The wear rate between the rotors of a hypotrochoidal gear pump is characterized.Using the knowledge of shape design on the rotors,the contact stresses without hydrodynamic effect between the rotor teeth were evaluated...The wear rate between the rotors of a hypotrochoidal gear pump is characterized.Using the knowledge of shape design on the rotors,the contact stresses without hydrodynamic effect between the rotor teeth were evaluated through the calculation of the Hertzian contact stress.Based on the above results and the sliding velocity between the rotors,a genetic algorithm (GA) was used as an optimization technique forminimizing the wear rate proportional factor (WRPF).The result shows that the wear rate or the WRPF can be reduced considerably,e.g.approximately 12.8%,throughout the optimization using GA.展开更多
The most conventional vehicle pretensioner system consists of an internal gear pair with involute teeth. However, it has been well known that the corresponding gear pairs are relatively weak under the situation of imp...The most conventional vehicle pretensioner system consists of an internal gear pair with involute teeth. However, it has been well known that the corresponding gear pairs are relatively weak under the situation of impact loadings. To improve this phenomenon, a new pretensioning gear system with cycloid teeth rather than the involute ones was proposed, and dual cycloidal gear mechanisms were designed for satisfying geometric constraints and dynamic loading conditions. The simulations of the prototypes were conducted by LS-DYNA program and the experiments for a prototype were performed for a dynamic model with impact loading devices. The results show that the better operation and the smoother motion are confirmed in the proposed cycloidal gear system rather than the conventional one without interferences between gear teeth under the impact of a crash.展开更多
A roller rack pinion(RRP)system,which consists of a rack-bar and a cam pinion,transforms a rotation motion into linear motion.The rack-bar has a series of roller train and meshes with the cam pinion.First,the exact to...A roller rack pinion(RRP)system,which consists of a rack-bar and a cam pinion,transforms a rotation motion into linear motion.The rack-bar has a series of roller train and meshes with the cam pinion.First,the exact tooth profile of the cam pinion and the non-undercut condition to satisfy the required performance have been proposed with the introduction of the profile shift coefficient.Then,the load stress factors are investigated under the variation of the shape design parameters to predict the gear surface fatigue limit which is strongly related to the gear noise and vibration at the contact patch.The results show that the pitting life can be extended significantly with the increase of the profile shift coefficient.展开更多
基金supported by Changwon National University in 2010,Korea
文摘The wear rate between the rotors of a hypotrochoidal gear pump is characterized.Using the knowledge of shape design on the rotors,the contact stresses without hydrodynamic effect between the rotor teeth were evaluated through the calculation of the Hertzian contact stress.Based on the above results and the sliding velocity between the rotors,a genetic algorithm (GA) was used as an optimization technique forminimizing the wear rate proportional factor (WRPF).The result shows that the wear rate or the WRPF can be reduced considerably,e.g.approximately 12.8%,throughout the optimization using GA.
基金supported by the Changwon National University in 2011-2012,Korea
文摘The most conventional vehicle pretensioner system consists of an internal gear pair with involute teeth. However, it has been well known that the corresponding gear pairs are relatively weak under the situation of impact loadings. To improve this phenomenon, a new pretensioning gear system with cycloid teeth rather than the involute ones was proposed, and dual cycloidal gear mechanisms were designed for satisfying geometric constraints and dynamic loading conditions. The simulations of the prototypes were conducted by LS-DYNA program and the experiments for a prototype were performed for a dynamic model with impact loading devices. The results show that the better operation and the smoother motion are confirmed in the proposed cycloidal gear system rather than the conventional one without interferences between gear teeth under the impact of a crash.
基金Research financially supported by Changwon National University in 2011-2012,Korea
文摘A roller rack pinion(RRP)system,which consists of a rack-bar and a cam pinion,transforms a rotation motion into linear motion.The rack-bar has a series of roller train and meshes with the cam pinion.First,the exact tooth profile of the cam pinion and the non-undercut condition to satisfy the required performance have been proposed with the introduction of the profile shift coefficient.Then,the load stress factors are investigated under the variation of the shape design parameters to predict the gear surface fatigue limit which is strongly related to the gear noise and vibration at the contact patch.The results show that the pitting life can be extended significantly with the increase of the profile shift coefficient.
