The microhardness can reach up to 531 HV as 25vol.%TiC+TiB reinforcement is added.Compared with the TA15 alloy,the volume wear rate decreases from(2.21±0.07)×10^(-4)to(1.75±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1)by adding 15vol.%TiC+TiB reinforcement,and the wear mechanism is adhesive wear.When the volume percentage of the reinforcement phase reaches 25%,the volume wear rate increases from(1.75±0.07)×10^(-4)to(2.41±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1),and the wear mechanism changes into abrasive wear.The volume loss resulted by the interaction between corrosion and wear accounts for more than 27%of the total wear volume.The volume loss due to wear-induced corrosion changes from 1.94%to 4.06%with different additions of reinforcement.The volume loss caused by corrosion-induced wear initially increases from 24.08%to 26.90%as the reinforcement increases from 0 to 15%due to the increase of corrosion potential,and then decreases from 26.90%to 25.68%as the reinforcement increases from 15%to 25%due to the peeling of TiC phase.展开更多
Mg-3Al-1Zn(AZ31)sheets were produced by transverse gradient extrusion(TGE)process.The flow behavior and dynamic recrystallization during extrusion were systematically analyzed.The microstructures,textures,and mechanic...Mg-3Al-1Zn(AZ31)sheets were produced by transverse gradient extrusion(TGE)process.The flow behavior and dynamic recrystallization during extrusion were systematically analyzed.The microstructures,textures,and mechanical behavior of extruded AZ31 sheet were also analyzed and compared with conventional extruded(CE)sheet.The results showed that fine grain structure and multi-type unique textures were formed in TGE sheet because of the generation of extra flow velocity along transverse direction(TD)and flow velocity gradient along extrusion direction(ED)during extrusion.The basal poles gradually deviated away normal direction(ND)from edge to center of the TGE sheet along TD,and the largest inclination angle at center region reached around 65°.Furthermore,the basal poles inclined from ED to TD 40°-63°,except for the center region of TGE sheet.The TGE sheet presented higher ductility and strain hardening exponent(n-value),but lower yield strength and Lankford value(r-value)in comparison with the CE sheet.Both the basal<a>slip and tensile twins were easy to be activated during deformation,and the largest elongation of 41%and the lowest yield strength of 86.5 MPa were obtained for the ED-center sample in the TGE sheet.展开更多
Interstitial fluid plays a vital role in drug delivery and tumour treatment.However,few non-invasive measurement methods are available for measuring low-velocity biological fluid flow.Therefore,this study aimed to dev...Interstitial fluid plays a vital role in drug delivery and tumour treatment.However,few non-invasive measurement methods are available for measuring low-velocity biological fluid flow.Therefore,this study aimed to develop a novel technology called interstitial flow velocity-MRI.The interstitial flow velocity-MRI sequence consists of a dual inversion recovery preparation and an improved stimulated echo sequence(ISTE)combined with phase-contrast MRI.A homemade flow phantom was used to assess the feasibility and sensitivity of interstitial flow velocity-MRI.In addition,xenografts of female BALB/c mouse models of 4T1 breast cancer administered losartan(40 mg/kg)or saline(n?6)were subjected to imaging on a 7.0 T scanner to assess the in vivo interstitial fluid flow velocity.The results showed a significant correlation(P<0.001)between the theoretical velocities and velocities measured using the flow phantom.Interstitial flow velocity-MRI could detect a velocity as low as 10.21±2.65 mm/s with a spatial resolution of 0.313 mm.The losartan group had a lower mean interstitial fluid velocity than the control group(85±16 vs 113±24 mm/s).In addition,compared to the saline treatment,losartan treatment reduced the proportion of collagen fibres by 10%and 12%in the Masson and Sirius red staining groups,respectively.Interstitial flow velocity-MRI has the potential to determine interstitial fluid flow velocity non-invasively and exhibits an intuitive velocity map.展开更多
基金financially supported by the National Key Research&Development Program of China(Nos.2020YFB2008300,2020YFB2008303)。
文摘Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength,low density,and high modulus.In this study,the TA15-based composites reinforced with a volume fraction of 10% to 25%(TiB+TiC)were prepared using powder metallurgy and casting technique.Microstructural characterization and phase constitution were examined using optical microscopy(OM),scanning electron microscopy(SEM),and X-ray diffraction(XRD).In addition,the microhardness,room temperature(RT)and high temperature(HT)tensile properties of the composites were evaluated.Results revealed that the reinforcements are distributed uniformly even in the composites with a high volume of TiB and TiC.However,as the volume fraction exceeds 15%,TiB and TiC particles become coarsening and exhibit rod-like and dendritic-like morphology.Microhardness increases gradually from 321.2 HV for the base alloy to a maximum of 473.3 HV as the reinforcement increases to 25vol.%.Tensile test results indicate that a reinforcement volume fraction above 20% is beneficial for enhancing tensile strength and yield strength at high temperatures,but it has an adverse effect on room temperature elongation.Conversely,if the reinforcement volume fraction is below 20%,it can improve high-temperature elongation when the temperature exceeds 600℃.
基金supported by the CACMS Innovation Fund(CI2021A00914)the Beijing Novaprogram(Z211100002121062)+1 种基金the Opening Project of the Key Laboratory of Integrative Chinese and Western Medicine for the Diagnosis and Treatment of Circulatory Diseases of Zhejiang Province(2C32001)the National Natural Science Foundation of China(82004193)。
文摘The Mediterranean diet has long been recognized as one of the most effective ways to prevent and improve cardiovascular disease.Extra virgin olive oil(EVOO)is the typical sources of fat in the Mediterranean diet which have been shown to have noteworthy nutritional value and positive impact on human health.It is worth noting that EVOO owes its superior nutritional value to its bioactive composition.The main component of EVOO is monounsaturated fatty acids(MUFAs)in the form of oleic acid.Oleic acid accounts for up to 70%-80%of EVOO.Secondly,EVOO contains approximately more than 30 phenolic compounds,of which HT is essential for the protection against cardiovascular diseases.In this review,we focused on the potential mechanisms of oleic acid and polyphenols combat cardiovascular diseases risk in terms of oxidative stress,inflammation,blood pressure,endothelial function and cholesterol.This review might provide a reference for the studies on cardiovascular protective effects of EVOO.
基金Supported by the Science,Technology and Innovation Commission of Shenzhen Municipality(No.GJHZ20220913142618036,No.JCYJ20210324113610029).
文摘●AIM:To identify disease-causative mutations in families with congenital cataract.●METHODS:Two Chinese families with autosomaldominant congenital cataract(ADCC)were recruited and underwent comprehensive eye examinations.Gene panel next-generation sequencing of common pathogenic genes of congenital cataract was performed in the proband of each family.Sanger sequencing was used to valid the candidate gene mutations and sequence the other family members for co-segregation analysis.The effect of sequence changes on protein structure and function was predicted through bioinformatics analysis.Major intrinsic protein(MIP)-wildtype and MIP-G29R plasmids were constructed and microinjected into zebrafish single-cell stage embryos.Zebrafish embryonic lens phenotypes were screened using confocal microscopy.●RESULTS:A novel heterozygous mutation(c.85G>A;p.G29R)in the MIP gene was identified in the proband of one family.A known heterozygous mutation(c.97C>T;p.R33C;rs864309693)in MIP was found in the proband of another family.In-silico prediction indicated that the novel mutation might affect the MIP protein function.Zebrafish embryonic lens was uniformly transparent in both wild-type PCS2+MIP and mutant PCS2+MIP.●CONCLUSION:Two missense mutations in the MIP gene in Chinese cataract families are identified,and one of which is novel.These findings expand the genetic spectrum of MIP mutations associated with cataracts.The functional studies suggest that the novel MIP mutation might not be a gain-of-function but a loss-of-function mutation.
基金supported by the Science and Technology Project of State Grid Shanxi Electric Power Research Institute:Research on Data-Driven New Power System Operation Simulation and Multi Agent Control Strategy(52053022000F).
文摘Due to the impact of source-load prediction power errors and uncertainties,the actual operation of the park will have a wide range of fluctuations compared with the expected state,resulting in its inability to achieve the expected economy.This paper constructs an operating simulation model of the park power grid operation considering demand response and proposes a multi-time scale operating simulation method that combines day-ahead optimization and model predictive control(MPC).In the day-ahead stage,an operating simulation plan that comprehensively considers the user’s side comfort and operating costs is proposed with a long-term time scale of 15 min.In order to cope with power fluctuations of photovoltaic,wind turbine and conventional load,MPC is used to track and roll correct the day-ahead operating simulation plan in the intra-day stage to meet the actual operating operation status of the park.Finally,the validity and economy of the operating simulation strategy are verified through the analysis of arithmetic examples.
基金This work was supported by the Project of State Administration of Traditional Chinese Medicine of Sichuan Province of China(No.2021MS407).
文摘Background:Hai Honghua medicinal liquor(HHML),a famous hospital formula composed of 19 traditional Chinese medicines,has been successfully applied in treating soft tissue injury,fresh closed fracture,limb dysfunction after fracture healing,shoulder,neck and leg pain,knee joint pain and other clinical multiple diseases for 30 years in clinical.However,research on the material basis of HHML for the treatment of fracture healing-related disorders is still in a gap.Therefore,it is particularly important to explore the active ingredients,core targets and potential pharmacological mechanisms of HHML to promote fracture healing.Methods:We screened the core active components of each traditional Chinese medicine in formula and its action targets through the Traditional Chinese Medicine Systems Pharmacology Database and Analysis Platform and Encyclopedia of Traditional Chinese Medicine database.The fracture related targets were retrieved from several different public databases,including GeneCards,Online Mendelian Inheritance in Man,DisGeNET and Therapeutic Target Database.Bioinformatics analysis to obtain key bioactive components,underlying targets and signaling pathways,containing the Venn diagram of the intersection with components and diseases gene targets,protein–protein interaction,as well as the Gene Ontology and the Kyoto Encyclopedia of Genes and Genomes analysis,and finally molecular docking.Results:A total of 249 bioactive ingredients of HHML and 325 HHML-fracture-related targets were screened.The network analysis revealed that quercetin,luteolin,kaempferol,Licochalcone A,naringenin and 8-Isopentenyl-kaempferol may be potential candidate agents.Multiple targets are involved including TP53,MAPK3,STAT3,AKT1,MAPK1,HSP90AA1,ESR1 and PIK3CA may be closely linked targets.PI3K-AKT signaling pathway may play a significant role of HHML in treatment of fracture.What’s more,molecular docking suggested that 8-isopentenyl kaempferol,glycyrrhiza chalcone A,and naringenin bound to AKT1,PIK3CA,and ESR1,respectively,exhibiting lower energy and more stable characteristics.Conclusions:The findings indicate the potential active ingredients,target proteins and molecular mechanisms of HHML for the treatment of fractures to provide the exact idea for the next research on the mechanism of action of HHML formula for fracture treatment.
基金financially supported by the National Key Research and Development Program of China(Grant No.2020YFB2008300)。
文摘Hot isostatic pressing parameters are critical to Ti60 high temperature titanium alloy castings which have wide application perspective in aerospace.In order to obtain optimal processing parameters,the effects of hot isostatic pressing parameters on defects,composition uniformity,microstructure and mechanical properties of Ti60 cast high temperature titanium alloy were investigated in detail.Results show that increasing temperature and pressure of hot isostatic pressing can reduce defects,especially,the internal defects are substantially eliminated when the temperature exceeds 920℃or the pressure exceeds 125 MPa.The higher temperature and pressure can improve the microstructure uniformity.Besides,the higher pressure can promote the composition uniformity.With the temperature increases from 880℃to 960℃,α-laths are coarsened.But with increasing pressure,the grain size of prior-βphase,the widths ofα-laths andα-colony are reduced.The tensile strength of Ti60 alloy is 949 MPa,yield strength is 827 MPa,and the elongation is 11%when the hot isostatic pressing parameters are 960℃/125 MPa/2 h,which exhibits the best match between the strength and plasticity.
基金supported by the National Key R&D Program of China(2020YFA0406203)the Shenzhen Science and Technology Innovation Commission(JCYJ20180507181806316,JCYJ20200109105618137)+1 种基金the ECS Scheme(City U 21307019,City U7020043,City U7005500,City U7005612)the Shenzhen Research Institute,City University of Hong Kong。
文摘High-voltage LiCoO_(2)(LCO) is an attractive cathode for ultra-high energy density lithium-ion batteries(LIBs) in the 3 C markets.However,the sluggish lithium-ion diffusion at high voltage significantly hampers its rate capability.Herein,combining experiments with density functional theory(DFT) calculations,we demonstrate that the kinetic limitations can be mitigated by a facial Mg^(2+)+Gd^(3+)co-doping method.The as-prepared LCO shows significantly enhanced Li-ion diffusion mobility at high voltage,making more homogenous Li-ion de/intercalation at a high-rate charge/discharge process.The homogeneity enables the structural stability of LCO at a high-rate current density,inhibiting stress accumulation and irreversible phase transition.When used in combination with a Li metal anode,the doped LCO shows an extreme fast charging(XFC) capability,with a superior high capacity of 193.1 mAh g^(-1)even at the current density of 20 C and high-rate capacity retention of 91.3% after 100 cycles at 5 C.This work provides a new insight to prepare XFC high-voltage LCO cathode materials.
基金supported by the National Key Research and Development Program of China(Nos.2021YFA1601003,2017YFA0206002,2017YFA0403400)the National Natural Science Foundation of China(No.11775291)。
文摘Evaluating the comprehensive characteristics of extreme ultraviolet(EUV)photoresists is crucial for their application in EUV lithography,a key process in modern technology.This paper highlights the capabilities of the Shanghai Synchrotron Radiation Facility(SSRF)08U1B beamline in advancing this field.Specifically,it demonstrates how this beamline can create fringe patterns with a 15-nm half-pitch on a resist using synchrotron-based EUV lithography.This achievement is vital for evaluating EUV photoresists at the advanced 5-nm node.We provide a detailed introduction to the methods and experimental setup used at the SSRF 08U1B beamline to assess an EUV photoresist.A significant part of this research involved the fabrication of high-resolution hydrogen silsesquioxane mask gratings.These gratings,with an aspect ratio of approximately 3,were created using electron beam lithography on an innovative mask framework.This framework was crucial in eliminating the impact of zeroth-order light on interference patterns.The proposed framework propose offers a new approach to mask fabrication,particularly beneficial for achromatic Talbot lithography and multicoherent-beam interference applications.
基金The Scientific Research Fund of the Second Institute of Oceanography under contract Nos JG2011 and JG1516the National Natural Science Foundation of China under contract No.41606090the National Basic Research Program(973 Program)of China under contract No.2015CB755904.
文摘Sediment collapse and subsequent lateral downslope migration play important roles in shaping the habitats and regulating sedimentary organic carbon(SOC)cycling in hadal trenches.In this study,three sediment cores were collected using a human-occupied vehicle across the axis of the southern Yap Trench(SYT).The total organic carbon(TOC)and total nitrogen(TN)contents,δ13C,radiocarbon ages,specific surface areas,and grain size compositions of sediments from three cores were measured.We explored the influence of the lateral downslope transport on the dispersal of the sediments and established a tentative box model for the SOC balance.In the SYT,the surface TOC content decreased with water depth and was decoupled by the funneling effect of the V-shaped hadal trench.However,the sedimentation(0.0025 cm/a)and SOC accumulation rates(∼0.038 g/(m^(2)·a)(in terms of OC))were approximately 50%higher in the deeper hadal region than in the abyssal region(0.0016 cm/a and∼0.026 g/(m^(2)·a)(in terms of OC),respectively),indicating the occurrence of lateral downslope transport.The fluctuating variations in the prokaryotic abundances and the SOC accumulation rate suggest the periodic input of surficial sediments from the shallow region.The similar average TOC(0.31%–0.38%),TN(0.06%–0.07%)contents,and SOC compositions(terrestrial OC(11%–18%),marine phytoplanktonic OC(45%–53%),and microbial OC(32%–44%))of the three sites indicate that the lateral downslope transport has a significant mixing effect on the SOC composition.The output fluxes of the laterally transported SOC(0.44–0.56 g/(m^(2)·a)(in terms of OC))contributed approximately(47%–73%)of the total SOC input,and this proportion increased with water depth.The results of this study demonstrate the importance of lateral downslope transport in the spatial distribution and development of biomes.
基金supported by the Natural Science Foundation of Shenyang,China(Grant No.22315605).
文摘A novel Ti-5.55Al-6.70Zr-1.50V-0.70Mo-3.41Nb-0.21Si alloy was designed using the cluster formula approach(cluster-plus-glue-atom model)and prepared by laser melting deposition(LMD).Its composition formula 12[Al-Ti_(12)](AlTi_(2))+5[Al_(0.8)Si_(0.2)-Ti_(12)Zr_(2)](V_(0.8)Mo_(0.2)Nb_(1)Ti)features an enhancedβ-Ti via co-alloying of Zr,V,Mo,Nb and Si.The experimental results show that the cluster formula ofαandβphases in the novel alloy are respectivelyα-[Al-Ti_(11.5)Zr_(0.5)](Al_(1)Ti_(2))andβ-[Al_(0.8)Si_(0.2)-Ti_(13.2)Zr_(0.8)](V_(1)Mo_(0.4)Nb_(1.6)),both containing Zr elements.The fitted composition via the α andβphase cluster formulas has little difference with the actual alloy composition,suggesting that the validity of cluster-plus-glue-atom model in the alloy composition design.After hot isostatic pressing(HIP),both the Ti-6Al-4V and the novel alloy by LMD are characterized by prior-βcolumnar grains,while the typical<100>texture disappears.Compared with Ti-6Al-4V,Ti-5.55Al-6.70Zr-1.50V-0.70Mo-3.41Nb-0.21Si alloy exhibits a combination of higher strength(1,056 MPa)and higher ductility(14%)at room temperature and higher strength(580 MPa)at 550℃ after HIP,and can potentially serves as LMD materials.
基金the funding support from the National Natural Science Foundation of China (Nos. 52022088, 51971245, 51772262, U20A20336, 21935009)the National Key R&D Program of China (No. 2022YFB2404300, 2022YFE0207900)+2 种基金the Natural Science Foundation of Hebei Province (No. F2021203097, B2020203037)the China Postdoctoral Science Foundation (Grant number 2021M702756)the Sichuan Science and Technology Program and Science and Technology Planning Project of Yibin Sanjiang New Area (2022JBGS002, 2022ZYD0125, 23QYCX0034, 2021ZYGY022)。
文摘Ni-rich layered oxides are one of the most promising cathode materials for Li-ion batteries due to their high energy density.However,the chemomechanical breakdown and capacity degradation associated with the anisotropic lattice evolution during lithiation/delithiation hinders its practical application.Herein,by utilizing the in situ environmental transmission electron microscopy(ETEM),we provide a real time nanoscale characterization of high temperature solid-state synthesis of LiNi_(0.8)CO_(0.1)Mn_(0.1)O_(2)(NCM811) cathode,and unprecedentedly reveal the strain/stress formation and morphological evolution mechanism of primary/second ary particles,as well as their influence on electrochemical performance.We show that stress inhomogeneity during solid-state synthesis will lead to both primary/secondary particle pulverization and new grain boundary initiation,which are detrimental to cathode cycling stability and rate performance.Aiming to alleviate this multiscale strain during solid-state synthesis,we introduced a calcination scheme that effectively relieves the stress during the synthesis,thus mitigating the primary/secondary particle crack and the detrimental grain boundaries formation,which in turn improves the cathode structural integrity and Li-ion transport kinetics for long-life and high-rate electrochemical performance.This work remarkably advances the fundamental understanding on mechanochemical properties of transition metal oxide cathode with solid-state synthesis and provides a unified guide for optimization the Ni-rich oxide cathode.
基金This work was financially supported by the National Key Research and Development Program of China(Grant Nos.2020YFB2008305,2020YFB2008303)the Natural Science Foundation of Shenyang City(Grant No.22315605).
文摘The in situ(TiC+TiB)/TA15 composites with different volume percentages of reinforcement(10%,15%,20%and 25%)were prepared by water-cooled copper crucible vacuum suspension melting technology.The structures and compositions of the TA15 alloy and its composites were analyzed by XRD and EDS,and their electrochemical corrosion behaviors in the 3.5%NaCl solution were studied.Corrosion wear testing was conducted using a reciprocating ball-on-disc wear tester under a 10 N load.Results show that the in situ fibrous TiB phase and the granular TiC phase are uniformly distributed on the composite matrix.The microhardness can reach up to 531 HV as 25vol.%TiC+TiB reinforcement is added.Compared with the TA15 alloy,the volume wear rate decreases from(2.21±0.07)×10^(-4)to(1.75±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1)by adding 15vol.%TiC+TiB reinforcement,and the wear mechanism is adhesive wear.When the volume percentage of the reinforcement phase reaches 25%,the volume wear rate increases from(1.75±0.07)×10^(-4)to(2.41±0.07)×10^(-4)mm^(3)·N^(-1)·m^(-1),and the wear mechanism changes into abrasive wear.The volume loss resulted by the interaction between corrosion and wear accounts for more than 27%of the total wear volume.The volume loss due to wear-induced corrosion changes from 1.94%to 4.06%with different additions of reinforcement.The volume loss caused by corrosion-induced wear initially increases from 24.08%to 26.90%as the reinforcement increases from 0 to 15%due to the increase of corrosion potential,and then decreases from 26.90%to 25.68%as the reinforcement increases from 15%to 25%due to the peeling of TiC phase.
基金financially supported by the Guangdong Academy of Science Fund(No.2020GDASYL-20200101001)the Guangdong Major Project of Basic and Applied Basic Research(No.2020B0301030006)+4 种基金the China Postdoctoral Science Foundation(No.2022M720858)the Scientific Research Fund of Hunan Provincial Education Department(No.21B0726)the National Natural Science Foundation of China(Nos.U1764253,51971044,U1910213,52001037,and U207601)the Qinghai Scientific&Technological Program(No.2018-GX-A1)the Natural Science Foundation of Chongqing,China(No.cstc2019jcyjmsxmX0234).
文摘Mg-3Al-1Zn(AZ31)sheets were produced by transverse gradient extrusion(TGE)process.The flow behavior and dynamic recrystallization during extrusion were systematically analyzed.The microstructures,textures,and mechanical behavior of extruded AZ31 sheet were also analyzed and compared with conventional extruded(CE)sheet.The results showed that fine grain structure and multi-type unique textures were formed in TGE sheet because of the generation of extra flow velocity along transverse direction(TD)and flow velocity gradient along extrusion direction(ED)during extrusion.The basal poles gradually deviated away normal direction(ND)from edge to center of the TGE sheet along TD,and the largest inclination angle at center region reached around 65°.Furthermore,the basal poles inclined from ED to TD 40°-63°,except for the center region of TGE sheet.The TGE sheet presented higher ductility and strain hardening exponent(n-value),but lower yield strength and Lankford value(r-value)in comparison with the CE sheet.Both the basal<a>slip and tensile twins were easy to be activated during deformation,and the largest elongation of 41%and the lowest yield strength of 86.5 MPa were obtained for the ED-center sample in the TGE sheet.
文摘Interstitial fluid plays a vital role in drug delivery and tumour treatment.However,few non-invasive measurement methods are available for measuring low-velocity biological fluid flow.Therefore,this study aimed to develop a novel technology called interstitial flow velocity-MRI.The interstitial flow velocity-MRI sequence consists of a dual inversion recovery preparation and an improved stimulated echo sequence(ISTE)combined with phase-contrast MRI.A homemade flow phantom was used to assess the feasibility and sensitivity of interstitial flow velocity-MRI.In addition,xenografts of female BALB/c mouse models of 4T1 breast cancer administered losartan(40 mg/kg)or saline(n?6)were subjected to imaging on a 7.0 T scanner to assess the in vivo interstitial fluid flow velocity.The results showed a significant correlation(P<0.001)between the theoretical velocities and velocities measured using the flow phantom.Interstitial flow velocity-MRI could detect a velocity as low as 10.21±2.65 mm/s with a spatial resolution of 0.313 mm.The losartan group had a lower mean interstitial fluid velocity than the control group(85±16 vs 113±24 mm/s).In addition,compared to the saline treatment,losartan treatment reduced the proportion of collagen fibres by 10%and 12%in the Masson and Sirius red staining groups,respectively.Interstitial flow velocity-MRI has the potential to determine interstitial fluid flow velocity non-invasively and exhibits an intuitive velocity map.
