A novel lightweight,radiation-shielding Mg-Ta-Al layered metal-matrix composite(LMC)was successful designed by doping the extremely refractory metal(Ta)into Mg sheets.These Mg-based LMCs sheets shows excellent radiati...A novel lightweight,radiation-shielding Mg-Ta-Al layered metal-matrix composite(LMC)was successful designed by doping the extremely refractory metal(Ta)into Mg sheets.These Mg-based LMCs sheets shows excellent radiation-dose shield effect,about 145 krad·a^(−1),which is about 17 times of traditional Mg alloy,while its surface density is only about 0.9 g·cm^(−2),reducing by 60%than that of pure Ta.The quantitate relationship between radiation-dose and the materials’thickness was also confirmed to the logistic function when the surface density is in the range of 0.6-1.5 g·cm^(−2).Meantime,the rolling parameters,interface microstructure and mechanical properties in both as-rolled and annealing treated samples were evaluated.The sheets possess a special dissimilar atoms diffusion transitional zone containing an obvious inter-diffusion Mg-Al interface and the unique micro-corrugated Ta-Al interface,as well as a thin Al film with a thickness of about 10μm.The special zone could reduce the stress concentration and enhance the strength of Mg-Ta-Al LMCs.The interface bonding strength reaches up to 54-76 MPa.The ultimate tensile strength(UTS)and yield strength(TYS)of the Mg-Ta-Al sheet were high to 413 MPa and 263 MPa,respectively,along with an elongation of 5.8%.The molecular dynamics(MD)analysis results show that the two interfaces exhibit different formation mechanism,the Mg-Al interface primarily depended on Mg/Al atoms diffusion basing point defects movement,while the Ta-Al interface with a micro-interlock pining shape formed by close-packed planes slipping during high temperature strain-induced deformation process.展开更多
The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show ...The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.展开更多
Compared with conventional forming processes,ultrasonic-assisted forming technology with a high frequency and small amplitude can significantly improve the forming quality of materials.Owing to the advantages of reduc...Compared with conventional forming processes,ultrasonic-assisted forming technology with a high frequency and small amplitude can significantly improve the forming quality of materials.Owing to the advantages of reduced forming force,improved surface quality,avoidance of forming defects,and strengthened surface structure,ultrasonic-assisted forming technology has been applied to increasingly advanced forming processes,such as incremental forming,spinning,and micro-forming.However,in the ultrasonic-assisted forming process,there are multiple ultrasonic mechanisms,such as the volume effect and surface effect.The explanation of the effect of ultrasonic vibration(UV)on plastic deformation remains controversial,hindering the development of related technologies.Recently,many researchers have proposed many new theories and technologies for ultrasonic-assisted forming.To summarize these developments,systematic discussions on mechanisms,theoretical models,and forming performances are provided in this review.On this basis,the limitations of the current study are discussed.In addition,an outlook for ultrasonic-assisted forming is proposed:efficient and stable UV systems,difficulty forming components with complex geometry,explanation of the in-depth mechanism,a systematic theoretical prediction model,and multi-field-coupling energy-assisted forming are considered to be hot spots in future studies.The present review enhances existing knowledge of ultrasonic-assisted forming,and facilitates a fast reference for related researchers.展开更多
To reveal the affecting mechanism of cooling rate on lamellarαprecipitation,the precipitation behaviors of lamellarαphase in IMI834 titanium alloy during isothermal and non-isothermal heat treatments were quantitati...To reveal the affecting mechanism of cooling rate on lamellarαprecipitation,the precipitation behaviors of lamellarαphase in IMI834 titanium alloy during isothermal and non-isothermal heat treatments were quantitatively characterized using experimental analysis.Critical precipitation temperatures at various cooling rates were obtained using thermal dilatation testing.Using metallographic microscopy,electron microprobe analysis,and data fitting methods,the quantitative evolution models of average width,volume fraction,and solute concentration in theαandβphases were built for different temperatures or cooling rates.A comparison between the two precipitation behaviors showed that the average width and volume fraction of lamellarαphase under non-isothermal conditions were smaller than those under isothermal conditions.With increasing cooling rate,the average width and volume fraction were decreased significantly,and the critical precipitation temperatures were reduced.This phenomenon is mainly attributed to the decreased diffusion velocity of solutes Al,Mo,and Nb with increasing cooling rate.展开更多
The quenching-spinning(Q-S)process,i.e.,shear spinning after blank quenching,has been increasingly utilized to form 2219 aluminum alloy complex thin-walled components.However,the changes in material property,shape and...The quenching-spinning(Q-S)process,i.e.,shear spinning after blank quenching,has been increasingly utilized to form 2219 aluminum alloy complex thin-walled components.However,the changes in material property,shape and stress of the blanks after quenching will affect the spin-ning forming precision.In this study,the rules and mechanisms of these effects are investigated based on a combined finite element(FE)model including blank quenching and component spinning process.The results indicate that the increase of material strength and the existence of distortion of the quenched blank lead to a notable increase in the non-uniformity of the circumferential compres-sive stress in the spinning area and the increase of the flange swing height during spinning.These changes result in an increase in the wall thickness and component-mandrel gap of the components.The quenching residual stress has little effect on wall thickness and roundness but can noticeably reduce the component-mandrel gap.This is because that the existence of quenching residual stress of the blank can lead to the decrease of the maximum circumferential compressive stress of the workpiece in spinning and an obvious drop in the maximum compressive stress after reaching the stress peak.Quenching distortion is the main factor affecting the roundness.Moreover,the opti-mized installation way of the blank for spinning is obtained.展开更多
Titanium alloys have been widely used in many industrial clusters such as automotive, aerospace and biomedical industries due to their excellent comprehensive properties. In order to obtain fine microstructures and fa...Titanium alloys have been widely used in many industrial clusters such as automotive, aerospace and biomedical industries due to their excellent comprehensive properties. In order to obtain fine microstructures and favorable properties, a well-designed multi-step thermomechanical processing(TMP) is critically needed in manufacturing of titanium components. In making of titanium components,subtransus processing is a critical step to breakdown lamellar microstructure to fine-structure in hot working process and thus plays a key role in tailoring the final microstructure and properties. To realize this goal, huge efforts have been made to investigate the mechanisms of microstructure evolution and flow behavior during the subtransus processing. This paper reviews the recent experimental and modelling progresses, which aim to provide some guidelines for the process design and microstructure tailoring for titanium alloy research community. The characteristics of the initial lamellar microstructure are presented, followed by the discussion on microstructure evolution during subtransus processing. The globularization of lamellar α is analyzed in detail from three aspects, i.e., globularization mechanism, heterogeneity and kinetics. The typical features of flow behaviors and the explanations of significant flow softening are then summarized. The recent advances in modelling of microstructure evolution and flow behaviors in the subtransus processing are also articulated. The current tantalized issues and challenges in understanding of the microstructure evolution and flow behaviors of the titanium alloys with lamellar microstructure are presented and specified in future exploration of them.展开更多
What effect does electric current do on dislocation evolution of metals keeps being a confusing question to be answered and proved. To this end, the dislocation evolution of a superalloy with electric current was dire...What effect does electric current do on dislocation evolution of metals keeps being a confusing question to be answered and proved. To this end, the dislocation evolution of a superalloy with electric current was directly observed by electrical in-situ transmission electron microscopy in this work. Dislocations annihilation at first and then regeneration was found for the first time, which directly proves the existence of electron force during the electrically-assisted manufacturing. Dislocations regeneration would be driven by the electron force and the resistance softening by the local Joule heating effect. Resultantly,a base could be provided for future electrically-assisted research.展开更多
The cast preformed forming process(CPFP) is increasingly considered and applied in the metal forming industries due to its short process, low cost, and environmental friendliness, especially in the aerospace field. Ho...The cast preformed forming process(CPFP) is increasingly considered and applied in the metal forming industries due to its short process, low cost, and environmental friendliness, especially in the aerospace field. However, how to establish a unified model of a non-uniform as-cast billet depicting the flow stress and microstructure evolution behaviors during hot working is the key to microstructure prediction and parameter optimization of the CPFP. In this work, hot compression tests are performed using a non-uniform as-cast 42 CrMo billet at 1123–1423 K and 0.01–1sà1. The effect laws of the non-uniform state of the as-cast billet with different initial grain sizes on the flow stress and microstructure are revealed deeply. Based on experimental results, a unified model of flow stress and grain size evolutions is developed by the internal variable modeling method. Verified results show that the model can well describe the responses of the flow stress and microstructure to deformation conditions and initial grain sizes. To further evaluate its reliability, the unified model is applied to FE simulation of the cast preformed ring rolling process.The predictions of the rolling force and grain size indicate that it could well describe the flow stress and microstructure evolutions during the process.展开更多
Avoiding the folding defect and improving the die filling capability in the transitional region are desired in isothermal local loading forming of a large-scale Ti-alloy rib-web component（LTRC）. To achieve a high-pr...Avoiding the folding defect and improving the die filling capability in the transitional region are desired in isothermal local loading forming of a large-scale Ti-alloy rib-web component（LTRC）. To achieve a high-precision LTRC, the folding evolution and die filling process in the transitional region were investigated by 3 D finite element simulation and experiment using an equal-thickness billet（ETB）. It is found that the initial volume distribution in the second-loading region can greatly affect the amount of material transferred into the first-loading region during the second-loading step, and thus lead to the folding defect. Besides, an improper initial volume distribution results in non-concurrent die filling in the cavities of ribs after the second-loading step, and then causes die underfilling. To this end, an unequal-thickness billet（UTB） was employed with the initial volume distribution optimized by the response surface method（RSM）. For a certain eigenstructure, the critical value of the percentage of transferred material determined by the ETB was taken as a constraint condition for avoiding the folding defect in the UTB optimization process,and the die underfilling rate was considered as the optimization objective. Then, based on the RSM models of the percentage of transferred material and the die underfilling rate, non-folding parameter combinations and optimum die filling were achieved. Lastly, an optimized UTB was obtained and verified by the simulation and experiment.展开更多
How to form high-quality transverse inner ribs through power spinning is a key issue for complicated integrated curved generatrix parts with transverse inner ribs. In this study, the forming characteristics and laws d...How to form high-quality transverse inner ribs through power spinning is a key issue for complicated integrated curved generatrix parts with transverse inner ribs. In this study, the forming characteristics and laws during the power spinning process were investigated using a finite element simulation based on the orthogonal design method. The results show that the transverse inner rib distributes homogeneously along the circumferential direction but inhomogeneously along the generatrix direction. Depressions occur easily in the middle zone of the rib (MZR). The roller nose radius is the most significant parameter of the MZR underfill degree. A larger roller nose radius is helpful to decrease the MZR underfill degree. Furthermore, the preformed billet thickness also plays a vital role in the underfill degree of the front zone of the rib and the back zone of the rib, as well as the depression degree of the outer surface of the rib. By combining the ribfilling characteristics and laws, the optimized forming process window for obtaining high-quality inner ribs was obtained by regression analysis, thus laying a basis for improving the forming quality of curved generatrix parts with transverse inner ribs in power spinning.展开更多
The microstructural evolution of a Ni-based superalloy under interrupted hot compressive deformation with different cooling rates in the inter-pass stage is investigated. It is found that metadynamic recrystallization...The microstructural evolution of a Ni-based superalloy under interrupted hot compressive deformation with different cooling rates in the inter-pass stage is investigated. It is found that metadynamic recrystallization(MDRX) in the inter-pass stage is more sensitive to the accumulated strain than the deformation temperature which is above the recrystallization temperature. The variations of both the grain distribution and the texture intensity caused by MDRX during the interpass stage result in variations of the yield stress(YS) and the work hardening(WH) rate in each stage. Results also show that the MDRX process in the inter-pass stage has a considerable influence on the final microstructure of three-pass compression. The final grain distribution is more uniform,and the compression texture gradually transforms into recrystallization texture with an increasing degree of MDRX. In order to predict the MDRX fraction in the inter-pass cooling stage, a modified kinetic equation is established, which can reasonably predict the MDRX behavior under multi-pass compression with different conditions in the inter-pass stage. Meanwhile, the influence of the interpass cooling stage on the mechanism of dynamic recrystallization(DRX) is studied. It is universally acknowledged that the discontinuous dynamic recrystallization(DDRX) process is the major deformation mechanism for the Ni-based superalloy. However, the continuous dynamic recrystallization(CDRX) process is promoted in the compression stage with a decrease of the cooling rate in each inter-pass stage.展开更多
Revealing the mesoscale deformation mechanisms of titanium alloy with tri-modal microstructure is of great significance to improve its mechanical properties. In this work, the collective behavior and mechanisms of sli...Revealing the mesoscale deformation mechanisms of titanium alloy with tri-modal microstructure is of great significance to improve its mechanical properties. In this work, the collective behavior and mechanisms of slip activities, slip transfer, and grain boundary sliding of tri-modal microstructure were investigated by the combination of quasi-in-situ tensile test, SEM, EBSD and quantitative slip trace analyses. It is found that the slip behavior presents different characteristics in the equiaxed α(α_(p)) and lamellar α(α_(l))grains. Under a low level of deformation, almost all the slip deformation is governed by single basal and prismatic slips for both of α_(p)and α_(l),despite small amount of < a >-pyramidal slip exists in α_(l)grains. As deformation proceeds, < a >-pyramidal and < c + a >-pyramidal slip systems with high Schmid factors were activated in quantities. Specially, certain coarse prismatic slip bands were produced across both of single and colony α_(l)grains whose major axes tilting about 40 °–70 ° from the tensile axis. Slip transfer occurs at the boundaries of α_(p)/α_(p)and α_(l)/β under the condition that there exists perfect alignment between two slip systems and high Schmid factors of outgoing slip system. The slip transfer across α_(l)/β boundary can be divided into two types: straight slip transfer and deflect slip transfer with a deviation angle of 5 °–12 °, depending on the alignment of slip planes of two slip systems. The grain boundary sliding along boundaries of α_(l)/β and α_(p)/β was captured by covering micro-grid on tensile sample. It is found that the crystallographic orientation and the geometrical orientation related to loading axis play great roles in the occurrence of grain boundary sliding.展开更多
A constitutive model that can describe the damage evolution of anisotropic metal sheets during the complex forming processes which experience wide stress triaxiality history is essential to accurately predict the defo...A constitutive model that can describe the damage evolution of anisotropic metal sheets during the complex forming processes which experience wide stress triaxiality history is essential to accurately predict the deformation and rupture behaviors of the processes.In this study,a modified Lemaitre damage criterion which couples with the anisotropic Barlat 89 yield function is established.The effects of stress triaxiality,Lode parameter and shear stress on damage accumulation are considered in the constitutive model.The model is numerically implemented and applied to fracture prediction in tensile tests with different stress triaxialities and a complex deformation process with wide stress triaxiality history.The good consistency of predictions and experiments indicates that the modified Lemaitre damage model has excellent fracture prediction ability.Finally,the accuracy of the model is analyzed and discussed.展开更多
Revealing the development of microstructural inhomogeneity in the multi-pass flow forming of titanium alloy components is of great significance to the microstructure control and property tailoring.To this end,the micr...Revealing the development of microstructural inhomogeneity in the multi-pass flow forming of titanium alloy components is of great significance to the microstructure control and property tailoring.To this end,the microstructural inhomogeneity of TA15 alloy spun cylindrical parts was analyzed based on the deformation history.The results indicate that the material underwent significant compressive strain in the normal direction(ND),tension strain in the rolling and circumferential directions(RD and CD),while tension strain in the CD is slightly small due to the limited material flow in this direction.These strain characteristics make the microstructure,especially the primary a(ap),present different morphologies in the different planes of the part.Meanwhile,the combined effects of inhomogeneous deformation and temperature distribution in the ND also cause the inhomogeneity of microstructure morphology and parameters in this direction.Quantitative analyses show that with the forming pass increasing,the aspect ratio of apincreases most in the normal-rolling plane,then in the normal-circumferential plane and least in the circumferential-rolling plane,whereas apcontent decreases in an opposite trend.Along the ND,the aspect ratio and content of apis relatively high in the outer and inner surface areas but lowest in the central area,and these inhomogeneous characteristics can be gradually diminished with the forming pass increasing.Furthermore,the variation of hardness inhomogeneity factor indicates that a four-pass forming with the total reduction ratio of 63%could obtain a homogenous microstructure along the ND of the TA15 alloy spun cylindrical part.展开更多
Nowadays, more and more attentions are paid to electromagnetic incremental forming（EMIF）, especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a pa...Nowadays, more and more attentions are paid to electromagnetic incremental forming（EMIF）, especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X＂ discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z＂ discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.展开更多
Anisotropy of mechanical property is an important feature influencing the service performance of titanium(Ti)alloy tube component.In this work,it is found that the hot flow formed Ti alloy tube exhibits higher yield s...Anisotropy of mechanical property is an important feature influencing the service performance of titanium(Ti)alloy tube component.In this work,it is found that the hot flow formed Ti alloy tube exhibits higher yield strength along circumferential direction(CD),and larger elongation along rolling direction(RD),presenting significant anisotropy.Subsequently,the quantitative characteristics and underlying mechanism of the property anisotropy were revealed by analyzing the slip,damage and fracture behavior under the combined effects of the spun{0002}basal texture and fibrous microstructure for different loading directions.The results showed that the prismatic slip in primaryαgrain is the dominant deformation mechanism for both loading directions at the yielding stage.The prismatic slip is harder under CD loading,which makes CD loading present higher yield strength than RD loading.Additionally,the yield anisotropy can be quantified through the inverse ratio of the averaged Schmid Factor of the activated prismatic slip under different loading directions.As for the plasticity anisotropy,the harder and slower slip development under CD loading causes that the CD loading presents larger external force and normal stress on slip plane,thus leading to more significant cleavage fracture than RD loading.Moreover,the micro-crack path under RD loading is more tortuous than CD loading because the fibrous microstructure is elongated along RD,which may suppress the macro fracture under RD loading.These results suggest that weakening the texture and fibrous morphology of microstructure is critical to reduce the differences in slip,damage and fracture behavior along different directions,alleviate the property anisotropy and optimize the service performance of Ti alloy tube formed by hot flow forming.展开更多
The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state.In this study,their dependences on processing parameters were...The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state.In this study,their dependences on processing parameters were investigated by an integrated FE model considering microstructure and damage evolution,and revealing the effects of microstructure and stress states on damage evolution.The results show that the inner surface of workpiece with the largest voids volume fraction is the place with the greatest potential of fracture.This is mainly attributed to the superposition effects of positive stress triaxiality and the smallest dynamic recrystallization(DRX)fraction andβphase fraction at the inner surface.The damage degree is decreased gradually with the increase of initial spinning temperature and roller fillet radius.Meanwhile,it is first decreased and then increased with the increases of spinning pass and roller feed rate,which can be explained based on the variations ofβphase fraction,DRX fraction,stress state and tensile plastic strain with processing parameters.In addition,the dominant influencing mechanisms were identified and discussed.Finally,the thickness reduction without defect in the hot spinning of TA15 alloy tube is greatly increased by proposing an optimal processing scheme.展开更多
Billet optimization can greatly improve the forming quality of the transitional region in the isothermal local loading forming （ILLF） of large-scale Ti-alloy ribweb components. However, the final quality of the tran...Billet optimization can greatly improve the forming quality of the transitional region in the isothermal local loading forming （ILLF） of large-scale Ti-alloy ribweb components. However, the final quality of the transitional region may be deteriorated by uncontrollable factors, such as the manufacturing tolerance of the preforming billet, fluctuation of the stroke length, and friction factor. Thus, a dual-response surface method （RSM）-based robust optimization of the billet was proposed to address the uncontrollable factors in transi- tional region of the ILLF. Given that the die underfilling and folding defect are two key factors that influence the forming quality of the transitional region, minimizing the mean and standard deviation of the die underfilling rate and avoiding folding defect were defined as the objective function and constraint condition in robust optimization. Then, the cross array design was constructed, a dual-RSM model was established for the mean and standard deviation of the die underfilling rate by considering the size parameters of the billet and uncontrollable factors. Subsequently, an optimum solution was derived to achieve the robust optimization of the billet. A case study on robust optimization was conducted. Good results were attained for improving the die filling and avoiding folding defect, suggesting that the robust optimization of the billet in the transitional region of the ILLF was efficient and reliable.展开更多
In the present work, the coupled effects of initial structure and processing parameters on microstructure of a two-phase titanium alloy were investigated to predict the microstructural evolution in multiple hot workin...In the present work, the coupled effects of initial structure and processing parameters on microstructure of a two-phase titanium alloy were investigated to predict the microstructural evolution in multiple hot working. It is found that microstructure with different constituent phases can be obtained by regulating the initial structure and hot working conditions. The variation of deformation degree and cooling rate can change the morphology of the con- stituent phases, but do not alter the phase fraction. The phase transformation during heating and holding determi- nes the phase fraction for a certain initial structure. ^--at-~3 transformation occurs during heating and holding. [3 to ct transformation leads to a significant increase in content and size of lamellar ~. The ct to [3 transformation occurs simultaneously in equiaxed at and lamellar ct. The thickness of lamellar ~t increases with temperature, which is caused by the vanishing of fine a lamellae due to phase transformation and coarsening by termination migration. By assuming a quasi-equilibrium phase transformation in heating and holding, a modeling approach is proposed for predicting microstructural evolution. The three stages of phase transformation are modeled separately and combined to predict the variation of phase fraction with temperature. Model predictions agree well with the experimental results.展开更多
Nano-sized quantum dots（QDs） exhibit uniquely optical properties that are tunable with different sizes and shapes.QDs can emit narrow symmetric bands under a wide excitation range,possess antiphotobleaching stabilit...Nano-sized quantum dots（QDs） exhibit uniquely optical properties that are tunable with different sizes and shapes.QDs can emit narrow symmetric bands under a wide excitation range,possess antiphotobleaching stability,and be bio-functionalized on the large surface area.Therefore,QDs are attractive vectors for imaging-guided therapy.Small-interfering RNA（siRNAs）-based therapeutics hold great potential to target a large part of the currently undruggable genes,but overcoming the lipid bilayer to deliver siRNA into cells has remained a major challenge to solve for widespread development of siRNA therapeutics.In this mini-review,we focus on theranostic QD/siRNA assembles for enhancing delivery of siRNA and facilitating evaluation of therapeutic efficacy via imaging of QDs,with special attention to carbonaceous QDs for delivery of siRNA.展开更多
基金supported by the National Natural Science Foundation of China(grant no.52192603,52275308).
文摘A novel lightweight,radiation-shielding Mg-Ta-Al layered metal-matrix composite(LMC)was successful designed by doping the extremely refractory metal(Ta)into Mg sheets.These Mg-based LMCs sheets shows excellent radiation-dose shield effect,about 145 krad·a^(−1),which is about 17 times of traditional Mg alloy,while its surface density is only about 0.9 g·cm^(−2),reducing by 60%than that of pure Ta.The quantitate relationship between radiation-dose and the materials’thickness was also confirmed to the logistic function when the surface density is in the range of 0.6-1.5 g·cm^(−2).Meantime,the rolling parameters,interface microstructure and mechanical properties in both as-rolled and annealing treated samples were evaluated.The sheets possess a special dissimilar atoms diffusion transitional zone containing an obvious inter-diffusion Mg-Al interface and the unique micro-corrugated Ta-Al interface,as well as a thin Al film with a thickness of about 10μm.The special zone could reduce the stress concentration and enhance the strength of Mg-Ta-Al LMCs.The interface bonding strength reaches up to 54-76 MPa.The ultimate tensile strength(UTS)and yield strength(TYS)of the Mg-Ta-Al sheet were high to 413 MPa and 263 MPa,respectively,along with an elongation of 5.8%.The molecular dynamics(MD)analysis results show that the two interfaces exhibit different formation mechanism,the Mg-Al interface primarily depended on Mg/Al atoms diffusion basing point defects movement,while the Ta-Al interface with a micro-interlock pining shape formed by close-packed planes slipping during high temperature strain-induced deformation process.
基金Project(SKLSP201853) supported by the Fund of the State Key Laboratory of Solidification Processing in NWPU,ChinaProject(51625505) supported by the National Science Fund for Distinguished Young Scholars of China+1 种基金Project(U1537203) supported by the Key Program Project of the Joint Fund of Astronomy and National Natural Science Foundation of ChinaProject(KYQD1801) supported by the Scientific Research Foundation of Tianjin University of Technology and Education,China
文摘The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.
基金Supported by National Natural Science Foundation of China(Grant No.U1737212)National Science and Technology Major Project of China(Grant No.J2019-VII-0014-0154)Shaanxi Provincial Natural Science Foundation for Distinguished Young Scholars of China(Grant No.2019JC-09).
文摘Compared with conventional forming processes,ultrasonic-assisted forming technology with a high frequency and small amplitude can significantly improve the forming quality of materials.Owing to the advantages of reduced forming force,improved surface quality,avoidance of forming defects,and strengthened surface structure,ultrasonic-assisted forming technology has been applied to increasingly advanced forming processes,such as incremental forming,spinning,and micro-forming.However,in the ultrasonic-assisted forming process,there are multiple ultrasonic mechanisms,such as the volume effect and surface effect.The explanation of the effect of ultrasonic vibration(UV)on plastic deformation remains controversial,hindering the development of related technologies.Recently,many researchers have proposed many new theories and technologies for ultrasonic-assisted forming.To summarize these developments,systematic discussions on mechanisms,theoretical models,and forming performances are provided in this review.On this basis,the limitations of the current study are discussed.In addition,an outlook for ultrasonic-assisted forming is proposed:efficient and stable UV systems,difficulty forming components with complex geometry,explanation of the in-depth mechanism,a systematic theoretical prediction model,and multi-field-coupling energy-assisted forming are considered to be hot spots in future studies.The present review enhances existing knowledge of ultrasonic-assisted forming,and facilitates a fast reference for related researchers.
基金financial supports from the National Natural Science Foundation of China(No.51675433)the Natural Science Foundation for Distinguished Young Scholars of Shaanxi Province,China(No.2019JC-09)。
文摘To reveal the affecting mechanism of cooling rate on lamellarαprecipitation,the precipitation behaviors of lamellarαphase in IMI834 titanium alloy during isothermal and non-isothermal heat treatments were quantitatively characterized using experimental analysis.Critical precipitation temperatures at various cooling rates were obtained using thermal dilatation testing.Using metallographic microscopy,electron microprobe analysis,and data fitting methods,the quantitative evolution models of average width,volume fraction,and solute concentration in theαandβphases were built for different temperatures or cooling rates.A comparison between the two precipitation behaviors showed that the average width and volume fraction of lamellarαphase under non-isothermal conditions were smaller than those under isothermal conditions.With increasing cooling rate,the average width and volume fraction were decreased significantly,and the critical precipitation temperatures were reduced.This phenomenon is mainly attributed to the decreased diffusion velocity of solutes Al,Mo,and Nb with increasing cooling rate.
基金co-supported by the Young Scientists Fund of the National Natural Science Foundation of China(No.52105417)the Foundation of Civil Aviation Flight University of China(Nos.J2022-067,ZJ2022-003 and JG2022-27)the National Science Fund for Excellent Young Scholars of China(No.52122509).
文摘The quenching-spinning(Q-S)process,i.e.,shear spinning after blank quenching,has been increasingly utilized to form 2219 aluminum alloy complex thin-walled components.However,the changes in material property,shape and stress of the blanks after quenching will affect the spin-ning forming precision.In this study,the rules and mechanisms of these effects are investigated based on a combined finite element(FE)model including blank quenching and component spinning process.The results indicate that the increase of material strength and the existence of distortion of the quenched blank lead to a notable increase in the non-uniformity of the circumferential compres-sive stress in the spinning area and the increase of the flange swing height during spinning.These changes result in an increase in the wall thickness and component-mandrel gap of the components.The quenching residual stress has little effect on wall thickness and roundness but can noticeably reduce the component-mandrel gap.This is because that the existence of quenching residual stress of the blank can lead to the decrease of the maximum circumferential compressive stress of the workpiece in spinning and an obvious drop in the maximum compressive stress after reaching the stress peak.Quenching distortion is the main factor affecting the roundness.Moreover,the opti-mized installation way of the blank for spinning is obtained.
基金the support of National Natural Science Foundation of China(Nos.51605388,51875467)the Hong Kong Scholar Program(No.XJ2018010)the Young Elite Scientists Sponsorship Program by CAST(No.2018QNRC001).
文摘Titanium alloys have been widely used in many industrial clusters such as automotive, aerospace and biomedical industries due to their excellent comprehensive properties. In order to obtain fine microstructures and favorable properties, a well-designed multi-step thermomechanical processing(TMP) is critically needed in manufacturing of titanium components. In making of titanium components,subtransus processing is a critical step to breakdown lamellar microstructure to fine-structure in hot working process and thus plays a key role in tailoring the final microstructure and properties. To realize this goal, huge efforts have been made to investigate the mechanisms of microstructure evolution and flow behavior during the subtransus processing. This paper reviews the recent experimental and modelling progresses, which aim to provide some guidelines for the process design and microstructure tailoring for titanium alloy research community. The characteristics of the initial lamellar microstructure are presented, followed by the discussion on microstructure evolution during subtransus processing. The globularization of lamellar α is analyzed in detail from three aspects, i.e., globularization mechanism, heterogeneity and kinetics. The typical features of flow behaviors and the explanations of significant flow softening are then summarized. The recent advances in modelling of microstructure evolution and flow behaviors in the subtransus processing are also articulated. The current tantalized issues and challenges in understanding of the microstructure evolution and flow behaviors of the titanium alloys with lamellar microstructure are presented and specified in future exploration of them.
基金financially supported by the National Natural Science Foundation of China(Nos.U1737212 and U1637102)the Natural Science Foundation for Distinguished Young Scholars of Shaanxi Province(No.2019JC-09)。
文摘What effect does electric current do on dislocation evolution of metals keeps being a confusing question to be answered and proved. To this end, the dislocation evolution of a superalloy with electric current was directly observed by electrical in-situ transmission electron microscopy in this work. Dislocations annihilation at first and then regeneration was found for the first time, which directly proves the existence of electron force during the electrically-assisted manufacturing. Dislocations regeneration would be driven by the electron force and the resistance softening by the local Joule heating effect. Resultantly,a base could be provided for future electrically-assisted research.
基金supported by the National Natural Science Foundation of China (No’s. 51575448 and 51135007)
文摘The cast preformed forming process(CPFP) is increasingly considered and applied in the metal forming industries due to its short process, low cost, and environmental friendliness, especially in the aerospace field. However, how to establish a unified model of a non-uniform as-cast billet depicting the flow stress and microstructure evolution behaviors during hot working is the key to microstructure prediction and parameter optimization of the CPFP. In this work, hot compression tests are performed using a non-uniform as-cast 42 CrMo billet at 1123–1423 K and 0.01–1sà1. The effect laws of the non-uniform state of the as-cast billet with different initial grain sizes on the flow stress and microstructure are revealed deeply. Based on experimental results, a unified model of flow stress and grain size evolutions is developed by the internal variable modeling method. Verified results show that the model can well describe the responses of the flow stress and microstructure to deformation conditions and initial grain sizes. To further evaluate its reliability, the unified model is applied to FE simulation of the cast preformed ring rolling process.The predictions of the rolling force and grain size indicate that it could well describe the flow stress and microstructure evolutions during the process.
基金supports of the National Natural Science Foundation of China (No. 51575449)Research Fund of the State Key Laboratory of Solidification Processing (NWPU) of China (No. 104-QP2014)+1 种基金the 111 Project (No. B08040)the Fundamental Research Funds for the Central Universities (3102015AX004)
文摘Avoiding the folding defect and improving the die filling capability in the transitional region are desired in isothermal local loading forming of a large-scale Ti-alloy rib-web component（LTRC）. To achieve a high-precision LTRC, the folding evolution and die filling process in the transitional region were investigated by 3 D finite element simulation and experiment using an equal-thickness billet（ETB）. It is found that the initial volume distribution in the second-loading region can greatly affect the amount of material transferred into the first-loading region during the second-loading step, and thus lead to the folding defect. Besides, an improper initial volume distribution results in non-concurrent die filling in the cavities of ribs after the second-loading step, and then causes die underfilling. To this end, an unequal-thickness billet（UTB） was employed with the initial volume distribution optimized by the response surface method（RSM）. For a certain eigenstructure, the critical value of the percentage of transferred material determined by the ETB was taken as a constraint condition for avoiding the folding defect in the UTB optimization process,and the die underfilling rate was considered as the optimization objective. Then, based on the RSM models of the percentage of transferred material and the die underfilling rate, non-folding parameter combinations and optimum die filling were achieved. Lastly, an optimized UTB was obtained and verified by the simulation and experiment.
基金the National Science Fund for Distinguished Young Scholars of China (Grant No. 51625505)the Key Program Project of the Joint Fund of Astronomy and the National Natural Science Foundation of China (Grant No. U1537203)the Open Research Fund of State Key Laboratory of High Performance Complex Manufacturing, Central South University.
文摘How to form high-quality transverse inner ribs through power spinning is a key issue for complicated integrated curved generatrix parts with transverse inner ribs. In this study, the forming characteristics and laws during the power spinning process were investigated using a finite element simulation based on the orthogonal design method. The results show that the transverse inner rib distributes homogeneously along the circumferential direction but inhomogeneously along the generatrix direction. Depressions occur easily in the middle zone of the rib (MZR). The roller nose radius is the most significant parameter of the MZR underfill degree. A larger roller nose radius is helpful to decrease the MZR underfill degree. Furthermore, the preformed billet thickness also plays a vital role in the underfill degree of the front zone of the rib and the back zone of the rib, as well as the depression degree of the outer surface of the rib. By combining the ribfilling characteristics and laws, the optimized forming process window for obtaining high-quality inner ribs was obtained by regression analysis, thus laying a basis for improving the forming quality of curved generatrix parts with transverse inner ribs in power spinning.
基金supports from the National Natural Science Foundation of China(U1737212and U1637102)the Research Fund of the State Key Laboratory of Solidification Processing(NWPU,China)(Grant No.149-QZ-2016)+1 种基金the Fundamental Research Funds for the Central Universities(3102017jc03009)The Analytical&Testing Center at Northwestern Polytechnical University is also acknowledged for the experimental support on this work
文摘The microstructural evolution of a Ni-based superalloy under interrupted hot compressive deformation with different cooling rates in the inter-pass stage is investigated. It is found that metadynamic recrystallization(MDRX) in the inter-pass stage is more sensitive to the accumulated strain than the deformation temperature which is above the recrystallization temperature. The variations of both the grain distribution and the texture intensity caused by MDRX during the interpass stage result in variations of the yield stress(YS) and the work hardening(WH) rate in each stage. Results also show that the MDRX process in the inter-pass stage has a considerable influence on the final microstructure of three-pass compression. The final grain distribution is more uniform,and the compression texture gradually transforms into recrystallization texture with an increasing degree of MDRX. In order to predict the MDRX fraction in the inter-pass cooling stage, a modified kinetic equation is established, which can reasonably predict the MDRX behavior under multi-pass compression with different conditions in the inter-pass stage. Meanwhile, the influence of the interpass cooling stage on the mechanism of dynamic recrystallization(DRX) is studied. It is universally acknowledged that the discontinuous dynamic recrystallization(DDRX) process is the major deformation mechanism for the Ni-based superalloy. However, the continuous dynamic recrystallization(CDRX) process is promoted in the compression stage with a decrease of the cooling rate in each inter-pass stage.
基金the support of the National Natural Science Foundation of China(No.51875467,92060107)the National Science Fund for Distinguished Young Scholars of China(No.51625505)+2 种基金the National Key R&D Program of China(No.2020YFA0711100)Young Elite Scientists Sponsorship Program and the General Program of ScienceTechnology Development Project of Beijing Municipal Education Commission(No.KM202010005008)
文摘Revealing the mesoscale deformation mechanisms of titanium alloy with tri-modal microstructure is of great significance to improve its mechanical properties. In this work, the collective behavior and mechanisms of slip activities, slip transfer, and grain boundary sliding of tri-modal microstructure were investigated by the combination of quasi-in-situ tensile test, SEM, EBSD and quantitative slip trace analyses. It is found that the slip behavior presents different characteristics in the equiaxed α(α_(p)) and lamellar α(α_(l))grains. Under a low level of deformation, almost all the slip deformation is governed by single basal and prismatic slips for both of α_(p)and α_(l),despite small amount of < a >-pyramidal slip exists in α_(l)grains. As deformation proceeds, < a >-pyramidal and < c + a >-pyramidal slip systems with high Schmid factors were activated in quantities. Specially, certain coarse prismatic slip bands were produced across both of single and colony α_(l)grains whose major axes tilting about 40 °–70 ° from the tensile axis. Slip transfer occurs at the boundaries of α_(p)/α_(p)and α_(l)/β under the condition that there exists perfect alignment between two slip systems and high Schmid factors of outgoing slip system. The slip transfer across α_(l)/β boundary can be divided into two types: straight slip transfer and deflect slip transfer with a deviation angle of 5 °–12 °, depending on the alignment of slip planes of two slip systems. The grain boundary sliding along boundaries of α_(l)/β and α_(p)/β was captured by covering micro-grid on tensile sample. It is found that the crystallographic orientation and the geometrical orientation related to loading axis play great roles in the occurrence of grain boundary sliding.
基金co-supported by the National Science Fund for Distinguished Young Scholars of China(No.51625505)the National Natural Science Foundation of China(Nos.U1910213 and U1937203)the Independent Research Project of State Key Laboratory of Solidification Processing of Northwestern Polytechnical University(No.2019-TZ-02)。
文摘A constitutive model that can describe the damage evolution of anisotropic metal sheets during the complex forming processes which experience wide stress triaxiality history is essential to accurately predict the deformation and rupture behaviors of the processes.In this study,a modified Lemaitre damage criterion which couples with the anisotropic Barlat 89 yield function is established.The effects of stress triaxiality,Lode parameter and shear stress on damage accumulation are considered in the constitutive model.The model is numerically implemented and applied to fracture prediction in tensile tests with different stress triaxialities and a complex deformation process with wide stress triaxiality history.The good consistency of predictions and experiments indicates that the modified Lemaitre damage model has excellent fracture prediction ability.Finally,the accuracy of the model is analyzed and discussed.
基金the financial support from the National Science Fund for Distinguished Young Scholars of China(No.51625505)the Key Program Project of the Joint Fund of Astronomy and National Natural Science Foundation of China(No.U1537203)+1 种基金National Natural Science Foundation of China(No.51875467)the support of Young Elite Scientists Sponsorship Program by CAST of China(No.2018QNRC001)。
文摘Revealing the development of microstructural inhomogeneity in the multi-pass flow forming of titanium alloy components is of great significance to the microstructure control and property tailoring.To this end,the microstructural inhomogeneity of TA15 alloy spun cylindrical parts was analyzed based on the deformation history.The results indicate that the material underwent significant compressive strain in the normal direction(ND),tension strain in the rolling and circumferential directions(RD and CD),while tension strain in the CD is slightly small due to the limited material flow in this direction.These strain characteristics make the microstructure,especially the primary a(ap),present different morphologies in the different planes of the part.Meanwhile,the combined effects of inhomogeneous deformation and temperature distribution in the ND also cause the inhomogeneity of microstructure morphology and parameters in this direction.Quantitative analyses show that with the forming pass increasing,the aspect ratio of apincreases most in the normal-rolling plane,then in the normal-circumferential plane and least in the circumferential-rolling plane,whereas apcontent decreases in an opposite trend.Along the ND,the aspect ratio and content of apis relatively high in the outer and inner surface areas but lowest in the central area,and these inhomogeneous characteristics can be gradually diminished with the forming pass increasing.Furthermore,the variation of hardness inhomogeneity factor indicates that a four-pass forming with the total reduction ratio of 63%could obtain a homogenous microstructure along the ND of the TA15 alloy spun cylindrical part.
基金supported by the National Science Fund for Distinguished Young Scholars of China (No.51625505)the Key Program Project of the Joint Fund of Astronomy and National Natural Science Foundation of China (No.U1537203)the National Key Basic Research Program of China (No.2011CB012804)
文摘Nowadays, more and more attentions are paid to electromagnetic incremental forming（EMIF）, especially for a part with a large-scale size, e.g., an integral panel with stiffened ribs. In this work, the bending of a panel into a double-curvature profile via EMIF is carried out experimentally and evaluated by comparing the formed profile with the desired profile. During the process,discharges at four positions along different discharge paths are designed. The effects of forming parameters on the die-fittingness of the workpiece are discussed, for which two evaluation indices are used to judge forming results. The results show that a discharge voltage in an incremental mode is helpful to improve the fittingness and avoid the collision rebound against the die at the same time.Discharging at the diagonal positions with the ‘‘X＂ discharge path exhibits the minimal shape deviation and the best forming uniformity. On the contrary, discharging at the parallel positions with the ‘‘Z＂ discharge path obtains the worst forming quality. Overlap of the coil at different positions should be given during EMIF; however, a lower overlap rate of the coil helps improve the forming quality. The results obtained in this work are useful for forming integral panels with stiffened ribs via the EMIF process.
基金financially supported by the National Natural Science Foundation of China(No.51875467,52005313)the National Science Fund for Distinguished Young Scholars of China(No.51625505)+1 种基金the Young Elite Scientists Sponsorship Program by CAST(No.2018QNRC001)the Research Fund of the State Key Laboratory of Solidification Processing(NPU)of China(No.2019TS-10)。
文摘Anisotropy of mechanical property is an important feature influencing the service performance of titanium(Ti)alloy tube component.In this work,it is found that the hot flow formed Ti alloy tube exhibits higher yield strength along circumferential direction(CD),and larger elongation along rolling direction(RD),presenting significant anisotropy.Subsequently,the quantitative characteristics and underlying mechanism of the property anisotropy were revealed by analyzing the slip,damage and fracture behavior under the combined effects of the spun{0002}basal texture and fibrous microstructure for different loading directions.The results showed that the prismatic slip in primaryαgrain is the dominant deformation mechanism for both loading directions at the yielding stage.The prismatic slip is harder under CD loading,which makes CD loading present higher yield strength than RD loading.Additionally,the yield anisotropy can be quantified through the inverse ratio of the averaged Schmid Factor of the activated prismatic slip under different loading directions.As for the plasticity anisotropy,the harder and slower slip development under CD loading causes that the CD loading presents larger external force and normal stress on slip plane,thus leading to more significant cleavage fracture than RD loading.Moreover,the micro-crack path under RD loading is more tortuous than CD loading because the fibrous microstructure is elongated along RD,which may suppress the macro fracture under RD loading.These results suggest that weakening the texture and fibrous morphology of microstructure is critical to reduce the differences in slip,damage and fracture behavior along different directions,alleviate the property anisotropy and optimize the service performance of Ti alloy tube formed by hot flow forming.
基金the funding support from the National Natural Science Foundation of China(No.51875467,92060107)National Science Fund for Distinguished Young Scholars of China(No.51625505)+2 种基金the Hong Kong Scholar Program(No.XJ2018010)the Young Elite Scientists Sponsorship Program by CAST(No.2018QNRC001)the Research Fund of the State Key Laboratory of Solidification Processing(NPU),China(Grant No.2019-TS-10)。
文摘The damage and fracture in hot spinning of titanium alloy is a very complex process under the combined effects of microstructure evolution and stress state.In this study,their dependences on processing parameters were investigated by an integrated FE model considering microstructure and damage evolution,and revealing the effects of microstructure and stress states on damage evolution.The results show that the inner surface of workpiece with the largest voids volume fraction is the place with the greatest potential of fracture.This is mainly attributed to the superposition effects of positive stress triaxiality and the smallest dynamic recrystallization(DRX)fraction andβphase fraction at the inner surface.The damage degree is decreased gradually with the increase of initial spinning temperature and roller fillet radius.Meanwhile,it is first decreased and then increased with the increases of spinning pass and roller feed rate,which can be explained based on the variations ofβphase fraction,DRX fraction,stress state and tensile plastic strain with processing parameters.In addition,the dominant influencing mechanisms were identified and discussed.Finally,the thickness reduction without defect in the hot spinning of TA15 alloy tube is greatly increased by proposing an optimal processing scheme.
基金Acknowledgements The authors would like to gratefully acknowledge the support given by the National Natural Science Foundation of China （Grant No. 51575449）, Research Fund of the State Key Laboratory of Solidification Processing （NWPU）, China （Grant No. 104-QP-2014）, 111 Project （Grant No. B08040）, and Fundamental Research Funds for the Central Universities （Grant No. 3102015AX004）.
文摘Billet optimization can greatly improve the forming quality of the transitional region in the isothermal local loading forming （ILLF） of large-scale Ti-alloy ribweb components. However, the final quality of the transitional region may be deteriorated by uncontrollable factors, such as the manufacturing tolerance of the preforming billet, fluctuation of the stroke length, and friction factor. Thus, a dual-response surface method （RSM）-based robust optimization of the billet was proposed to address the uncontrollable factors in transi- tional region of the ILLF. Given that the die underfilling and folding defect are two key factors that influence the forming quality of the transitional region, minimizing the mean and standard deviation of the die underfilling rate and avoiding folding defect were defined as the objective function and constraint condition in robust optimization. Then, the cross array design was constructed, a dual-RSM model was established for the mean and standard deviation of the die underfilling rate by considering the size parameters of the billet and uncontrollable factors. Subsequently, an optimum solution was derived to achieve the robust optimization of the billet. A case study on robust optimization was conducted. Good results were attained for improving the die filling and avoiding folding defect, suggesting that the robust optimization of the billet in the transitional region of the ILLF was efficient and reliable.
基金financially supported by the National Natural Science Foundation of China (No. 51575449)the 111 Project (B08040)the Research Fund of the State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, China (No. 104-QP-2014)
文摘In the present work, the coupled effects of initial structure and processing parameters on microstructure of a two-phase titanium alloy were investigated to predict the microstructural evolution in multiple hot working. It is found that microstructure with different constituent phases can be obtained by regulating the initial structure and hot working conditions. The variation of deformation degree and cooling rate can change the morphology of the con- stituent phases, but do not alter the phase fraction. The phase transformation during heating and holding determi- nes the phase fraction for a certain initial structure. ^--at-~3 transformation occurs during heating and holding. [3 to ct transformation leads to a significant increase in content and size of lamellar ~. The ct to [3 transformation occurs simultaneously in equiaxed at and lamellar ct. The thickness of lamellar ~t increases with temperature, which is caused by the vanishing of fine a lamellae due to phase transformation and coarsening by termination migration. By assuming a quasi-equilibrium phase transformation in heating and holding, a modeling approach is proposed for predicting microstructural evolution. The three stages of phase transformation are modeled separately and combined to predict the variation of phase fraction with temperature. Model predictions agree well with the experimental results.
基金supported by the National Natural Science Foundation of China(No.81602699)the National High Technology Research and Development Program of China(No.2015AA020309)the China Postdoctoral Science Foundation funded project(No.2015M570791)
文摘Nano-sized quantum dots（QDs） exhibit uniquely optical properties that are tunable with different sizes and shapes.QDs can emit narrow symmetric bands under a wide excitation range,possess antiphotobleaching stability,and be bio-functionalized on the large surface area.Therefore,QDs are attractive vectors for imaging-guided therapy.Small-interfering RNA（siRNAs）-based therapeutics hold great potential to target a large part of the currently undruggable genes,but overcoming the lipid bilayer to deliver siRNA into cells has remained a major challenge to solve for widespread development of siRNA therapeutics.In this mini-review,we focus on theranostic QD/siRNA assembles for enhancing delivery of siRNA and facilitating evaluation of therapeutic efficacy via imaging of QDs,with special attention to carbonaceous QDs for delivery of siRNA.
